i3 i3TOUCH V-Sense V7004 T10 User manual

i3TOUCH
OPERATIONS MANUAL

Contents
Safety precautions...................................................................................................................................................................... 2-4
Basic operation................................................................................................................................................................................ 5
Accessories....................................................................................................................................................................................... 5
•Installation....................................................................................................................................................................................... 6
- Connect monitor......................................................................................................................................................................... 6
- Connect satellite receiver or decoder.................................................................................................................................... 6
• Description for the keys on the front panel.......................................................................................................................... 7
• Rear panel interface................................................................................................................................................................. 8-9
• Remote control description.................................................................................................................................................... 10
• Source list.................................................................................................................................................................................... 11
Screen Menu.................................................................................................................................................................................. 12
- Picture.......................................................................................................................................................................................... 13
- Sound............................................................................................................................................................................................14
- Time.............................................................................................................................................................................................. 15
- Lock.............................................................................................................................................................................................. 16
- Setup............................................................................................................................................................................................ 17
- USB Mode................................................................................................................................................................................... 18
- Film Play....................................................................................................................................................................................... 19
• PC Mode (VGA input) specification........................................................................................................................................ 20
• Trouble shooting........................................................................................................................................................................ 21
• Safety precautions..................................................................................................................................................................... 22
Contents

2
www.i3-learning.com
Note: Please read this instruction manual carefully and place it at a place that is easily avaible. Please obey
below installation and operation instructions.
1. Please read the safety precautions and operating instructions carefully before using the product. Please also
keep this instruction manual for further use.
2. Please follow all the warning signs on both products and instruction manual.
< > key on the front panel and remote control is unipolar switch, press this key to switch between on and
standby mode when it is powered on: < > key on the rear panel of the monitor is all-pole switch, press
< > to power off, and press < > to power on. Al-pole power switch: it can disconnect all the manual
mechanical switches of network source at all levels except the one that protects grounding conductor. The
contact seperation of each pole of the all-pole power switch. (Note: If there is no all-pole power switch with
the monitor, then the power plug that connects with the monitor shall be used as the device for power off, the
power plug schould be easy to be plugged.)
4. Please power off and unplug immediately when there is abnormal noise or smell inside the product, don’t
uvse if it is coonfirmed to be abnormal and request professionals for maintenance.
5. Turn off the monitor and unplug the power cord when it is left unused for a long period, and disconnect the
antenna in thunderstorm season.
6. Don’t watch monitor during a lightning storm, unplug the plug and antenna before thunderstorm so as to
avoid a lightning strike.
7. Don’t place any flammable and explosive materials on the monitor set, cradles, electric stove, light bulbs, etc.
can not be placed near the monitor set so as to avoid accidents.
8. Don’t let liquid or metal go into the monitor. If liquid or metal fall into the monitor, don’t turn on or use the
monitor, request a professional service person to deal with it.
9. Don’t clean the product with chemical agent as the dissolvant may cause deterioration to the shell and dam-
age the painted surface. If there is any dust or dirt, use a damp cloth to clean after turning off the monitor for
ten minutes. Clean the screen with clean and soft cloth. Unplug the monitor power cord from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol cleaners.
10. Pay attention to water and moisture. Do not use the product near water, such as bathtub, washbasin,
kitchen sink, laundry tub, swimming pool or in a wet basement.
11. Do not expose this product to dripping or splashing. No objects filled with liquids, such as vases, should be
place on the product.
12. The power plug should be easy to be plugged.
This product may be equipped with a polarized
alternating current tine plug (a plug having one
blade wider than the other). This plug will fit into
the power outlet only in one way. This is a safety
feature. If you are unable to inssert the plug fuly
into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to
Safety precautions

3
i3TOUCH OPTICAL SENSE - operations manual
replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. Additional
warning: this product is equipped with a threewire grounding type plug which has grounding pins. This plug
only fits into the grounding type outlet. This is a safety feature. If you are unableto insert the plug into the out-
let, please contact your electrician to replace your obsolete outlet. Do not defeat the safety purpse of the plug.
14. The slots and openings in the cabinet are designed for ventilation so as to ensure reliable operation and
protect it from overheating. These slots and openings must not be covered or blocked with newspaper, table-
cloth or curtain, etc. Make sure there is some space around the product for sufficient ventilation.
15. This monitor can only be supplied by the power source and power voltage indicated on the marking label.
If you are not sure about the type of power suppy and voltage to your house, please consult the dealer or the
local power supply company.
16. The power,cable of this product in the accessory box is three point plug power cord (with ground protec-
tion), please check whether the ground terminal of the wall outlet is grounded before installing. The power
cords should be routed properly to prevent people from stepping on them or objects from resting on them.
17. It is not allowed to put any sundries into the product through any openings, or maybe they will touch any
dangerous voltage points or projecting parts and cause fire or electric shock.
18. Screen uneven aging, because of the physical characteristics of the plasma screen, it is not allowed to play
static images r texts (such as CD-ROM games and connection with PC for a long time or watch monitor in 4:3
mode, or it may cause screen uneven aging, screen burn, remnant shade and even permanent damage to the
display screen. To avoid screen uneven againning, please reduce the brightness and contrast when the moni-
tor displays static images; If above cases appear, your display screen will not bear the guarranty (Pay attention
to this problem for plasma monitor).
19. When the monitor stays at the static images for over 30 seconds and leaves a remnant shade, which is
caused by the physical characteristics of the plasma, let the monitor play dymic pictures for two minutes, and it
is normal if the remnant shade diappears, hereby declared (Play attention to this problem for plasma monitor)!
20. Don’t service the product by yourself. Removing covers can expose you to high voltage and other dangers.
Contact the serviceman specified by the manufacturer if there is any repairs or maintenance.
21. Follow the operating instructions of the manufacturer when installing the product, only the accessories
recommended by the manufacturer can be used.
22. The wall-mounted (if any) installation of this product is only applicable to the normal cement wall, solid wall
or board wall which can bear the weight more than three times as the product, as for hanging and hoisting in-
stallation to the special wall (such as steel structure wall, hollow structure wall, glass wall and marble wall, etc.),
the manufacturer recommends you to consider the safety before operating. The installation of thes special
materials must be carried out by professionals, the manufacturer does not undertake these installations.
23. The important part with exclamatory mark on the rating label indicates that only the safety components
(Components with this symbol near the circuit board) specified in the safety test documents can be used for
replacement during the maintenance. Ask the manufacurer for components if there are no same components
for replacement.

4
www.i3-learning.com
24. I class equipment can touch conductive parts and the protective earthing of the output socket should be
reliably connected with the protective earthing terminal.
25. Protect the monitor from direct sunlight or other heat sources, place the monitor’s back to the sun so as to
reduce the reflected light.
26. Don’t put the monitor together with magnets, motors, transformers, speakers and monitor.
27. Unplug the power plug and contact the distributor or service center when the monitor has smoke,
abnormal noise or odd smell.
28. Don’t knock or scratch the monitor with any hard objects, don’t touch the screen with the fingers so as to
avoid smears or scratches.

5
i3TOUCH OPTICAL SENSE - operations manual
Basic operation
• On/Off
1. Use 100-240V AC as monitor power supply.
2. Please press the POWER key on the remote control when the monitor screen is not on.
3. Please press the POWER key on the remote control when you want to turn off the monitor temporarily.
4. Please disconnect the power outlet if you want to completely turn off the monitor.
• Auto power off function
1. In monitor/AV mode, the monitor will switch to standby mode automatically if no signal is input in more
than minutes.
2. In PC mode, the monitor will switch to standby mode automatically if it does not word for more than
5 minute.
• Save before shutdown
When PC signal source is used, please set the resolution of PC display card according to below modes;
(1360x768 @60Hz, 1024x768@60Hz, 800x600 @60Hz, 1920x1080@60Hz)
Accessories

6
www.i3-learning.com
Connecting antenna or monitor broadcast networks
Each USB touch connecting cable must be connected
to interactive touch A port first. Then connect
interactive touch B port. If not follow this active, then
touch function will not appear.
Connecting satellite receiver or decoder
To receive the monitor programs of satellite network broadcast,
you must connect a satellite receiver with the LED monitor.
At the same time, you also need to connect a decoder so as to
receive the encoded signals.
Use coaxial cable and connect it to:
• Output socket of the decoder
• Input socket of the monitor antenna
If you want to connect the monitor with satellite receiver (or
decoder) and video camera, follow below steps:
• Connect the satellite receiver (or decorder) with video camera
first
• Then connect the video camera with the LED monitor, or
connect the satellite receiver (or decoder) with the LED
monitor directly.
Installation
monitor

7
i3TOUCH OPTICAL SENSE - operations manual
No. Name Description
1 ( Power ) Switching key between monitor standby and on mode
2
Menu
If the menu hides, press this key to display OSD menu; if the menu displays,
press this key to exit the current menu.
3 Signal source
(monitor/Video)
Switch among all the available input signal sources (monitor, Av1, S-VIDEO,
COMPONENT1, COMPONENT2, HDMI1, HDMI2, VGA, USB)
4
VOL +/-
Adjust the sound output level of the speaker (same function as the
<volume / > key on the remote control). In OSD menu, it is used to
move the cursor leftward or rightward, or change the settings (same func-
tion as the cursor left/right key on the remote control).
5
CH
Select the previous or next channel , (same function as the
<channel / > key on the remote control). In OSD menu, it is used to
move the cursor upward or downward (same function as the cursor up/
down hey on the remote control).
6 Exit (Optional) Exit the menu or return to the previous menu (Some models do not have
this key)
7 Remote control
receive window
Receive the signals sent by remote control.
8 Power indicator A red light indicates it is in standy mode;
A green light indicates it is in working mode
Note: For reference only, please subject to the actual model.
Descriptions for keys of the front panel

8
www.i3-learning.com
No. Name Description
1 HDMI1 Connect to the digital audio/video output terminal of the digital signal source
equipment.
2 HDMI2 Connect to the digital audio/video output terminal of the digital signal source
equipment.
3 SCART Connect them to the Scart video output terminal.
4 PC Audio PC Audio input
5 VGA IN Input terminal for pc
6 SPDIF Digital audio coaxial output
7 HDMI3 Connect to the digital audio/video output terminal of the digital signal source
equipment.
8 USB Multimedia USB, music, pictures and video support.
9 CI CARD CI Signal input
10 EARPHONE Earphone signal output
11 YPBPR Connect every terminal to the component video.
12 AV IN AUDIO L R Video and Audio signal input.
13 AV AUDIO L R Video and Audio signal input (L R).
14 ON/OFF Power on/off
15 POWER SWITCH power
Rear panel interface
1789
10 11 12 13 14
23456
19
20 2122 23 24

9
i3TOUCH OPTICAL SENSE - operations manual
No. Name Description
16 AC OUT AC power input port (80W 2A)
17 SOUND BOX L R Connect the left/right speaker output
18 SW INSIDE OUTSIDE Switch=for the outer speaker, switch-for built-in speakers, switch O off
19 TOUCH1 TOUCH2
TOUCH3
USB1corresponding VGA1;USB2 corresponding VGA2;USB3
correspondingVGA3;The default status is USB1
20 RS232 RS232 Control interface
21 VGA1 Connect to PC D-Sub terminal
22 VGA2 Connect to PC D-Sub terminal
23 VGA3 Connect to PC D-Sub terminal
24 VGAOUT Link to the rest of the display device
Note: For reference only, please subject to the actual model.
Rear panel interface

10
www.i3-learning.com
POWER : Turn the MONITOR on/standby.
MUTE : Press to mute the sound, press again or press VOL+ to unmute.
NUMBER BUTTONS : Choose channel directely. Press number
buttons and press OK button to play the channel.
: Return to the previous channel viewed.
P.MODE : Select the picture mode.
S.MODE : Select the sound mode.
NICAM : Press this key to select simple tone, stereo or bilingual mode/
only when it`s supported by broadcasting system.
SOURCE : Press to display the input source menu.
MENU : System setup menu.
INFO : Display current mode information.
OK : Confirm button for menu.
EXIT : Exit the OSD menu.
Cursor left/right /up/down : Cursor buttons used in menus.
VOL+/- : Press ”VOL+/-”, you can adjust the volume.
ASPECT : Press to see top half of page double size,
Press again to see the bottom half of page double size.
Press again for normal size.
SLEEP : Standby timer.
FREEZE : Holds the current picture.
USB : Multimedia source signal fast switching.
AUTO : Press to change the auto reduction mode.
FAV : Display the favorite program list.
EPG : Press to display EPG information (Electronic Program Guide).
TEXT : Turn off/on the Teletext display.
MIX : Press to display the picture and the teletext at the same time.
HOLD : Hold on or off the current page display.
INDEX : Press to return to the index/initial page.
SIZE : Change the size of display in Teletext mode.
REVEAL : Reveal or Hide the hidden words.
SUBPAGE : Display a sub-page of upper options.
: Open/Close program
: Play/Pause program
: Stop program
: Fast reverse
: Fast forward
: Previous chapter
: Next chapter
AUDIO : In DVD source voice switching.
GOTO : In DVD source press to cycle to a desired position.
REPEAT : Press to change the playing mode.
A-B : Repeat the segment between A and B.
Colour buttons : Short cuts-follow the coloured links.
Handle the remote control with care. Avoid falling off or being trampled or splashed with liquids.
Remote Control

11
i3TOUCH OPTICAL SENSE - operations manual
Press Source button to show source list.
Press button to choose the mode.
Press OK button to enter the mode.
Source List

12
www.i3-learning.com
Press SETUP button to show, Picture, Sound, Time, Lock, Setup menu.
Press OK button to select specific submenu and the adjustable value. In the submenu,
press or button to select menu item.
Programme Edit
Press button to select Programme Edit, and then press OK button to enter menu.
Signal Information
Press button to select Signal Information, and then press OK button to Signal Information.
CI Information
Press button to select CI Information, and then press OK button to see CI Information.
Screen Menu

13
i3TOUCH OPTICAL SENSE - operations manual
Picture Mode
Press to select Picture Mode, and then OK button to enter. Press button to select dynamic/
standard/ personal mode and press or to adjust value.
Colour Temp
Press to select Colour Temp, and then OK button to ener and press button to slect cool/
normal/ warm mode.
Noise Reduction
Press to select Noise Reduction mode, and then OK to enter submenu. You can select off/low/middle/
high/default by pressing button.
Picture Menu

14
www.i3-learning.com
Sound Mode
Press to select Sound Mode, and then OK button, press button to select standard/music/
movie/sports/personal mode.
Balance
Press to select Balance, and then OK button to enter submenu, press button to adjust balance
value.
Surround Sound
Press to select Surround Sound, and then OK button to enter submenu, then press button to
select off/surround mode.
AD Switch
Press to select AD Switch, and then OK button to select on/off, and you can adjust AD volume value by
pressing button when AD switch is set to on.
Sound Menu

15
i3TOUCH OPTICAL SENSE - operations manual
Clock
Press to select Clock, and then OK button to set.
Sleep Timer
Press to select Sleep Timer, and then OK button to enter submenu, and press to select the sleep
timer type.
Auto Standby
Press to select Auto Standby and then OK button to set and select off/3h/4h/5h etc.
Time Zone
Press to select Time Zone, and then OK button to enter submenu, and press or to adjust the
time zone.
Time Menu

16
www.i3-learning.com
Lock System
Press to select Lock System, and then OK button to select on/off to open and close the lock function.
Set Password
Press to select Set Password,and then OK button to input old password 0000° and set new password.
Block Program
Press to select Block Program, and then OK button to enter the submenu and then green button to
choose lock/ unlock mode.
Parental Guidance
Press to select Parental Guidance, and then OK button to select off/4/5/6/7/8 etc.
Lock Menu

17
i3TOUCH OPTICAL SENSE - operations manual
OSD Language
Press to select OSD Language, and then OK button. Press or button to choose language
choices.
TT Language
Press to select TT Language, and then OK button to enter submenu, and then press to select
West/East/ Russian/Arabic/Farsi.
Hearing Impaired
Press to select Hearing impaired, and then OK button to select on/off.
Aspect Ratio
Press to select Aspect Ratio, and then OK button to enter submenu, and then press to select
Auto/4:3/16:9/ Zoom1/Zoom2.
Blue Screen
Press to select Blue screen and OK button to select on/off.
Setup Menu

18
www.i3-learning.com
Press setup button to show Photo, Music, Film, Text. Press button to choose specific menu and the
adjustable value. In the submenu, press or button to choose menu item.
Photo Show
Select C:\, press OK button to enter submenu.
1. Insert USB Port to USB entry.
2. Press to select photo, and then OK button to enter submenu.
3. Select C:\ press OK button to enter submenu
4. Select the specific photo, and press button to play, press button to play previous one, press
to play next one.
5. Press Exit button to exit.
Music Play
Select C:\, press OK button to enter submenu.
1. Insert USB Port to USB entry.
2. Press to select music, and then OK button to enter submenu.
3. Select C:\, press OK button to enter submenu
4. Select the specific music, and press button to play, press button to play previous one, press
to play next one.
5. Press Exit button to exit.
USB Mode

19
i3TOUCH OPTICAL SENSE - operations manual
Select C:\, press OK button to enter submenu.
1. Insert USB Port to USB entry.
2. Press to select film, and then OK button to enter submenu.
3. Select C:\, press OK button to enter submenu
4. Select the specific film, and press button to play, press button to play previous one,
press to play next one.
5. Press Exit button to exit.
Text Show
Select C:\, press OK button to enter submenu.
1. Insert USB Port to USB entry.
2. Press to select text, and then OK button to enter submenu.
3. Select C:\, press OK button to enter submenu
4. Select the specific text, and press button to play, press button to play previous one,
press to play next one.
5. Press Exit button to exit.
Film Play