i3TOUCH E1070T10 User manual

USER MANUAL

Version 1.0 2
Contents
1. Important safety Instructions...……….………………………………………….….3
1.1 Safety precautions
1.2 Maintenance
2. Introduction...……………………..…………………………………………….…....8
3. Product Description.......…..………………………………..…………………….…9
3.1 Front View
3.2 Rear View
4. PC Connection...……………..…..........................................…….………….…12
5. Remote Control..……………..………..……………………………..…………….13
6. Home Menu Description……..….….…………………….……....….…………...14
7. Android Setup Menu Description……..….….……….…….……..….…………...17
8. Product Specification..……..……………….……………………………...………26
9. Product Dimensions…..…….…..……….…………………………….………….28
10. Troubleshooting.…..……….………………………………..………….……..…29
10.1 Product self-Diagnosis
10.2 Before Requesting service

Version 1.0 3
ICON NAME MEANING
Warning Failing to follow the precautions marked with this sign may
result in a serious injury or even a fatality.
Caution Failing to follow the precautions marked with this sign may
result in a personal injury or property damage.
1. Important Safety Instructions
Before operating the product, please read this manual carefully.
CAUTION:
Unauthorized tampering with the inside of the monitor invalidates the warranty.
The manufacturer shall not warrant for any damage caused by improper maintenance and/or repair
work by third parties.
Important safeguards for you and your new product:
Your product has been manufactured and tested with your safety in mind. However, improper use
can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have
been built into your new product, please read and observe the following safety points when
installing and using your new product and save them for future reference.
①PH M8x60l(Natural Color)
②M8 Washer
③M8 Nut
After the products is out of the wrapping paper, grasp the upper handle as shown in the image.
Hold the display with the other hand
The product must be lifted and moved vertically and level..
Do not let the display stand vertically without supporting. The sound bar below the display will not
be able to carry the weight.
WARNING :
To reduce the risk of electric shock do not remove cover (or back). No user serviceable parts inside.
Refer servicing to qualified service personnel. To prevent fire or shock hazard, do not expose the rear
of the set to rain or moisture. Do not rub or strike the LCD screen with anything hard as this may
scratch, mark, or damage the LCD permanently.

Version 1.0 4
1) Read Instructions
2) Follow Instructions
All operating and use instructions should be followed.
3) Retain Instructions
The safety and operating instructions should be retained for future reference.
4) Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
5) Cleaning
Disconnect the unit from the electricity supply before cleaning. Do not use abrasive cleaners. Use a
damp cloth for cleaning.
6) Water and Moisture
Do not use this apparatus near water.
7) Transporting Product
A product and cart combination should be moved with care. Quick stops, excessive force and
uneven surfaces may cause the product and cart combination to overturn.
8) Ventilation
Do not block any of the ventilation openings.
Install in accordance with the manufacturer’s instructions.
9) Power Sources
This product should be operated only from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to your home, consult your supplying dealer.
10) Power Lead Polarization
This product is equipped with a three-wire grounding-type cord. This is a safety feature. Do not
defeat the safety purpose of the grounding-type cord.
11) Power Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles and the point where they exit from the product.
12) Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable
system is grounded so as to provide some protection against voltage surges and built-up static
charges. A “face plate” also needs to be installed with an isolating capacitor to prevent any
damage from static.

Version 1.0 5
13) Lightning
For added protection for this product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent possible damage to the product due to lightning and power-line surges.
14) Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such power lines or circuits. When installing
an outside antenna system, extreme care should be taken to avoid contact with such power lines or
circuits, as contact with them might be fatal.
15) Earthing the product
This product must be earthed properly to comply with the safety regulations in the country of use.
If you are unsure of these regulations, please consult a qualified electrician.
16) Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to
dangerous voltages or other hazards. Refer all servicing to qualified service personnel. If the Set
does not operate properly, switch it off and call your dealer.
17) Damage Requiring Service
Isolate this product from the mains supply and refer servicing to qualified service personnel under
the following conditions:
1. If the power-supply cord or plug is damaged.
2. If the glass front has been damaged.
3. If there is ingress of water between the glass and the LCD screen.
4. If the product does not operate normally by following the operating instructions. Adjust only
those controls that are covered by the operating instructions as an improper adjustment of other
controls may result in damage and will often require extensive work by a qualified technician to
restore the product to its normal operation.
5. If the product has been dropped or the cabinet has been damaged.
6. If the product exhibits a distinct change in performance.
18) Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform
safety checks to determine that the product is in proper operating condition and the front seal is
intact.
19) Mounting
The product should be mounted on a wall only as recommended in the instructions.
20) Power
This set operates on an AC supply; the voltage is as indicated on the label on the Manual. This
appliance must be earthed at all times through the chassis as well as through the power lead.
21) Location
Do not install on an unstable location with support area smaller than the DID SET.
Please secure enough space for safety use.

Version 1.0 6
Products at the same time holding the products when building or product, do not hold the back of the
handle. under the product makes. the handle is a secondary role.
Table stand and put them on the table by using the installation gets the nose does not necessarily
prevent a fall on the floor using the screws fixed.

Version 1.0 7
1-2. Care and Maintenance
External Surface and Screen Maintenance
Clean the product with a soft dry cloth.
• Avoid cleaning the product with an inflammable substance
such as benzene or thinner or with a wet cloth.
This may result in a problem with the product.
• Avoid scratching the screen with your fingernails or a sharp object.
• Avoid cleaning the product by spraying water onto it. If water
enters the product, it may result in fire, electric shock or a
problem with the product.
A white stain may be generated on the surface of the model if
a supersonic humidifier is used near it.
▷The appearance and the color may differ depending on models.
Securing the Installation Space
• Keep the required distances between the product and other objects (e.g. walls) to ensure proper ventilation.
Failing to do so may result in fire or a problem with the product due to an increase in the internal temperature.
Install the product so the required distances shown in the figure are kept.
▷The appearance may differ depending on the product.
When installing the product with a stand When installing the product with a wall-mount
About persistent images
• Displaying a static image for a long time may create a persistent image or stain on the screen. If you do not use
the product for a long time, set the power-saving mode or screen saver.
• Due to technological constraints of the Panel manufacturer, the images generated by this product may appear
either brighter or darker than normal by appr. 1ppm (parts per million) pixel. The number of sub-pixels of an
panel by size:
The number of Sub-Pixels = Max. Horizontal Resolution x Max. Vertical Resolution x 3 Example) If the maximum
resolution is 1920 x 1080, the number of sub-pixels is 1920 x 1080 x 3 = 6,220,800.

Version 1.0 8
2. Introduction
2-1. Package Contents
∙ Unpack the product and check if all of the following contents have been included.
∙ Store the packaging box in case you need to move the product later.
∙ If any items are missing, contact your dealer.
∙ Contact a local dealer to purchase optional items.
70” FHD IR Display
Contents
User Manual
Cable
HDMI Cable Power Cable USB Cable
Accessory
Remote Control Batteries(CR-2025 x 2) PEN x 2

Version 1.0 9
3. Each description
3.1 Front View
①
①Remote Sensor & Power Indicator
When using the remote, aim it directly at this sensor.
- Power ON mode: BLUE
- Power OFF mode: RED
- DPMS mode : RED/BLUE are blanked
• Be sure to point the remote control at the remote control sensor on the
LED/LCD Display

Version 1.0 10
3.2 Rear View
①
②
①7Keys
③
④
Key Description
Power ON / OFF
Menu Display the main screen menu
Source VGA, HDMI1, HDMI 2, EXT.COMPUTER
Vol + Volume Up (Right)
Vol - Volume Down (Left)
▲Move Up
▼Move Down

Version 1.0 11
③Interface
Interface Description
HDMI3 High Definition Multimedia Input- Up To Input
USB For TOUCH External PC Using USB Touch Sensor Connection
RS-232 Facility To Control The Screen Via RS232 Protocol
AUDIO LINE OUT Earphone Or Audio Connection
S/PDIF Optical Connector
MINI YPBPR Component Connection
MINI YPBPR AUDIO
IN Component Audio Connection
AUDIO IN PC Screen Audio Input
VGA PC Screen Input
②Interface
Interface Description
Speaker Out Connected to external speakers
USB 2.0 Download-software update Play contents
USB 3.0 Download-software update Play contents
HDMI 1 High Definition Multimedia Input 1
HDMI 2 High Definition Multimedia Input 2
Display Port DISPLAY PORT Input- up to Input
LAN OUT LAN OUT Ports
LAN IN LAN(Local Area Networks) Ports

Version 1.0 12
④Power
Interface Description
POWER Power on/off
AC IN AC Power In
AC OUT AC Power Out

Version 1.0 13
Notes
: Please turn off the power when connecting external speakers.
: If there are no any sound when connecting to speaker with power-on, please restart it once again
4. PC Connection
1) Connect RGB cable to RGB, Voice connection will be connected to PC AUDIO IN with stereo
cable.
2) HDMI cable will be connected to (display and voice are available at the same time)
3) External speaker will be connected to R , L input with using Ø3.5 stereo cable and then connect
same as below drawing. L, R connection is same. Internal speaker will not output.
Note) Don’t connect NC

Version 1.0 14
5. Remote Controller
5.1 How to insert battery
Key Name Description
POWER Power ON/OFF.
SOURCE Activates OSD menu of input source selecting.
Navigates input source.
PC PC
AV HOME
HDMI HDMI 1, HDMI 2, HDMI 3.
PSM Picture mode: Standard, Dynamic, Soft, User.
SSM Sound mode: Standard, Flat, Music, Movie.
MENU Activates main OSD menu.
EXIT Escapes main OSD menu.
FREEZE Video image freezes.
MUTE Toggles sound status of speaker.
ECO Screen Brightness
SLEEP N/A
INFO Displays input source information.
ZOOM Activates OSD of aspect ratio control.
◀◀ N/A
▶∥N/A
▶▶ N/A
|◀N/A
■N/A
▶| N/A
∧Navigates in main OSD menu.
Navigates input source.
∨Navigates in main OSD menu.
Navigates input source
＞Increases sound volume of speaker. Same as “+ Key” on keypad.
Navigates in main OSD menu.
<Decreases sound volume of speaker. Same as “-Key” on keypad.
Navigates in main OSD menu.
Insert the battery with the + on top.
Battery model:(CR-2025 3V)

Version 1.0 15
6. Home Menu Description
6.1 Menu Overview
On this home menu screen, there are several buttons to change the sources or functions easily.
You can always see the required menu button by touching from the bottom to the bottom of the screen.
i3NOTES
Select the button to use the i3NOTES, writing application equipped on IFPD.
OPS
Shows the OPS screen connected to the product.
HDMI1
Shows the HDMI1 screen connected to the product.
HDMI2
Shows the HDMI2 screen connected to the product.
HDMI3
Shows the HDMI3 screen connected to the product.
DP
Shows the DP screen connected to the product.
VGA
Shows the VGA screen connected to the product.
SETTINGS
To go i3TOUCH Setup

Version 1.0 16
Home Menu
If you drag the bottom of the screen upward, the hidden Home Menu pops up.
With the Home Menu you can go to Brightness, Back, Home, Source, Volume.
Dragging

Version 1.0 17
Home Bar UI Description
Brightness Adjust the brightness.
Back Moves to the previous screen.
Home Go to the home screen.
Source Calls the external input window.
Volume Adjust the volume.
Brightness Back Home Source Volume

Version 1.0 18
7. i3TOUCH Setup Menu Description
7.1 Menu Overview
Select i3TOUCH SETTINGS then you can see the below menu screen
①Network : to setup the Ethernet
②Picture : to setup the brightness, color, and contrast
③Sound : to setup the sound features
④All App : You can go to the apps screen and run CZ file managers and i3 notes.
⑤Advanced : to setup Power option and background image
⑥Restore : to reset the system
⑦System info : to check the system information
⑧Upgrade : to upgrade system F/W
① ② ③ ④
⑤ ⑥ ⑦ ⑧

Version 1.0 19
7.2 Network
Ethernet Setting
To set up the IP automatically by DHCP (Dynamic Host Configuration Protocol) or input the IP
address manually in Static IP setting
DHCP (Dynamic Host Configuration Protocol)
To set up the IP automatically, select DHCP then “Getting IP” messages shows up and it
automatically assigned the IP address. This IP is dynamically assigned so it subject to change.

Version 1.0 20
Static IP
To set up IP address manually by inputting fixed IP. (IP, Netmask, Gateway, DNS)
Network State
To check the current network status of this system. Ethernet, PPOE, WiFi
If it is not connected any network, shows “Unconnected”and shows “Connected” when it
connected to network. Also, IP, Netmark, Gateway, DNS information turns on when connected