IBA X6 User manual

INSTURCTION MANUAL
MODEL: 6 Series
STAND-ALONE
ACCESS CONTROL UNIT
Mode:X6 Model:T6 Model:06
○
1 “#”Button ○ 2“ “Bell Button
The Model 6 Series can support 99 employees with
Proximity Cards or PIN Codes, and it has a back tamper
switch to detect unauthorized attempts at entry.
Dimension:
Model X6:95x58x20mm
Model T6:110x110x20mm
Model 06:120x110x18mm
Technical Specifications
Number Description Specification
1 Rated Operating Voltage DC12V
2 Allowed Operating Voltage Range DC10V-16VDC
3 Static Operating Current 90mA
4 Max Operating Current 150mA
5 Operating Temperature -20˚C -55˚C
6 Operating Humidity 0-95%
LED Display
Mode LED DOOR LED
Occurrence Green Red Green Red
Normal condition Light
Secure condition Light
Enter program ode Light
Release the Lock Light
Tamper Light
Sound Display
Occurrence Sound display Sound Description
Valid Press One short deep deep
Valid change code Three short deeps deep deep deep
Valid Reader One short deep deep
Invalid Code One long deep deep…
Invalid Program One long deep deep…
Setting Instroductions
1.programming Glossary
Menu
Number Menu Description Original
Settings
1 Chang Employee Code1 2580
2 Chang Employee Code2 0000*
3 Chang Program Code 1234
4 Chang Secure Code 3838
6 SetNO/NC and ReleaseTime 10secs
7 Add a Proximity Card or a PIN Code
8 Delete a Proximity Card or a PIN Code
Notice: Input 0000- disable the function to the items you
set above.You must be under normal mode when
changing the functions. All the changed code can’t
be same with the system code.
2. How to enter programming Mode
“#+ Program code ” means in Normal mode, press the
key ‘#’ for two seconds until the door LED turns red, then
input Program code to enter the programming state.
3. Function Settings
zChange User Password 1
‘#’ + Program code + key 1+ x x x x (new 4-digits code)
zChange User Password 2
‘#’ + Program code + key 2+ x x x x (new 4-digits code)
zChange Programming Code
‘#’ + Program code + key 3+ x x x x (new 4-digits code)
zChange Secure Code
‘#’ + Program code + key 4+ x x x x (new 4-digits code)
zSet No/NC and Door Release Time
(NO= Normal Open NC：Normal Close)
‘#’ + Program code + key 6+ x x x x
The first two digits ndicates NO(10)/NC(00)
The last two digits indicates door release time (second)
i.e. 12 indicates 12secs
zAdd a new proximity card or a PIN code
‘#’ + Program code + key 7+ x x x + show the card to
card reading area.
x x x= card number from 01 to 99
Or
‘#’ + Program code + key 7 + x x x x (4-digits PIN code)
Notice: If you want to add more cards, please repeat the
later 2 steps, remember that card number should not be
repeated or the repeated card will be invalid.
http://www.mjicka.com ShenZhen Angetong Technology Co,.Ltd. TEL:[phone]

zDelete a proximity card or a PIN code
‘#’ + Program code + key 8+ x x x + Program Code
x x x= the card number you want to cancel
Or
‘#’ + Program code + key 8 + x x x x (4-digits PIN code
you want to cancel) + Program Code
zReturn To Factory Settings
‘#’ + Program code + key 0 + Program Code
Operations：
How to open door in Normal Mode
› Input Open code 1 to open the door
› Show a valid proximity card to the card reading to
open the door
How to open door in Secure mode
→When the Open code 2 is original code (0000),the
card holders with card numbers 01-10 can use their
cards to open the door.
→When the Open code 2 is changed to a new code,
and then show their cards to open the door.
Notice: In Secure mode, the card holders with card
number after 10 can not open the door.
Replace a lost Program code or Secure code
› Remove power from the controller
› Press the REX button
› Supply power to the unit with REX button pressed
› Release the REX button
› —If the controller is in Normal Mode. You have 15
seconds to set a new Program code into the unit the
original code 1234, before the controller returns to the
exiting code.
-- If the controller is in Secure mode, you have 15
seconds to return to the Normal mode bu inputting 3838
+ #. Then you can set your new Secure code by
Inputting # +Program code + key 4 +x x x x (new
Program code)
Wiring
Controller without Bell
Lock strike: connect different locks to different terminals
--Fail safe Lock strike link to NC
-- Fail Secure Lock strike link to NO
Controller with Bell
Lock strike--Fail safe Lock strike : “-” + NO
--Fail SecureLock strike : “-” +NC
You can set Lock strike type through controller or wiring.
Common Requirements：
Power Supply:
Output Voltage 12V, with bell control
Door Bell: If the power supply can not support the bell,
you could install a bell without power.
http://www.mjicka.com ShenZhen Angetong Technology Co,.Ltd. TEL:[phone]
For more application information please visit our website http://www.mjicka.com