C Prox Ltd DPN-2 User manual

1
C Prox Ltd (inc Quantek)
59 Sheffield Road, Dronfield, S18 2GF
[phone] [email protected] www.quantek.co.uk
Keypad & Reader Access Control
DPN-2
User Manual
Contents
1. Packing List ................................................................................................................................................. 2
2. Description .................................................................................................................................................. 2
3. Features ...................................................................................................................................................... 2
4. Specification ............................................................................................................................................... 3
5. Installation .................................................................................................................................................. 3
6. Wiring ......................................................................................................................................................... 3
7. Soun an light in ication .......................................................................................................................... 4
8. Quick programming gui e .......................................................................................................................... 4
8.1 A ministrator settings (master co e, manager car s, anti- uress, etc) ......................................... 4
8.2 User setting for Zone 1 (a / elete users, oor opening mo e, relay time, etc) .......................... 4
8.3 User setting for Zone 2 (a / elete users, oor opening mo e, relay time, etc) ......................... 5
8.4 System settings (working mo e, facility co e, Wiegan format, transmission co e, etc) ............. 5
8.5 User optional settings (keypa tone, backlight mo e, LED mo e, etc) .......................................... 5
9. Full programming gui e.............................................................................................................................. 6
Programming a vice ................................................................................................................................... 6
9.1 A ministrator settings (master co e, manager car s, anti- uress, etc) ......................................... 6
9.2 User Settings for Zone 1 (a / elete users, oor opening mo e, relay time, etc) ........................ 7
9.3 User Settings for Zone 2 (a / elete users, oor opening mo e, relay time, etc) ........................ 8
9.4 System settings (working mo e, facility co e, Wiegan format, transmission co e, etc) ............. 8
9.5 User optional settings (keypa tone, backlight mo e, LED mo e, etc) .......................................... 9
10. User operation ...................................................................................................................................... 10
11. Alarm functions ..................................................................................................................................... 10
12. Multi working mo es (information an setup) .................................................................................... 10
12.1 Wiegan rea er mo e ................................................................................................................... 10
12.2 Stan alone for single oor ............................................................................................................ 11
12.3 Stan alone for two oors .............................................................................................................. 11
12.4 With external rea er for two oors .............................................................................................. 11
12.5 Two units interlocke for two oors ............................................................................................. 11
12.6 Anti-passback for single oor ........................................................................................................ 12
12.7 Anti-passback for two oors .......................................................................................................... 12
13. Wiring iagrams for all 7 multi working mo es.................................................................................... 12
14. Troubleshooting .................................................................................................................................... 15
15. Reset to factory efault ........................................................................................................................ 15
16. Issue recor ........................................................................................................................................... 15

2
1. Packing ist
Name Quantity Remarks
Keypa 1 DPN-2
User manual 1
Screw river 1 Φ20mm×60mm, special for keypa
Rubber plug 2 Φ6mm×30 mm, use for fixing
Self tapping screws 2 Φ4mm×27 mm, use for fixing
Dio e 1 IN4007
Please ensure that all the above contents are correct. If any are missing please notify us
imme iately.
2. Description
DPN-2 is an access control keypa an proximity rea er for up to two oors. It supports car , pin, car +pin
access.
It has 2 relays to control 2 oors an supports up to 2000 users in total, each user can possess one car
an one pin. It can irectly rive a lock, alarm, oorbell, an can also connect with an exit button an oor
contact.
There are 7 working mo e with this evice:
1. Wiegan rea er.
2. Stan alone for single oor.
3. Stan alone for two oors.
4. With external rea er for two oors.
5. Two units interlocke for two oors.
6. Anti-passback for single oor.
7. Anti-passback for two oors.
In a ition, it also supports 1 master co e, 2 manager car s, 2 anti- uress car users, an 2 anti- uress PIN
users, provi ing users with easy operations an goo reliability.
3. Features
•Strong zinc alloy casing.
•Waterproof, conforms to IP68.
•Digital backlit keys. The back light can be set to normally on, normally off, or human approach on.
•Anti-tamper alarm, oor contact alarm an anti- uress alarm functions.
•A an elete users quickly with manager car s.
•Can a an elete users via the keypa .
•Multiple working mo es to suit most applications.
•Up to 2000 users.
•A justable oor output, alarm an oor open times.
•Stan alone or Wiegan .
•Re , yellow & green LEDs isplay working status.
•Easy to install an program.

3
4. Specification
Operating voltage 12-24Vac/ c
User capacity 2000
Car rea ing istance 3-6 cm
Car frequency 125KHz EM
Active current <60 mA
I le current <25 mA
Lock output loa <1A
Alarm output loa <1A
Operating temperature -45 to 55⁰C
Operating humi ity 0% to 95%
Waterproof Conforms to IP68
5. Installation
•Remove the back cover from the keypa using the supplie special screw river.
•Use the back cover or the template to mark an rill 2 fixing holes an 1 cable hole.
•Put the supplie rubber wall plugs into the 2 fixing holes.
•Fix the back cover firmly on the wall with the 2 self-tapping screws.
•Threa the cable through the cable hole.
•Attach the keypa to the back cover.
6. Wiring
ZONE 2 (Upper socket) ZONE 1 ( ower Socket)
No.
Marks Colour Description Marks Colour Description
1 BELL_A Pink Doorbell button D0 Green Wiegan output D0
2 BELL_B Pink Doorbell button D1 White Wiegan output D1
3 ALARM+ Re Alarm ano e AC1 Re AC1 (+12/24V)
4 AC2 Black AC input GND Black GND
5 OPEN2 Yellow Exit button OPEN1(LED) Yellow Exit button
6 D_IN2 Brown Door contact D_IN1(BZ) Brown Door contact
7 ALARM2- Grey Alarm 2 ALARM1- Grey Alarm 1
8 NO2 Blue Relay 2 NO NO1 Blue Relay 1 NO
9 COM2 Purple Relay 2 COM COM1 Purple Relay 1 COM
10 NC2 Orange Relay 2 NC NC1 Orange Relay 1 NC

4
7. Sound and light indication
Operation ED Color Buzzer
Stan by Re flash
Press key Di
Rea car Green Di-
Door 1 open Green Di-
Door 2 open Green flash Di-
Operation successful Green Di-
Operation faile DiDiDi
PIN inputting Re
Car
&
PIN
r
ea ing
Re
Multi Car
r
ea ing
Re
Un er menu Re
Un er setting Orange
Manager car enter Orange DiDi
Manager car exit Re flash Di-
Alarm Re quick flash Alarm
8. Quick programming guide
8.1Administrator settings
Standby Master
code
Menu Setting Remarks Functions
Re flash Re Re Orange
* Master
co e#
00 New master co e# Repeat new master co e#
(Note: Co e length 6-8 igits)
Factory efault:
999999
Change the master co e
01 Rea manager a car Default: Zone 1 Set manager a car
02 Rea manager elete car Set manager elete car
03 Rea anti- uress car (Zone 1) Set Zone 1 anti- uress car
04 Rea anti- uress car (Zone 2) Set Zone 2 anti- uress car
05 Anti- uress PIN# (Zone 1) Set Zone 1 anti- uress PIN
06 Anti- uress PIN# (Zone 2) Set Zone 1 anti- uress PIN
07 0000# Both zones Delete all users
51 Master open Lock 1
52 Master open Lock 2
8.2User setting for Zone 1
Standby Master
code
Menu Setting Remarks Functions
Re flash Re Re Orange
* Master
co e#
11
Rea car Users can be a e
continuously without
exiting programming
mo e
To a car users
User ID number# Rea car
Car number#
User ID number# Car number#
User ID number# PIN# To a PIN users
12
Rea car Users can be elete
continuously without
exiting programming
To elete users User ID number#
Car number#
13
0#
Default: 2
Entry by car
1# Entry by car + PIN
2# Entry by car or PIN
14 0-99# Default: 5 Set oor relay time
15 0# Default: 0 Relay setting pulse mo e
1# Relay setting toggle mo e
16 1-10# Default: 1
Car mo e only
To set oor open by multi
car s
17 User ID number# Car number# Car
quantity#
To a a series of
consecutive car s
See section 10.5 for assigning a PIN to a registere car user. Default ‘ol ’ PIN is 1234.

5
8.3User setting for Zone 2 (The unit must be in two door mode to change these settings)
Standby Master
code
Menu Setting Remarks Functions
Re flash Re Re Orange
* Master
co e#
21
Rea car Users can be a e
continuously without
exiting programming
mo e
To a car users
User ID number# Rea car
Car number#
User ID number# Car number#
User ID number# PIN# To a PIN users
22
Rea car Users can be elete
continuously without
exiting programming
To elete users User ID number#
Car number#
23
0#
Default: 2
Entry by car
1# Entry by car + PIN
2# Entry by car or PIN
24 0-99# Default: 5 Set oor relay time
25 0# Default: 0 Relay setting pulse mo e
1# Relay setting toggle mo e
26 1-10# Default: 1
Car mo e only
To set oor open by multi
car s
27 User ID number# Car number# Car
quantity#
To a a series of
consecutive car s
See section 10.5 for assigning a PIN to a registere car user. Default ‘ol ’ PIN is 1234.
8.4System settings
Standby Master
code
Menu Setting Remarks Functions
Re flash Re Re Orange
* Master
co e#
30 0-15# Default: 0 To set facility co e
31
0#
Factory efault: 1.
When evice reset to factory
efault, the setting is still vali
Wiegan rea er
1# Stan alone for single oor
2# Stan alone for two oors
3# With external rea er for two oors
4# Two units interlocke for two
oors
5# Anti-passback for single oor
6# Anti-passback for two oor
32 26-37# Default: 26 To set Wiegan format
33 0-2# When evice reset to factory
efault, the setting is still vali
To set keypa transmission format
34 1-3# Default: 1 To set alarm time
35
0#
Safe mo e. Default: 0
Normal mo e
1# Dea mo e
2# Alarm mo e
8.5User optional settings
Standby Master
code
Menu Setting Remarks Functions
Re flash Re Re Orange
* Master
co e#
41
0#
Default: 1
Buzzer will be silence except when in programming
mo e
1# Buzzer will soun when keys are presse
42
0#
Default: 2
Disable keypa backlight
1# Enable keypa backlight
2# Automatic mo e. Normally it is off (sleeping mo e), but
wakes up with human approach
43 0# Default: 1 LED light isable in stan by status
1# LED flash when in stan by status

6
9. Full programming guide
Programming advice
•Master co e must be 6-8 igits. Anti- uress PIN must be 8 igits. User PIN must be 4-6 igits. The
first igit of user PIN an anti- uress PIN in Zone 1 must be 1; in Zone 2 it must be 2.
•User ID number is any number between 1 & 2000. Invali 0’s can be omitte .
•Car numbers must be 8 or 10 igits, if the car number is less than 8 or 10 igits, input 0 before
the car number.
•Door open time is 0-99 secon s. 0=50mS.
•When registering one car user onto the evice, the evice will automatically generate a PIN 1234,
this PIN can’t open the oor, it is use to assign a PIN to the user if nee e .
•When an invali master PIN is entere , the evice will go back to stan by after 5 secon s.
•In operating the keypa , pressing # means to confirm the input of the PIN. In operation of a cycle
a ing or eleting car s, pressing # means to en the cycle an backup the operation. Pressing *
means to exit the operation.
•Working mo e an keypa transmission format have been set before shipping. The customer can
change these settings accor ing to their requirements, but when the evice is reset to factory
efault the setting is still vali .
•When users of Zone 1 are successfully registere , the LED will turn green; when users of Zone 2 are
successfully registere , the LED will flash green.
9.1Administrator settings
9.1.1 Enter into programming mode
.*. .Master code. .#. Default master co e is 999999
All the steps below must be one after entering into programming mo e.
9.1.2 Change the master code
.00. .New master code. .#. .New master code. .#.
Master co e must be 6-8 igits.
9.1.3 Set manager cards
Set manager add card
.01. .Read manager add card.
Set manager delete card
.02. .Read manager delete card.
Note: When a ing new manager car s, the new one will automatically overwrite the ol car . Default Zone 1.
9.1.4 Set anti-duress cards
Set anti-duress card for Zone 1
.03. .Read anti-duress card.
Set anti-duress card for Zone 2
.04. .Read anti-duress add card.
Note: When a ing new anti- uress car s, the new one will automatically overwrite the ol car .
9.1.5 Set anti-duress PIN
Set anti-duress PIN for Zone 1
.05. .8-digit duress PIN. .#.
Set anti-duress PIN for Zone 2
.06. .8-digit duress PIN. .#.
Note: The first igit must be 1 for Zone 1; the first igit must be 2 for Zone 2.
When a ing a new anti- uress PIN, the new one will automatically overwrite the ol PIN.
9.1.6 Delete all users
.07. .0000. .#.
Note: Both Zone 1 an Zone 2 users will be elete .

7
9.1.7 Administrator open locks
Administrator open lock 1
.51.
Administrator open lock 2
.52.
9.2User Settings for Zone 1
9.2.1 Read card to add user
.11. .Read card. … .Read card. .#.
Note: Multiple car users can be a e continuously without exiting programming mo e. The user ID number will be
automatically generate for this metho .
9.2.2 Use ID number and read card to add user
.11. .ID number. .#. .Read card. … .ID number. .#. .Read card. .#.
9.2.3 Use card number to add user
.11. .Card number. .#. … .Card number. .#.
Note: Car number must be 8 or 10 igits, if it is less then input a 0 before. The user ID will be automatically generate
for this metho .
9.2.4 Use ID number and card number to add user
.11. .ID number. .#. .Card number. .#. … .ID number. .#. .Card number. .#.
A ing a car user will automatically generate one ‘1234’ PIN. This PIN can’t open the oor, it’s
only for the user to mo ify the PIN. See section 10.5 (page 10) for more information.
9.2.5 User manager card to add card user
.Read manager add card. .Read user card. … .Read manager add card.
9.2.6 Use ID number and PIN to add user
.11. .ID number. .#. .PIN. .#. … .ID number. .#. .PIN. .#.
Note: The PIN is any 4-6 igits. The 1
st
igits must be 1 for Zone 1, with the exception of 1234 which is reserve .
9.2.7 Read card to delete user
.12. .Read card. … .Read card. .#.
9.2.8 Use ID number to delete user
.12. .ID number. .#. … .ID number. .#.
9.2.9 Use card number to delete user
.12. .Card number. .#. … .Card number. .#.
9.2.10 User manager card to delete card user
.Read manager delete card. .Read user card. … .Read manager delete card.
9.2.11 Delete all users
.07. .0000. .#.
Note: Both Zone 1 an Zone 2 will be elete .
9.2.12 Set door opening mode
Entry is by card only
.13. .0. .#.
Entry is by card and PIN together
.13. .1. .#.

8
Entry is by card or PIN (factory default)
.13. .2. .#.
9.2.13 Set door relay time
.14. .0-99. .#.
Note: Door relay time is 0-99 secon s, factory efault is 5.
9.2.14 Set door relay mode
Pulse mode
.15. .0. .#.
The relay will operate for the pre-set pulse time every time it receives a vali car /PIN
Toggle mode
.15. .1. .#.
The relay changes state every time it receives a vali car /PIN an will not change back until it receives
another.
9.2.15 Set door opening by multiple cards
.16. .1-10. .#.
Note: The oor will only open after rea ing all vali multi car s up to the car quantity setting (1-10). It is only for car
entry mo e an the efault is 1.
9.2.16 Add a series of consecutive card users
.17. .ID number. .#. .Card number. .#. .Card quantity. .#.
Note: The car numbers must be consecutive. Car quantity is 1-2000, car number 8 or 10 igits.
9.3User Settings for Zone 2
The metho is the same as Zone 1, except the correspon ing menu shoul be 21, 22, 23, 24, 25, 26
& 27. The unit must be set in 2 oor mo e to e it Zone 2 user settings.
9.4System settings
9.4.1 To set facility code
.30. .0-15. .#.
Note: Co e shoul be 0-15, factory efault is 0.
9.4.2 Setting working mode (see section 12 on page 10 for more details on each mode)
To set as Wiegand reader
.31. .0. .#.
To set as standalone for single door (factory default)
.31. .1. .#.
To set as standalone for two doors
.31. .2. .#.
To set as with external reader for two doors
.31. .3. .#.
To set as two units interlocked for two doors
.31. .4. .#.
To set as anti-passback for single door
.31. .5. .#.
To set as anti-passback for two door
.31. .6. .#.

9
9.4.3 To set Wiegand format
.32. .26-37. .#.
Note: Factory efault is 26
9.4.4 To set keypad transmission format
.33. .0-2. .#.
Note: Keypa transmission format is 0, 1 or 2, factory efault is 0. When the evice is factory reset, the setting remains
vali . See section 12.1 (pages 10 & 11) for more etails.
9.4.5 Setting the alarm time
.34. .1-3. .#.
Note: Factory efault is 1 minute. When the evice is factory reset, the setting remains vali .
9.4.6 Setting the safe mode
Normal mode (factory default)
.35. .0. .#.
Dead mode
.35. .1. .#.
If an invali car or PIN in inputte 10 times in 10 minutes, the system will be ea for 10 minutes.
Alarm mode
.35. .2. .#.
If an invali car or PIN in inputte 10 times in 10 minutes, external alarm an built-in buzzer are activate .
9.5User optional settings
9.5.1 Setting keypad tone off or on
Off mode
.41. .0. .#.
The evice will be silent except when in programming mo e.
On mode (factory default)
.41. .1. .#.
The evice will emit a tone every time a key is presse .
9.5.2 Setting keypad back light
Off mode
.42. .0. .#.
On mode
.42. .1. .#.
Automatic mode (factory default)
.42. .2. .#.
Normally the back light is off (sleeping mo e) but wakes up with human approach.
9.5.3 Setting ED light (standby status)
Disable ED light
.43. .0. .#.
Flashing ED light (factory default)
.43. .1. .#.

10
10.User operation
10.1 Entry by card (when multi card quantity is set to 1, factory default)
Rea user car , oor will be unlocke
10.2 Entry by card (when multi card quantity is set to 2-10)
Rea user car s one by one within 5 secon s of each other, up to the require quantity, oor will
be unlocke .
10.3 Entry by card and PIN
Present car , then enter PIN (4-6 igits) followe by #. The oor will unlock.
10.4 Entry by card or PIN mode
Present car or enter PIN (4-6 igits) followe by #. The oor will unlock.
10.5 Modify user PIN (no need to enter programming)
.*. .Read card. .Old PIN. .#. .New PIN. .#. .New PIN. .#. (The ‘ol ’ PIN for newly generate car users is 1234)
Or .*. .User ID number. .#. .Old PIN. .#. .New PIN. .#. .New PIN. .#. (If alrea y mo ifie from 1234)
11.Alarm functions
11.1 Anti-tamper alarm
If the evice is isassemble illegally, the external alarm an built-in buzzer will operate.
11.2 Door contact alarm
When wire to a oor contact, if the oor is opene illegally, the external alarm an built in buzzer
will operate.
11.3 Anti-duress alarm
When an anti- uress car /PIN is etecte , the correspon ing lock will still open but the external
alarm will operate. The built-in buzzer will not operate.
11.4 Removing the alarm
Rea a vali user car , manager car or input the master co e to switch the alarm off. The alarm
will also automatically switch off after 1 minute.
12.Multi working modes
12.1Wiegand reader mode
In this mo e, the DPN-2 works as a rea er, connecte with a common access controller. It has the
following functions:
•Mo ify master co e
•Set facility co e
•Set the car transmission format
•Set the keypa transmission format
•Set optional settings
•Anti-tamper alarm
When LED level is low, the in icator light (LED) will turn green. After 30 secon s or LED level rising,
LED will be back to normal. When BZ level is low, the buzzer will beep. After 30 secon s or BZ level
rising, the buzzer will be back to normal.
When use as a rea er, both the car number an keypa transmits in Wiegan format. The output
ata is shown by the low level of D0 & D1 wires:
D0: Low level means 0, green wire
D1: Low level means 1, white wire
The pulse wi th of low level is 100uS
, bit perio is 1.6mS.

11
The igits of the car number can be set to 26-37 bit, an shoul be matche with the controller.
(Factory efault is 26Bit)
Keypa transmission can be set in the following 3 mo es:
Mode 0: Virtual card number
The unit will transmit the PIN ata when it receives the last key (#) press after the PIN co e.
Format: Decimal car number with 10 igits; facility co e (1
st
- 4
th
igit) + PIN co e (5
th
– 10
th
igit).
Example - Facility co e: 15, PIN co e: 9999
Press 9999#, the output format will be 0015009999
PIN co e: 999999
Press 999999#, the output format will be 0015999999
Mode 1: 4 Bit Mode 2: 8 Bit
The output ata is transmitte in the
following format after every key is
presse :
The output ata is transmitte in the
following format after every key is
presse :
12.2Standalone for single door
In this mo e, the evice supports connecting an external car for exiting the oor.
The users of Zone 1 or external rea er can open the oor by vali car or PIN.
12.3Standalone for two doors
In this mo e, users can control two oors in epen ently. Rea a vali car or input a vali PIN for
Zone 1 an oor 1 will open. Rea a vali car or input a vali PIN for Zone 2 an oor 2 will open.
Note: The common car for Zone 1 an Zone 2 can only open oor 1.
12.4With external reader for two doors
In this mo e, this unit is for opening oor 1, the external rea er is for opening oor 2.
Rea vali car or input vali PIN for Zone 1 on this unit, oor 1 will open; rea vali car or input
pin on Zone 2 of external rea er, oor 2 will open.
12.5Two units interlocked for two doors
The interlock function is mainly use in banks, prisons an other places where a higher level of
security is require . When oor 2 is close , rea a vali car /input PIN on this evice, oor 1 will
open; when oor 1 is close , rea vali car /input PIN on external rea er, oor 2 will open.
Note: The vali car /PIN is only for Zone 1, users of Zone 2 are invali .
key Output in hex Output in Binary
0 0 0000
1 1 0001
2 2 0010
3 3 0011
4 4 0100
5 5 0101
6 6 0110
7 7 0111
8 8 1000
9 9 1001
* A 1010
# B 1011
key Output in hex Output in Binary
0 0 11110000
1 1 11100001
2 2 11010010
3 3 11000011
4 4 10110100
5 5 10100101
6 6 10010110
7 7 10000111
8 8 01111000
9 9 01101001
* A 01011010
# B 01001011

12
12.6Anti-passback for single door
In this mo e, this unit is installe outsi e an is for entering the oor. An external rea er is
installe insi e for exiting the oor.
The users can only enter when a vali car is rea on the outsi e evice, an exit when a vali car
is rea on the insi e rea er. Without first rea ing a car on the external evice, the users cannot
exit from the insi e rea er. Also, users can’t enter twice without first exiting on the internal rea er.
Note: This is only for car users of Zone 1, PIN users of Zone 1 an all users of Zone 2 are invali .
12.7Anti-passback for two doors
In this mo e, this unit is installe on oor 1 an is the anti-passback master unit. An external rea er
is installe on oor 2, an is the anti-passback auxiliary unit. Then they buil up a two oor anti-
passback system, often use in parking lot installations.
The users can only enter through oor 1 when a vali car is rea on this unit, an then exit
through oor 2 when a vali car is rea on the external rea er. Without entering a recor on oor
1, the users cannot exit through oor 2. Also, the users can’t enter twice without first exiting
through oor 2.
Note: This is only for car users of Zone 1, PIN users of Zone 1 an all users of Zone 2 are invali .
13. Wiring diagrams for all 7 working modes

13

14

15
14.Troubleshooting
Co e Fault Fault cause Solutions
1 Close rea range Quality of car Use original car s
2 Problem in PIN
setting
PIN is not stan ar First number of the PIN shoul be 1 or 2 to match with the
zone number. PIN shoul n’t be 1234. PIN is 4 to 6 igits.
3 PIN oesn’t open
the oor
Using PIN 1234 1234 is the original PIN & can’t open the oor. It shoul be
mo ifie to another PIN. Set oor opening mo e to car or
PIN.
4 Alarms in normal
con itions
When installe , light leaks
un er the bottom of the unit
Device shoul be installe flush to the wall.
5 No response after
car rea ing
Unit is not in rea y (stan by)
mo e
Press * key, until the re LED starts flashing.
6 Keypa light is
not bright
Mo e of keypa light setting is
wrong
Set keypa light as on or auto in user option settings.
7 Can’t enter
programming
mo e
Forget the master co e Reset to factory efault, master co e will be 999999. Only
installer ata is restore , user ata is unaffecte .
15.Reset to factory default
Disconnect power from the unit.
Press an hol # key whilst powering the unit back up.
On hearing two ‘Di’ soun s, release the # key, system is now back to factory efault
16.Issue record
Site:
Door 1 ocation:
ID number User name PIN Car number Issue ate
Please note it is always best to keep a igital copy of the issue recor , especially on installations with over 10 users.
Site:
Door
2
ocation:
ID number User name PIN Car number Issue ate