IBASE Technology IB885 User manual

IB885
AMD Sempron™ 200U/ 210U
3.5-inch Embedded Board
USER’S MANUAL
Version 1.0

ii IB885 User’s Manual
Acknowledgments
Award is a registered trademark of Award Software International,
Inc.
PS/2 is a trademark of International Business Machines
Corporation.
AMD Sempron™ 200U/210U are registered trademarks of AMD
Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.

IB885 User’s Manual iii
Table of Contents
Introduction.......................................................1
Product Description.............................................................1
Checklist..............................................................................2
IB885 Specifications...........................................................3
Board Dimensions...............................................................4
Installations.......................................................5
Installing the Memory.........................................................6
Setting the Jumpers .............................................................7
Connectors on IB885.........................................................11
BIOS Setup.......................................................21
Drivers Installation......................................39
SM Bus Controller Driver Installation..............................40
VGA Drivers Installation ..................................................43
Realtek Codec Audio Driver Installation..........................45
LAN Drivers Installation...................................................46
Appendix...........................................................49
A. I/O Port Address Map...................................................49
B. Interrupt Request Lines (IRQ)......................................50
C. Watchdog Timer Configuration....................................51

iv IB885 User’s Manual
This page is intentionally left blank.

INTRODUCTION
IB885 User’s Manual 1
Introduction
Product Description
The IB885 3.5-inch embedded board incorporates the Mobile AMD M690E
Express Chipset for Embedded Computing, consisting of the AMD M690E
(North Bridge) and SB600 (South Bridge), an optimized integrated graphics
solution with an 800MHz front-side bus. Dimensions of the board are 102mm x
148mm.
The M690E integrates an ATi Radeon X1200-based graphics engine supporting
dual display, an LVDS interface, an integrated TMDS controller, and operates at
core speeds of up to 400 MHz. IB885 features a low-power design, is validated
with the AMD Sempron™. With one DDR2 800MHz SODIMM socket on
board, the board supports up to 2GB of DDR2 system memory.
The main features of the board are:
Supports AMD Sempron™ 200U (8W, 1.0G, DDR2-400) / 210U
(15W 1.5G, DDR2-667), 256K cache
Supports up to 800MHz FSB
One DDR2 SDRAM SODIMM; Max. 2GB memory
2x Realtek PCI-Express Gigabit LAN
AMD M690E Express VGA for CRT / LVDS / DVI
1x SATA, 4x USB 2.0, 2x COM, Watchdog timer
Digital I/O, LPC/Smart battery interface

INTRODUCTION
Checklist
Your IB885 package should include the items listed below.
•The IB885 embedded board
•This User’s Manual
•1 CD containing chipset drivers and flash memory utility
•Cables and heatsink (shown below) is optional.
ATA Serial
COM2
COM 1
H.R
H.R
2 IB885 User’s Manual

INTRODUCTION
IB885 User’s Manual 3
IB885 Specifications
Features
ySupports AMD Sempron 200U / 210U Processors
800MHz FSB, 1GHz~1.5GHz speed
yDDR2 SODIMM x 1, supports. 2GB Max.
yDual Realtek RTL8111C PCI-E Gigabit LAN
yAMD M690E built-in Radeon X1200 graphics,
DVI on board, Dual display supported
y2x COM, 4x USB, 1x SATAII
System
CPU AMD Sempron processors
1GHz ~ 1.5GHz, 800MHz FSB
System Memory DDR2 SODIMM x 1, Max. 2GB, 400MHz/667MHz
System Chipset AMD M690E + SB600
BIOS Award
Watchdog Timer 256 levels
SSD CF socket
H/W Monitor Yes
Expansion Slot None
Graphics
VGA Controller AMD M690E built-in Radeon X1200 graphics
Supports DVI edge connector and CRT via pin header
Dual Display Available in combination of Analog/CRT, LVDS, onboard
DVI, CRT via pin header
Ethernet
Controller Dual Realtek RTL 8111C PCI-E Gigabit LAN
Connector RJ-45 on board
Multi I/O
Chipset Winbond W83627EHG
1x IDE, 1x KB, 1x Mouse
1x RS232,1XRS232/422/485, 1x SATAII
USB 2 ports on board
Pin header for 2 ports (USB 2.0)
Audio Chipset built-in audio w/ ALC662 codec for 5.1CH
Others 12V DC-in, DC backlight control, smart battery interface
Mechanical and Environmental
Dimensions 102mm x 148mm (4” x 5.8”)
Operating Temperature 0°C~60°C (32°F~140°F)
Storage Temperature -20°C~80°C (-4°F~176°F)
Relative Humidity 10%~90% (non-condensing)

INTRODUCTION
[
Board Dimensions
Top View
4 IB885 User’s Manual

INSTALLATIONS
IB885 User’s Manual 5
Installations
This section provides information on how to use the jumpers and
connectors on the IB885 in order to set up a workable system. The topics
covered are:
Installing the Memory ........................................................................... 6
Setting the Jumpers................................................................................ 7
Connectors on IB885........................................................................... 11

INSTALLATIONS
Installing the Memory
The IB885 board supports one DDR2 memory socket that can support
up to 2GB memory, DDR2 400/533/667 (w/o ECC function).
Installing and Removing Memory Modules
To install the DDR2 modules, locate the memory slot on the board and
perform the following steps:
1. Hold the DDR2 module so that the key of the DDR2 module aligns
with that on the memory slot. Insert the module into the socket at a
slight angle (approximately 30 degrees). Note that the socket and
module are both keyed, which means that the module can be installed
only in one direction.
2. To seat the memory module into the socket, apply firm and even
pressure to each end of the module until you feel it slip down into the
socket.
3. With the module properly seated in the socket, rotate the module
downward. Continue pressing downward until the clips at each end
lock into position.
4. To remove the DDR2 module, press the clips with both hands.
6 IB885 User’s Manual