IBM eserver pSeries 690 User manual

pSeries 690
Installation Guide
SA38-0587-05
ERserver


pSeries 690
Installation Guide
SA38-0587-05
ER s e r v e r


Sixth Edition (January 2004)
Before using this information and the product it supports, read the information in “Safety Notices” on page vii,
Appendix B, “Environmental Notices,” on page 107, and Appendix C, “Notices,” on page 113.
A reader’s comment form is provided at the back of this publication. If the form has been removed, address
comments to Information Development, Department H6DS-905-6C006, 11501 Burnet Road, Austin, Texas
78758-3493. To send comments electronically, use this commercial internet address: [email protected]. Any
information that you supply may be used without incurring any obligation to you.
© Copyright International Business Machines Corporation, 2001, 2004. All rights reserved.
Note to U.S. Government Users -- Documentation related to restricted rights -- Use, duplication or disclosure is
subject to restrictions set forth is GSA ADP Schedule Contract with IBM Corp.

Contents
Safety Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Rack Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Electrical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Laser Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix
Laser Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix
Data Integrity and Verification . . . . . . . . . . . . . . . . . . . . . . . . . . .xi
About This Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
ISO 9000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
Highlighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
Accessing Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
References to AIX Operating System . . . . . . . . . . . . . . . . . . . . . . . . . xiii
Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv
Chapter 1. Reference Materials . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Documentation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Chapter 2. Installing the pSeries 690 . . . . . . . . . . . . . . . . . . . . . . . . .7
Minimum System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Multiple System Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Prerequisites to Installing the pSeries 690 . . . . . . . . . . . . . . . . . . . . . . . .8
Weight Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Step 1. Unpack the pSeries 690 . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Step 2. Check the Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Primary Rack Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Secondary Rack Inventory (If Ordered) . . . . . . . . . . . . . . . . . . . . . . . .9
Step 3. Position and Level the PrimaryRack . . . . . . . . . . . . . . . . . . . . . . .10
Step 4. Attach and Cable Secondary Rack (If Ordered) . . . . . . . . . . . . . . . . . .11
Connecting Internal Power Cords for the Secondary Rack . . . . . . . . . . . . . . . .13
Connecting I/O Cables for the Secondary Rack . . . . . . . . . . . . . . . . . . . .14
Connecting the Integrated Battery Feature Power for the Secondary Rack . . . . . . . . . .15
Step 5. Affix the MCM/L3/Passthrough Plug Map to the Right Frame Extender . . . . . . . . . .16
Using the Map Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Step 6. Observe this Safety Notice During Installation . . . . . . . . . . . . . . . . . . .16
Step 7. Check the Cables and Connect I/O Devices . . . . . . . . . . . . . . . . . . . .17
Step 8. Verify that the Unit Emergency Power Off (UEPO) Switch is in the Off Position . . . . . . .17
Computer Room Emergency Power Off (EPO) . . . . . . . . . . . . . . . . . . . . .17
Step 9. Check the Outlets and the Power Source . . . . . . . . . . . . . . . . . . . . .18
Step 10. Connect and Route the Power Cords to the pSeries 690 . . . . . . . . . . . . . .20
Step 11. Verify the Hardware Management Console (HMC) Installation . . . . . . . . . . . . .22
Connecting to a 128-Port Serial Adapter . . . . . . . . . . . . . . . . . . . . . . .23
Step 12. Turn on the IBF Breaker (If Present) . . . . . . . . . . . . . . . . . . . . . .24
Step 13. Have the Customer Activate the Designated Circuit Breakers . . . . . . . . . . . . .24
Step 14. Install the Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Install the Front Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Install the Rear Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Step 15. Go to Verifying the Hardware Operation . . . . . . . . . . . . . . . . . . . . .26
Completing the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Complete the Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . .26
Leave this Document with your Customer . . . . . . . . . . . . . . . . . . . . . .27
iii

Chapter 3. Verifying the Hardware Operation . . . . . . . . . . . . . . . . . . . . .29
Considerations Before Running This Procedure . . . . . . . . . . . . . . . . . . . . .29
Loading the Online Diagnostics in Service Mode . . . . . . . . . . . . . . . . . . . . .29
Loading the Standalone Diagnostics from CD-ROM . . . . . . . . . . . . . . . . . . . .30
Running System Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Performing Additional System Verification . . . . . . . . . . . . . . . . . . . . . . . .31
Stopping the Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Verifying that the Latest Firmware is Installed . . . . . . . . . . . . . . . . . . . . . .31
Verifying Partition Standby Operation . . . . . . . . . . . . . . . . . . . . . . . . .32
Verifying that the Latest Adapter and Drive Microcode are Installed . . . . . . . . . . . . . .32
Verifying that the Latest HMC Software is Installed . . . . . . . . . . . . . . . . . . . .32
Final Installation Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Completing System Records and Installation Procedure . . . . . . . . . . . . . . . . .32
Configuring the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Chapter 4. Capacity Upgrade on Demand Features . . . . . . . . . . . . . . . . . . .35
Capacity Upgrade on Demand . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Processor CUoD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Memory CUoD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
On/Off Capacity on Demand . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Trial Capacity on Demand . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Capacity Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Software Licenses and Processor CUoD . . . . . . . . . . . . . . . . . . . . . . .37
Activation Process for CUoD Features . . . . . . . . . . . . . . . . . . . . . . . .38
Chapter 5. Installing Options . . . . . . . . . . . . . . . . . . . . . . . . . . .39
PCI Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Removing a PCI Adapter Cassette . . . . . . . . . . . . . . . . . . . . . . . . .40
Replacing an Adapter in a PCI Adapter Cassette . . . . . . . . . . . . . . . . . . . .64
Short Adapter or Blank Filler Installation . . . . . . . . . . . . . . . . . . . . . . .68
Long Adapter Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Appendix A. Communications Statements . . . . . . . . . . . . . . . . . . . . . . 103
Federal Communications Commission (FCC) Statement . . . . . . . . . . . . . . . . . . 103
European Union (EU) Statement . . . . . . . . . . . . . . . . . . . . . . . . . . 103
International Electrotechnical Commission (IEC) Statement . . . . . . . . . . . . . . . . . 103
United Kingdom Telecommunications Safety Requirements . . . . . . . . . . . . . . . . . 103
Avis de conformité aux normes du ministère des Communications du Canada . . . . . . . . . 104
Canadian Department of Communications Compliance Statement . . . . . . . . . . . . . . 104
VCCI Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Electromagnetic Interference (EMI) Statement - Taiwan . . . . . . . . . . . . . . . . . . 104
Radio Protection for Germany . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Appendix B. Environmental Notices . . . . . . . . . . . . . . . . . . . . . . . . 107
Product Recycling and Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Environmental Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Acoustical Noise Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Declared Acoustical Noise Emissions . . . . . . . . . . . . . . . . . . . . . . . . .112
Appendix C. Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
Appendix D. Securing the Rack . . . . . . . . . . . . . . . . . . . . . . . . . .115
Positioning the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Installing the Frame Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
Rack Tie-Down Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
Mounting Internal Rack Components . . . . . . . . . . . . . . . . . . . . . . . .118
iv Eserver pSeries 690 Installation Guide

Determine Your Next Step . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Attach the Rack to a Concrete (Non-Raised) Floor . . . . . . . . . . . . . . . . . . . .119
Attaching the Rack to a Short-Raised or Long-Raised Floor . . . . . . . . . . . . . . . . 122
Installing Frame Ground Straps . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Signal Integrity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Raised-Floor Environments . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Non-Raised Floor Environments . . . . . . . . . . . . . . . . . . . . . . . . . 129
Appendix E. Attaching Multiple pSeries 690s to One Hardware Management Console . . . . . 131
Installing the 8-Port async Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Connect the Serial Cables from the pSeries 690 to the 8-Port Async Adapters . . . . . . . . 132
Installing the 128-Port Async Adapter . . . . . . . . . . . . . . . . . . . . . . . . . 132
128-Port Async Adapter Line Connectors . . . . . . . . . . . . . . . . . . . . . . 133
Setting a RAN Node Number . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Configuring the 128-Port Async Adapter . . . . . . . . . . . . . . . . . . . . . . . 134
Connect the Serial Cables from the pSeries 690 to the 128-Port Async Adapters . . . . . . . . . 136
Verify that Installation is Complete by Using the HMC Interface . . . . . . . . . . . . . . . 137
Appendix F. System Records . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Record the Identification Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Record System - Processor, Memory, and I/O Configuration . . . . . . . . . . . . . . . . 141
Verify that All Hardware is Present . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Appendix G. Power On the System . . . . . . . . . . . . . . . . . . . . . . . . . 147
HMC Power-On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Partition Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Full System Partition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
System Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Power-on Autostart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Appendix H. Subsystem Positioning and Cabling . . . . . . . . . . . . . . . . . . . 151
Operator Panel Cable and Diskette Drive Cable to the Media Subsystem (Rear View) . . . . . . . 151
I/O Subsystem Positions, Fully Populated Primary and Secondary Rack (Rear View without IBF) 152
I/O Subsystem Positions, Fully Populated Primary and Secondary Rack (Rear View with IBFs) . . . 153
Placement of Subsystem 4 in a Two-Rack Configuration (Rear View with IBF) . . . . . . . . . 154
RIO and RIO-2 Cabling Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
I/O Subsystems (1 Through 4 without IBFs) RIO Cabling to I/O Books, Two I/O Planar Loop
Configuration, 2, 3, or 4 MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . 157
I/O Subsystems (5 and 6) RIO Cabling to the Secondary I/O Book, Two I/O Planar Loop
Configuration, 3 or 4 MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . . 158
I/O Subsystems (7 and 8) RIO Cabling to the Third I/O Book, Two I/O Planar Loop Configuration, 4
MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
I/O Subsystems (1 through 3 with IBFs) RIO Cabling to I/O Books, Two I/O Planar Loop
Configuration, 2, 3, or 4 MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . 160
I/O Subsystems (4 through 6 with IBFs) RIO Cabling to I/O Books, Two I/O Planar Loop
Configuration, 3 or 4 MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . . 161
I/O Subsystems (1 Through 4 without IBFs) RIO-2 Cabling to I/O Books, Two I/O Planar Loop
Configuration, 2, 3, or 4 MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . 162
I/O Subsystems (5 and 6) RIO-2 Cabling to the Secondary I/O Book, Two I/O Planar Loop
Configuration, 2 MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
I/O Subsystems (5 and 6) RIO-2 Cabling to the Secondary I/O Book, Two I/O Planar Loop
Configuration, 3 or 4 MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . . 164
I/O Subsystems (7 and 8) RIO-2 Cabling to the Third I/O Book, Two I/O Planar Loop Configuration, 3
or 4 MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
I/O Subsystems (1 Through 4 without IBFs) RIO-2 Cabling to I/O Books, One I/O Planar Loop
Configuration, 3 or 4 MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . . 166
Contents v

I/O Subsystems (5 and 6) RIO-2 Cabling to the Secondary I/O Book, One I/O Planar Loop
Configuration, 3 MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
I/O Subsystems (5 and 6) RIO-2 Cabling to the Secondary I/O Book, One I/O Planar Loop
Configuration, 4 MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
I/O Subsystems (7) RIO-2 Cabling to the Fourth I/O Book, One I/O Planar Loop Configuration, 4
MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
I/O Subsystems (1 through 3 with IBFs) RIO-2 Cabling to I/O Books, One I/O Planar Loop
Configuration, 3 or 4 MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . . 170
I/O Subsystems (1 through 3 with IBFs) RIO-2 Cabling to I/O Books, One I/O Planar Loop
Configuration, 2 MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
I/O Subsystem (4 with IBFs Installed) RIO-2 Cabling to I/O Book 3, One I/O Planar Loop
Configuration, 3 or 4 MCMs Only . . . . . . . . . . . . . . . . . . . . . . . . . 172
Power and SCSI Cables to the Media Subsystem . . . . . . . . . . . . . . . . . . . . 173
Hardware Management Console for pSeries (HMC) to the Primary I/O Book . . . . . . . . . . 174
Appendix I. p690 Cable Installation and Management . . . . . . . . . . . . . . . . . 175
Appendix J. Cabling Information . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Power Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
RIO Cables, RIO-2 Cables, and I/O Power Cables . . . . . . . . . . . . . . . . . . . . 183
Appendix K. Service Processor Setup and Test . . . . . . . . . . . . . . . . . . . . 187
Service Processor Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . 187
Testing the Service Processor Setup . . . . . . . . . . . . . . . . . . . . . . . . . 188
Testing Call-In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Testing Call-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Serial Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Appendix L. Removing and Installing the Rack Top Frame . . . . . . . . . . . . . . . 191
Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Removing the Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Removing the Rack Top Frame for Clearance Through Doorways . . . . . . . . . . . . . . 193
Preparing for Rack Top-Frame Installation for pSeries 690 (Reduced Height Option) RPQ8A1173 198
Installing the Rack Top Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
Replacing Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
vi Eserver pSeries 690 Installation Guide

Safety Notices
Attention: When moving or relocating certain configurations of the system, the Bulk Power Regulators
(BPRs) must be removed from the top of the rack (front and rear) to ensure product stability. Specifically,
removal of the top two BPRs in the front and rear is required in systems that have fewer than 2 I/O
drawers in the rack.
A danger notice indicates the presence of a hazard that has the potential of causing death or serious
personal injury. Danger notices appear on the following pages:
v viii
v 16
A caution notice indicates the presence of a hazard that has the potential of causing moderate or minor
personal injury. Caution notices appear on the following pages:
v viii
v ix
v 16
v 18
v 52
v 64
For a translation of the safety notices contained in this book, see the System Unit Safety Information,
order number SA23-2652.
Rack Safety Instructions
v Do not install this unit in a rack where the internal rack ambient temperatures will exceed 35 degrees C.
v Do not install this unit in a rack where the airflow is compromised. Any side, front or back of the unit
used for air flow through the unit must not be in direct contact with the rack.
v Care should be taken to ensure that a hazardous condition is not created due to uneven mechanical
loading when installing this unit in a rack. If the rack has a stabilizer it must be firmly attached before
installing or removing this unit.
v Consideration should be given to the connection of the equipment to the supply circuit so that
overloading of circuits does not compromise the supply wiring or overcurrent protection. To provide the
correct power connection to the rack, refer to the rating labels located on the equipment in the rack to
determine the total power requirement for the supply circuit.
v An electrical outlet that is not correctly wired could place hazardous voltage on the metal parts of the
system or the devices that attach to the system. It is the responsibility of the customer to ensure that
the outlet is correctly wired and grounded to prevent an electrical shock.
vii

Electrical Safety
Observe the following safety instructions any time you are connecting or disconnecting devices attached to
the system.
Adjust each rear mounting bracket (by loosening the screws) so that the inside distance between the two
ends is equal to the outside dimension of the rack rails.
DANGER
An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of
the system or the devices that attach to the system. It is the responsibility of the customer to
ensure that the outlet is correctly wired and grounded to prevent an electrical shock.
Use one hand, when possible, to connect or disconnect signal cables to prevent a possible
shock from touching two surfaces with different electrical potentials.
During an electrical storm, do not connect cables for display stations, printers, telephones, or
station protectors for communications lines.
D06
CAUTION:
This product is equipped with a four-wire (three-phase and ground) power cable for the user’s
safety. Use this power cable with a properly grounded electrical outlet to avoid electrical shock.
C27
DANGER
To
prevent electrical shock hazard, disconnect all power cables from the electrical outlet before
relocating the system.
D01
CAUTION:
This unit has more than one power supply cord. Follow procedures for removal of power from the
system when directed.
C28
CAUTION:
Energy hazard, remove power before servicing.
C22
CAUTION:
Energy hazard, remove all jewelry before servicing.
C29
viii Eserver pSeries 690 Installation Guide