IBT IBD63 User manual

MicroPCI Card Installation For each OS, users may refer to the
respective procedure below to proceed
with the driver installation.
To insert the MicroPCI daughter cards,
position it at 30°to the PCB and gently
push it into the MicroPCI connector
(Figure 1). The card will not fit when
inserted at an angle of 45°or 15°.
Once inserted, slowly press the card
towards the PCB until it locks on both
sides to the clips of the connector.
Screw the card to the PCB to secure
the installation. To remove the
MicroPCI card, pull the ‘clips’ sideways
as shown in Figure 2.
Driver Installation Procedure for
Windows 95/98
IBD63
MicroPCI VGA Card 1. Find the file "Setup" under the
directory win95/98.
with SiS 6326 VGA Controller 2. Run the program "Setup" by double
clicking on it.
User’s Guide
3. Follow up indication to proceed the
installation procedure.
4. The driver installation will be
completed after system restarts.
Figure 2.
Figure 1.
Driver Installation Procedure for
Windows NT 3.5
1. Select "Main" icon.
2. Select "Control Panel" under "Main".
3. Select "Display" under "Control Panel".
4. Select "Change Display Type" under
"Display Settings".
5. Select "Change .." under "Adapter
Type".
SiS 6326 Driver Installation Guide
6. Select "other .." under "Select Device".
SiS 6326 AGP/PCI Graphics & Video
Accelerator has five sets of drivers for
different operating systems including
Windows 95/98, Windows NT. The location of
these drivers is listed below.
7. Give the path where the driver was
stored under "Install From Disk"
then click "OK". For example:
C:\vga\sis6326\Winnt35
8. Select desired mode such as "SiS
800x600, 256 colors, 85Hz" under
(1). Windows 95 DirectX and utilities:
\VGA\SIS6326\WIN95\SETUP.EXE Select Device" then click "Install".
9. Follow up the coming up indication.
Features
Windows 98 DirectX and utilities:
\VGA\SIS6326\WIN98\SETUP.EXE 10. The driver installation will be
completed after system restarts.
•IBD63 SiS 6326 VGA controller with 4MB memory
•Support to 1024x768/ 800x600/ 640x480 in
8/16/24 bit color format @ 120 Mhz refresh rate (2). Windows NT drivers:
(a). Windows NT 3.5:
\VGA\SIS6326\WINNT35\OEMSETUP.INF
•Support to 1280 x 1024 in 8/16 bit
•Color format @ 85hz refresh rate
•Built-in 64x32x2 bit-mapped hardware cursor (b). Windows NT 4.0:
\VGA\SIS6326\WINNT40\SISV6326.INF
•Display resolution: 320x200 to 1600x1200 pixels
•Integrated 24-bit 203 MHz RAMDAC (c). Windows NT 5.0:
\VGA\SIS6326\WINNT50\SISV6326.INF
•Multi-Monitor capability; Gamma-corrected video
•71mm x 67mm

Driver Installation Procedure for
Windows NT 4.0
1. Select "My Computer" icon.
2. Select "Control Panel" under "My
Computer".
3. Select "Display" under "Control Panel".
4. Select "Settings" under "Display Properties".
5. Select "Display Type" under "Settings".
6. Select "Change.." under "Adapter Type".
7. Select "Have Disk.." under "Change
Display".
8. Select "Browse" under "Install From Disk".
9. Give the path where the driver was stored
under "Locate File" then click "Open". For
example: C:\vga\sis6326\Winnt40
10. Back to "Install From Disk" screen then
click "OK".
11. The message "SiS 6326" will appear under
"Change Display". Click "OK".
12. Confirm "Yes" under "Third-party Drivers".
WinNT 4.0 will perform driver installation and
ask the user to close windows to restart
system.
13. Close "Display Type" window.
14. Close "Display Properties" window.
15. Reboot the system then the driver
installation is completed.