Ice ID8C Programming manual

Operator & Parts Manual
Professional Backpack Vacuum Cleaner
www.icecompanies.com
2730305EU
REV.01(01-2014)
ID8C
INTERNATIONAL CLEANING EQUIPMENT

SAFETY PRECAUTION. . . . . . . . . . . . . . . . . . . . .2
MACHINE OPERATON & STORAGE. . . . . . . . . . . . . 3
MACHINE COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
WEAR&TEAR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
ICE ID8C 1
TABLE OF CONTENTS

SAFETY PRECAUTION
2ICE ID8C
OPERATOR
Carefully read and understand this manual before operating this machine.
This machine must be grounded!
This machine shall be grounded while in use to protect theoperator from electric shock.
Grounding provides a path of least resistance for electric current. This machine is equipped
with a cord having an equipment-grounding conductor and grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and grounded in accordance with all
local codes and ordinances. Do not remove the ground pin under any circumstances.
This machine is for use on a nominal 220-volt circuit
and has a grounding plug that resembles the plug
illustrated in Figure. Make sure that the machine is
connected to an outlet having the same conguration as
the plug. No adapter should be used with this machine.
This machine is intended for commercial use. It is constructed for use in an indoor environment
and is nor intended for any other use. Use only recommended accessories.
1. Do not operate machine:
– Unless trained and authorized. – Unless you have read and
– In ammable or explosive areas. understand the operators manual.
– With a damaged cord or plug – With the use of extension cords.
– If not in proper operating condition. – In outdoor areas and standing water.
2. Before operating machine:
– Make sure all safety devices are in place and operating properly.
3. When using machine:
– Do not run machine over cord. – Do not pull machine by cord or plug.
– Do not pull cord around – Do not unplug by pulling on the cord.
sharp edges or corners. – Do not stretch cord.
– Do not handle plug with wet hands. – Keep cord away from heated surfaces.
– Report machine damage or faulty
operation immediately.
To avoid electrical shock,please replace the power cord immediately if any damage is
being detected. The replacement must be performed only by an authorized person or
by our customer service center.
4. Before leaving or servicing machine:
– Turn off machine. – Unplug cord from outlet.
5. When servicing machine:
– Unplug cord from outlet. – Use manufacturer supplied or
approved replacement parts.

Operation of the Backpack Vacuum
ICE ID8C 3
OPERATOR
Read operators manual thoroughly prior to operating or servicing
this machine.
DRY PICKUP.
3) Connect vacuum hose to inlet on the machine body.
4) Choose appropriate tool, and attach it to the free end of the hose.
5) Plug power cord into grounded outlet.
Be sure the machine is not plugged into an outlet.
1) Remove the cover of machine and conrm that there are a cloth of paper lter and a cloth
bag or paper bag in place.
2) Replace & the latch cover.
STORAGE
1) Unplug machine from power source .
2) Store in upright position in a dry area.
MAINTENANCE
To keep the machine performing well for many years, please follow the following
maintenance procedures.
Always confirm that the machine is unplugged prior to performing any
maintenance or repairs.
1) Unplug machine as soon as you are done using it.
2) Check power cord for any damage. If any damage is detected, replace the cord immediately.
3) Check machine for loose or missing nuts and bolts, and replace as necessary.
4) Check the lter, and clean it after each use
5) Remove the vacuum hose and check it for any holes and clogs
6) Clean the outside of the machine with a mild cleaner
Do not use an extension cord in conjunction with the standard power cord.
6) Place the machine on your back so that the weight of the unit rests on your hips then
fasten the waist belt, adjust shoulder strap until secure and comfortable,you may clip the
switch box to the waist belt.To start the machine ,turn on the red rocker switch.
7) Check the lter bag periodically to see if it is full. For optimal performance, replace the
bag when it is 3/4 full.
9) To stop the machine at any time, simply turn off the rocker switch.

MACHINE COMPONENTS
4 ICE ID8C
OPERATOR
1.Cover 2.Latch
3.Power cord 4.Door,Exhaust lter
5.Exhaust lter 6.On/off switch
7.Tank 8.Back rest assy
3
6
8
1
4,5
2
7

ICE ID8C 5
OPERATOR

6ICE ID8C
DIA
NO
PART
NUMBER DESCRIPTION NO REQ'D
1 2710102 Cover 1
2 2710118 Gasket,Cover 1
32710302 Cloth Bag 10/PK
2710303 Paper Bag(Optional) 10/PK
4 2710301 Cloth Filter 1
5 2710113 Filter Frame 1
6 1123507 Nut, Lock, SST, M5 4
7 1421510 Washer,Plain,∅5.3X∅10X1 10
8 2710124 Filter 1
9 2710121 Mounting Cover,Motor 1
10 2120205 Catch 2
11 1662512 Rivet,∅4.8X12 4
12 2010121 Logo 1
13 2710101 Dust Bag Housing 1
14 1421307 Washer,Plain,∅3X∅7X0.5 12
15 2710119 Housing,Exhaust Filter 2
16 1662310 Rivet,∅3.2X12 12
17 2710120 Exhaust Filter Door 2
18 2710111 Exhaust Filter(HEPA) 2
19 2710110 Gasket,Exhaust Filter 2
20 2710115 Decal 1
21 2710114 Gasket,Motor Support 1
22 2710103 Motor Support 1
23 1221550 Screw,RHM,M5X50,SST 3
24 2710104 Bottom Gasket,Motor 1
25 2710108 Vac Motor,220V 1
26 2710105 Top Gasket,Motor 1
27 2710132 Silencer,Cover 1
28 2710106 Cover,Motor 1
29 1311345 Screw, Ph,ST4.8 X 45 4
30 2710131 Triangular Lower Foam Pad 1
31 2710112 Gasket,Bottom Plate 1
32 2710109 Bottom Plate 1
33 1211512 Screw,RHM,M5X12,SST 3
34 2030414 Warning Decal 1
35 2710309 Serial Decal 1
36 1310016 Screw,Ph,ST2.9X16 2
37 2010126 EMI 1
OPERATOR
PARTS LIST

ICE ID8C 7
DIA
NO
PART
NUMBER DESCRIPTION NO REQ'D
38 2710133 Silencer,Dust Bag Housing 1
39 2710128EU Power Cord 1
40 2320403 Strain Relief 1
41 2710129 Cord 1
42 2710201 Front Cover,Switch 1
43 2710130 Cord 1
44 2710202 Back Cover,Switch 1
45 2110108 Switch 1
46 1123406 Nut, Lock, SST, M4 6
47 1411409 Washer,Plain,∅4X∅9X0.8 14
48 2710127 Cord Wrap 1
49 1321125 Screw, Ph,ST3.5 X 25 3
50 1321110 Screw, Ph,ST3.5 X10 2
51 2710203 Velcro 1
52 2710200 Switch Assy 1
53 1221416 Screw,RHM,M4X16,SST 4
54 2710126 Back Rest Assy 1
55 1221425 Screw,RHM,M4X25,SST 2
56 1321213 Screw, Ph,ST4 X 13 2
OPERATOR
PARTS LIST

8 ICE ID8C
OPERATOR
ACCESSORIES

ICE ID8C 9
OPERATOR
PARTS LIST
DIA
NO
PART
NUMBER DESCRIPTION NO REQ'D
1 2710300 Hose Assy 1
2 2030107 Tube,Sst 2
3 2030220 Combination Tool 1
4 2030104 Dusting Tool 1
5 2030106 Crevice Tool 1
6 2030101 Upholstery Tool 1