iCES ICR-240 User manual

Model: ICR-240
INSTRUCTION MANUAL
www.ices-electronics.com
READ THIS INSTRUCTION MANUAL BEFORE OPERATING THE APPLIANCE.
AND SAVE IT FOR FUTURE REFERENCE.

Top view
Back view

Front view
CONTROLS AND INDICATORS
1. SNOOZE / SLEEP / DIM utto
2. ON / OFF / NAP utto
3. P- utto
4. ALARM  / VOL – utto
5. HOUR / TUNING – utto
6. TIME / PRESET utto
7. P+ utto
8. ALARM  / VOL + utto
9. MIN / TUNING + utto
10. Battery compartment
11. FM antenna
12. AC plug
A. Time and radio frequency display
B. Alarm 2 buzzer
C. Alarm 2 radio indicator
D. FM
E. Alarm 1 buzzer
F. Alarm 1 radio indicator

PREPARATION FOR USE
This clock radio includes a battery backup system that will maintain the time and
alarm settings during a temporary power interruption. Isert two AAA size atteries
correctly by matching the polarity (+/-) markings in the battery compartment (10). If
you experience a power failure while batteries are istalled, the displa will tur off
but the clock will continue to run and maintain your alarm settings. Please replace all
batteries at the same time with only new batteries.
The clock radio has slip proof silicon feet. Place the clock radio only on protected
furniture.
Plug AC plug (12) into 230vac electrical outlet.
Unwind the FM antenna (11) on the back of the clock radio. Extend and reposition
the antenna for best radio reception.
ALARM CLOCK OPERATION
SETTING THE TIME
Note:
You cannot set any function when the clock display is blinking after plug in, press
the TIME/PRESET to stop blink and start setting.
The time can only be set when the radio is turned off. Press the ON / OFF / NAP
button (2) to turn radio on or off.
When the clock display is blinking, you cannot power on radio by the ON / OFF /
NAP utto .
1. Press ad hold dow TIME / PRESET utto  for approiatel  seods
until the display flashes.
2. Press HOUR / TUNING – utto  repeatedly to change the hour setting.
3. Press MIN / TUNING + utto  repeatedly to change the minute setting.
4. Press TIME / PRESET utto  to ofir at the tie ad the displa will stop
flashing.
SETTING THE ALARM TIME
This clock radio has dual alarms that can be set and used independently. The
procedure to set both alarms are the same. Both alarms can either sound the buzzer
or wake up to radio.
Note: The alar tie a ol e set whe the radio is tured off. Press the ON /

OFF / NAP utto  to tur radio on or off.
1. For setting alarm time 1 with buzzer, press ALARM  / VOL – button (4) and
indicator (E) will flash. For settig alar tie  with radio, press ALARM  /
VOL – utto 4) twice and indicator (F) will flash.
2. When the digits are flashing, press HOUR / TUNING – utto  repeatedly to
change the hour setting. Press MIN / TUNING + utto  repeatedly to change
the minute setting.
3. Press ALARM  / VOL – button (4) to confirm.
4. To cancel alarm, press ALARM 1 / VOL – button (4) three times when the
current time is showing. The alarm indicators will be off.
5. When the alarm sounds, press any button to tur off alar or press SNOOZE /
SLEEP / DIM button (1) to enter snooze mode. or will blink during
snooze mode. Alarm will sound again after 5 minutes. Alarm buzzer does not cut
the radio sound. If alarm waken up by radio, volume control for radio is not
available.
6. Follow the sae istrutios for alar  with ALARM  / VOL + utto (8).
Note:
You must make the time and alarm time adjustments while the display is flashing.
The display will stop flashing after approximately 10 seconds if adjustments are
not made.
If two alarms are set together, for example alarm1 set to buzzer alarm and alarm2
set to radio alarm, when buzzer is activated by alarm1 and radio is activated by
alarm2, the previous alarm does not stop automatically and has both buzzer and
radio sound together.
RADIO
General Operations
1. Press the ON/OFF/NAP utto  to tur radio o ad off.
2. For manual tuning, press HOUR / TUNING – utto  or MIN / TUNING
+ utto  for increments of 0.1mHz.
3. For automatic tuning, press and hold down HOUR / TUNING – utto  or
MIN / TUNING + utto  for approximately 3 seconds. Depress the button
and the radio will start to scan for the next available station.
4. Press ALARM  / VOL – utto  or ALARM  / VOL +utto  to adjust