Icom NXDN IC-F5400D SERIES User manual

NXDN™
IC-F5400D/IC-F6400D SERIES
PRODUCT GUIDE
PGX-IC-F5400D/F6400D-V1.0
Version 1.0
December 2016

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
2
This product guide is made to promote our new products, the IC-F5400D/IC-F6400D transceivers. The new
product's technology components are described in this document, and you will understand the target users,
built-in functions, and sales points of these transceivers. This product guide's target users are dealer sales
staff members who are going to sell these transceivers for the first time.
Icom hopes this product guide will help you to promote sales of the IC-F5400D/IC-F6400D series
transceivers.
Trademarks
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the
United States, the United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other
countries.
COMMANDMIC is a trademark of Icom Incorporated.
NXDN is a trademark of Icom Incorporated and JVC Kenwood Corporation.
The Bluetooth®word mark and logos are registered trademark owned by Bluetooth SIG, Inc. and any use of
such marks by Icom Inc. is under license.
LTR is a trademark of the E.F. Johnson Technologies, INC.
3M, Peltor, and WS are trademarks of 3M Company.
All other trademarks are the properties of their respective holders.
© 2016 Icom Inc.
PREFACE

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
3
SECTION 1 PRODUCT OUTLINES..........................................................................................................4
1-1 ABOUT THE PRODUCT OUTLINES, SALES POINTS, AND TARGET USERS........4
1-2 IC-F5400D/IC-F6400D’S SPECIFICATIONS...............................................................9
SECTION 2 PRODUCT RANGE.............................................................................................................11
SECTION 3 COMPARISON WITH EXISTING MODELS .......................................................................12
3-1 FUNCTION COMPARISON BETWEEN THE IC-F5400D/IC-F6400D AND
EXISTING MODELS ..................................................................................................12
3-2 FUNCTION COMPARISON BETWEEN THE IC-F5400D/IC-F6400D AND
IC-F5060D/IC-F6060D ...............................................................................................13
3-3 SPECIFICATION COMPARISON BETWEEN IC-F5400D AND IC-F5060D.............14
3-4 SPECIFICATION COMPARISON BETWEEN IC-F6400D AND IC-F6060D.............15
SECTION 4 NEW FUNCTION INTRODUCTION....................................................................................16
SECTION 5 ACCESSORIES...................................................................................................................22
APPENDIX REQUIRED EQUIPMENT FOR SYSTEM CONSTRUCTION.............................................25
TABLE OF CONTENTS

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
4
About the IC-F5400D/IC-F6400D series transceivers
The IC-F5400D/IC-F6400D series transceivers have a drastically changed appearance from traditional Icom
land mobile transceivers, and operability that adapts a diversified operating style. In addition, the
transceivers are compatible with NXDN™ Single-site trunking and Multi-site trunking systems by utilizing an
activation license.
Sales point
• Model line-up suitable for various operating purposes.
IC-F5400D/IC-F6400D IC-F5400DS/IC-F6400DS
Equipped with a color LCD Equipped with a 7 segment display
• Equipped with larger-sized keys
Enlarged function keys are built-in to the IC-F5400D/IC-F6400D compared to the IC-F5060D/IC-F6060D
series transceivers. In addition, the built-in [UP]/[DOWN]/[LEFT]/[RIGHT] keys improves operability, and
menu selection.
• Equipped with a color LCD
The IC-F5400D/IC-F6400D series transceivers have a color LCD. The size of the LCD is larger than the
IC-F5060D/IC-F6060D series transceivers, so the visibility is also drastically improved.
Front view and size comparison
• Improved waterproof/dustproof
The waterproof/dustproof grade is improved from IP54 (controller only) to IP55 (both controller and main
unit), compared to the IC-F5060D/IC-F6060D series transceivers.
1-1 ABOUT THE PRODUCT OUTLINES, SALES POINTS, AND TARGET USERS
SECTION 1 PRODUCT OUTLINES
IC-F5400D/IC-F6400D
55
174
IC-F5060D/IC-F6060D
160
45

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
5
• Improved optional unit attachment
The controller can be detached without using a screw driver. Therefore, the optional unit can easily be
attached.
Controller
To detach the controller, pull up on the
latches to unlock the controller.
Bottom view of the main unit.

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
6
• A 2.37 inch large size color LCD
You can easily see a lot of information on the 320 × 150 dot color LCD display.
You can set the menu items to be visible or invisible in the programming software.
• Local language support
Menu item names and messages can be displayed in languages other than English.
NOTE: Names and messages in languages can be preprogrammed using the programming software.
If the main unit firmware revision is 1.6 or later, English, German, French, Spanish, Russian, and Chinese
are supported.
• A user interface improves the operability compared with previous Icom land mobile transceivers.
You can reach desired operations and/or settings by only selecting the icon, or from a list on the menu
screen.
USB mode selecting example
TX noise canceling setting example
Target ID selecting example
English French German
Menu screen Message screen Execution confirmation
screen
Night mode screen

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
7
• Various operation styles (Available only for IC-F5400D/IC-F6400D)
IC-F5400D/IC-F6400D transceiver can be operated in the following operation styles. Each operation style
requires main unit firmware revision 1.6 or later.
Detached controller style
You can install the controller close to the operator. Therefore, you can efficiently use the limited space in
a vehicle or the top of a desk.
Dual head controller style
You can attach two controllers, one near the driver seat and one near the operation panel of a fire engine.
Therefore, you can operate the transceiver from either location.
COMMANDMIC™ and detached controller style
You can operate the transceiver from the driver seat in a mobile crane using the controller, or at the crane
controls using the COMMANDMIC™.

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
8
Target users
B & I markets
(Transport, and so on)
Headquarters of security services
Public works (Electric power
industry, Water services,
and so on)
• Users who require the AES/DES encryption function.
• Users who require languages other than English.
Construction sites
Public safety
Taxi companies
Transportation businesses

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
9
Model name IC-F5400D IC-F6400D
Version #01, #11 #01, #11, #21, #31
Destination USA-01, USA-11 USA-01, USA-11, USA-21,
USA-31
GENERAL
Frequency coverage 136 ~ 174 MHz 380 ~ 470 MHz
450 ~ 512 MHz
Number of conventional channels 1,024 ch/128 zones [IC-F5400D, IC-F6400D]
4,000 ch/128 zones [The license is activated.]
99 ch [IC-F5400DS/IC-F6400DS]
Type of emission A: 11K0F3E (15.0 kHz)
D: 4K00F1E, D (6.25 kHz); 8K30F1E, D (12.5 kHz)
Intermediate frequency 1st: 49.95 MHz, 2nd: 450 kHz
Power supply voltage 13.6 V DC nominal Negative ground
Current drain
(approximately)
TX High 9.0 A typical (at 50 W) 8.8 A typical (at 45 W)
Low (at 25 W) 5.0 A typical
RX Maximum audio 900 mA typical
(Internal speaker)
800 mA typical
(Internal speaker)
Stand by 370 mA typical 270 mA typical
Antenna impedance 50 nominal
Microphone impedance 600 
Audio impedance 4 
Operating temperature range –30 °C ~ +60 °C; –22 °F ~ +140 °F
Dimensions (W H D)
(Projections not included) 174

55

150 mm;
6.8 2.2 5.9 inches
Weight (approximately) 1.5 kg; 3.3 lb
TRANSMITTER
Output power (at 13.6 V DC) 50 W 45 W
Modulation Frequency modulation, FSK modulation
Maximum frequency deviation A: ±2.5 kHz
Frequency error ±1.0 ppm
Spurious emissions 90 dB typical 80 dB typical
Adjacent channel power A: 66 dB typical
D: 66 dB typical (6.25 kHz),
67 dB typical (12.5 kHz)
Audio harmonic distortion 0.5% typical @ AF 1 kHz 40% deviation
FSK error 1% typical (D: 6.25 kHz/12.5 kHz)
FM hum and noise (without CCITT filter) 54 dB typical
Limitation characteristics of the modulator 70% ~ 100% of max. deviation
A: Analog
D: Digital
1-2 IC-F5400D/IC-F6400D’S SPECIFICATIONS

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
10
Model name IC-F5400D IC-F6400D
RECEIVER
Sensitivity
• 0.22 V typical
@ 12 dB SINAD
• 6.0 dBV (EMF) typical
@ 1% BER (D: 6.25 kHz)
• 5.0 dBV (EMF) typical
@ 1% BER (D: 12.5 kHz)
• 0.25 V typical
@ 12 dB SINAD
• 6.0 dBV (EMF) typical
@ 1% BER (D: 6.25 kHz)
• 5.0 dBV (EMF) typical
@ 1% BER (D: 12.5 kHz)
Audio power output 4.0 W typical @ 5% distortion into 4 
Adjacent channel selectivity A: 72 dB typical
D: 65 dB typical (6.25 kHz),
68 dB typical (12.5 kHz)
Spurious response rejection 85 dB typical
Intermodulation A: 78 dB typical
D: 70 dB typical
(6.25 kHz/12.5 kHz)
A: 75 dB typical
D: 70 dB typical
(6.25 kHz/12.5 kHz)
Hum and noise (without CCITT filter) 48 dB typical
Squelch sensitivity (Threshold) 0.22 V typical 0.25 V typical
A: Analog
D: Digital
Specifications: Measurements made in accordance with TIA-603.

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
11
The IC-F5400D/IC-F6400D series transceivers are excellent in operability, built-in functions, and scalability.
The transceivers are positioned as high grade land mobile transceivers, as shown in the following positioning
map. You can see that the IC-F5400D/IC-F6400D series transceivers are higher grade than the IC-
F5060D/IC-F6060D series transceivers on the map.
SECTION 2 PRODUCT RANGE
Released
(High)
(New)
Product grade
IC-F5060 series
(2006.12－)
IC-F5400D series
(2016)
IC-F5120D series
(2010.11－)

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
12
Models
Functions
IC-F5400D
IC-F6400D
Series
IC-F5060D
IC-F6060D
Series
IC-F5120D
IC-F6120D
Series
NXDN™Type-D single-site trunking
YES
(Optional
ISL-UGMTR is
required.)
YES YES
NXDN™Type-D multi-site trunking
YES
(Optional
ISL-UGMTR is
required.)
YES None
PTT ID YES YES YES
Individual ID List YES
(Max. 1,000ID)
YES
(Max. 500ID)
YES
(Max. 500ID)
Talkgroup ID List YES
(Max. 1,000ID)
YES
(Max. 500ID)
YES
(Max. 500ID)
Log for Individual Call YES YES YES
RX Group YES None None
Block Decode YES YES YES
RAN code YES YES YES
Status YES YES YES
Short Data Message (SDM) YES YES YES
Call Alert YES YES YES
Radio Check YES YES RX only
Stun/Revive/Kill YES YES RX only
Remote Monitor YES YES RX only
Digital voice scrambler YES YES YES
Multiple languages YES None None
DES
(4 or less keys) YES None None
(5 or more keys) YES
(Optional UT-134 is
required.)
None None
AES
YES
(Optional UT-134
and ISL-AKAES are
required.)
None None
GPS unit Built-in
(Optional UX-241 is
required.)
Optional
(User supplied)
Optional
(User supplied)
GPS position data TX/RX TX/RX TX/RX TX only
Emergency function
Emergency key YES YES YES
Lone Worker YES YES YES
SECTION 3 COMPARISON WITH EXISTING MODELS
3-1 FUNCTION COMPARISON BETWEEN THE IC-F5400D/IC-F6400D AND
EXISTING MODELS

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
13
FUNCTION IC-F5400D/IC-F6400D
SERIES IC-F5060D/IC-F6060D SERIES
Operation type
Single-site conventional YES YES
Multi-site conventional YES YES
Single-site trunking Optional YES
Multi-site trunking Optional YES
Analog mode YES YES
6.25 kHz Digital mode YES YES
12.5 kHz Digital mode YES None
Analog/Digital mix mode YES YES
25 kHz bandwidth operation YES (Optional for [USA]) None
Voice functions
Voice announcement YES None
Voice Recording/Playback function YES
(A microSD or microSDHC
card is required.)
None
Active Noise Cancelling (ANC) YES None
TX Audio Equalizer YES None
RX Audio Equalizer YES None
Digital functions
Lone worker function YES YES
Radio Check YES YES
Stun/Kill/Revive YES YES
Remote Monitor YES YES
Call Alert YES YES
Emergency YES YES
Short Data Message (SDM) YES YES
Status Message YES YES
Digital voice scrambler YES YES
56 bit DES encryption YES
(4 keys: Default)
(64 keys: Optional)
None
256 bit AES encryption Optional None
Transparent data mode YES None
OAA (Over-the-Air Alias) YES None
OTAP (Over-The-Air Programming) Optional None
OTAR (Over-The-Air-Re-keying) Optional None
Analog functions
CTCSS YES YES
DTCS YES YES
2 Tone YES YES
5 Tone YES YES
DTMF YES YES
MDC1200 YES YES
LTR™ trunking YES YES
Hardwares
GPS receiver YES
(Optional UX-241 is required.)
None
(User supplied.)
Bluetooth
®
YES None
microSD/SDHC memory card slot YES None
USB connector YES None
Dual head controller Optional None
COMMANDMIC™ Optional None
3-2 FUNCTION COMPARISON BETWEEN THE IC-F5400D/IC-F6400D AND
IC-F5060D/IC-F6060D

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
14
SPECIFICATIONS IC-F5400D SERIES IC-F5060D SERIES
GENERAL
Channel capacity 1,024 channels/128 Zones
(Maximum: 4,000 channels) 512 channels/128 Zones
Type of emission A: 11K0F3E
D: 4K00F1E, D (6.25 kHz)
8K30F1E, D (12.5 kHz)
A: 11K0F3E
D: 4K00F1E, D (6.25 kHz)
Intermediate frequency 1st: 49.95 MHz
2nd: 450 kHz
1st: 46.35 MHz
2nd: 450 kHz
Current drain
(approximately)
TX High (50 W) 9.0 A typical 14.0 A
Low2 (25 W) 5.0 A typical 7.0 A
RX Maximum
audio 900 mA typical
(Internal speaker)
1200 mA
(Internal speaker)
Stand by 370 mA typical 300 mA
Dimensions (W H D)
(Projections not included) 174

55

150 mm
6.8 2.2 5.9 inches
160 45 150 mm
6.3 1.8 5.9 inches
IP rating IP55 IP54 (Front panel only)
Weight (approximately) 1.5 kg; 3.3 lb 1.3 kg; 2.9 lb
TRANSMITTER
FM hum and noise (without CCITT
filter) 54 dB typical 40 dB typical
Spurious emissions 90 dB typical 75 dB typical
Adjacent channel power A: 66 dB typical
D: 66 dB typical (6.25 kHz)
67 dB typical (12.5 kHz)
A: 60 dB minimum (6.25 kHz)
Audio harmonic distortion 0.5% typical 3% typical
FSK error 1% typical (D) 5% maximum (D)
RECEIVER
Sensitivity
A: 0.22 V typical
@ 12 dB SINAD
D: 6.0 dBV (EMF) typical
@ 1% BER (6.25 kHz)
5.0 dBV (EMF) typical
@ 1% BER (12.5 kHz)
A: 0.25 V typical
@ 12 dB SINAD
Adjacent channel selectivity A: 72 dB typical
D: 65 dB typical (6.25 kHz)
68 dB typical (12.5 kHz)
A: 75 dB typical (6.25 kHz)
Spurious response rejection 85 dB typical 90 dB typical
Intermodulation A: 78 dB typical
D: 70 dBV (EMF) typical
(6.25 kHz/12.5 kHz)
A: 77 dB typical (6.25 kHz)
Hum and noise (without CCITT filter) 48 dB typical 45 dB typical
Squelch sensitivity (Threshold) 0.22 V typical 0.25 V typical
A: Analog
D: Digital
3-3 SPECIFICATION COMPARISON BETWEEN IC-F5400D AND IC-F5060D

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
15
SPECIFICATIONS IC-F6400D SERIES IC-F6060D SERIES
GENERAL
Channel capacity 1,024 channels/128 Zones
(Maximum: 4,000 channels) 512 channels/128 Zones
Type of emission A: 11K0F3E
D: 4K00F1E, D (6.25 kHz)
8K30F1E, D (12.5 kHz)
A: 11K0F3E
D: 4K00F1E, D (6.25 kHz)
Intermediate frequency 1st: 49.95 MHz
2nd: 450 kHz
1st: 46.35 MHz
2nd: 450 kHz
Current drain
(approximately)
TX High (50 W) 8.8 A typical 14.0 A
Low2 (25 W) 5.0 A typical 7.0 A
RX Maximum
audio 800 mA typical
(Internal speaker)
1200 mA
(Internal speaker)
Stand by 270 mA typical 300 mA
Dimensions (W H D)
(Projections not included) 174

55

150 mm
6.8 2.2 5.9 inches
160 45 150 mm
6.3 1.8 5.9 inches
IP rating IP55 IP54 (Front panel only)
Weight (approximately) 1.5 kg; 3.3 lb 1.3 kg; 2.9 lb
TRANSMITTER
FM hum and noise (without CCITT
filter) 54 dB typical 40 dB typical
Spurious emissions 80 dB typical 75 dB typical
Adjacent channel power A: 66 dB typical
D: 66 dB typical (6.25 kHz)
67 dB typical (12.5 kHz)
A: 60 dB minimum (6.25 kHz)
Audio harmonic distortion 0.5% typical 3% typical
FSK error 1% typical (D) 5% maximum (D)
RECEIVER
Sensitivity
A: 0.25 V typical
@ 12 dB SINAD
D: 6.0 dBV (EMF) typical
@ 1% BER (6.25 kHz)
5.0 dBV (EMF) typical
@ 1% BER (12.5 kHz)
A: 0.25 V typical
@ 12 dB SINAD
Adjacent channel selectivity A: 72 dB typical
D: 65 dB typical (6.25 kHz)
68 dB typical (12.5 kHz)
A: 75 dB typical (6.25 kHz)
Spurious response rejection 85 dB typical 90 dB typical
Intermodulation A: 75 dB typical
D: 70 dBV (EMF) typical
(6.25 kHz/12.5 kHz)
A: 77 dB typical (6.25 kHz)
Hum and noise (without CCITT filter) 48 dB typical 45 dB typical
A: Analog
D: Digital
3-4 SPECIFICATION COMPARISON BETWEEN IC-F6400D AND IC-F6060D

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
16
The new functions are included in the main firmware revision 1.6 or later.
• Bluetooth®function
A third party Bluetooth®headset (3M™ PELTOR™ WS™ Headset XP, 3M™ PELTOR™ WS™ ProTac XP,
or 3M™ PELTOR™ WS™ Alert XP)* can be used for wireless headset operation. This allows you a flexible
installation style, and will not restrict operator’s activity caused by the connection cable and its length.
The adopted Bluetooth®is compatible with Class 1 and Bluetooth®version 2.1+EDR, and the details of the
compatible profile are as shown in the table below.
*Only PTT switch action is checked. Icom does not guarantee all functions and performance of the
Bluetooth®headset.
Table 4-1. Compatible profile
Profile Application
HFP (Hands-Free Profile) Used when transmitting/receiving a signal, hands
free.
HSP (Headset Profile) Used with a connected headset.
SPP (Serial Port Profile)
Used when connecting two devices using a virtual
serial port. (Used for programming the transceiver
without a programming cable.)
• Active Noise Cancelling function
The Active Noise Cancelling function, which is already used in Icom marine transceivers, can suppress
background noise. By using this function, you can transmit clear voice even in a noisy environment, such as
in a downtown area, or near a high traffic main road. The function can also be activated while receiving a call.
The suppression level of the Active Noise Cancelling function can be set to one of three levels. Up to 30%*
of noise for transmit audio, and up to 90%* of noise for receive audio will be suppressed.
*Theoretical value.
Figure 4-1. Active Noise Cancelling function’s image
SECTION 4 NEW FUNCTION INTRODUCTION
Active Noise Cancelling
Background noise Voice Background noise is suppressed. Voice

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
17
• Voice recorder function
The voice recorder function can record both transmitting and receiving voice audio onto a microSD* or
microSDHC* card (hereinafter called microSD* card). The recorded voice audio can be played back on the
transceiver or a PC.
*User supplied.
The voice recorder function specifications are as follows.
Digitization method: PCM
Sampling frequency: 8 kHz
Bit rate: 16 bit
File format: WAVE format
The recordable time for each microSD card’s capacity is shown in the following table.
Table 4-2. The recordable time (theoretical value)
Card type Card capacity Recordable time
microSD
512 MB 8 hours
1 GB 15.6 hours
2 GB 31.3 hours
microSDHC
4 GB 62.5 hours
8 GB 125 hours
16 GB 250 hours
32 GB 500 hours
• The DES/AES encryption function
A 56 bit DES encryption function can be used. (The IC-F5400D/IC-F6400D series transceiver has 4 DES
keys by default.)
When the optional UT-134 is installed in the transceiver, the function will be upgraded as follows.
If you want to use the UT-134, update the main unit firmware to revision 1.6 or later, and program the DES
key with the optional CS-KLD2.
The number of DES encryption keys has been increased from 4 to 64.
When the optional UT-134 is installed, the originally used 4 DES keys must be reentered.
If you purchase the Activation key, 256 bit AES encryption can also be used. In this case, a total of 64
encryption keys that include both AES and DES can be used.
The required items to use the DES/AES encryption function are described in Table 4-3.
Table 4-3. The required items to use the DES/AES encryption function
To use 4 or less DES
encryption keys.
To use 5 or more DES
encryption keys.
To use AES
encryption keys
Transceiver’s default
function. YES NO NO
Activation key is required. NO NO YES
(ISL-AKAES)
The optional UT-134 is
required. NO YES YES
Required software to enter
the key. CS-F3400D CS-KLD2 CS-KLD2

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
18
• Transparent data mode
The IC-F5400D/IC-F6400D series transceivers have the Transparent data mode. The Transparent data
mode enables data transmission at 3600 bps. This function enables you to transmit simple measuring data,
such as air temperature, or still images for remote monitoring.
Figure 4-2. Transparent data mode application example
• OAA (Over-the Air Alias) function
Even if the IC-F5400D/IC-F6400D series transceivers receive a signal that is not programmed into the Call
List, this function can automatically display and program the caller’s name with an ID. When you add new
transceivers in your system, the transceiver can display the name corresponding to an Individual
ID/Talkgroup ID on the display without reentering, by using this function. If the caller’s name set in the
transceiver is changed, the receiving transceiver automatically changes the ID name.
Figure 4-3. OAA example
• 12.5 kHz Digital mode operation
You can select the channel spacing between 6.25 kHz and 12.5 kHz in the digital mode using the
programming software.
• Field programming by Over-The-Air programming (OTAP) can be done (a license is required.)
Even if you have to change the transceiver settings, you can remotely do it without taking it to your dealer, by
using the OTAP function. Installing the software* for the OTAP function onto the PC is required.
*Available in the near future.
Sending a picture
Office PC
(Viewing the received picture)
Conv ID: 3
Name: TR3
Conv ID: 4
Name: TR4
The ID name “TR3” is automatically programmed as ID 3’s name.
OAA

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
19
• Expanding functions by activation licenses
The IC-F5400D/IC-F6400D series transceivers can expand their functions using an activation license. You
can upgrade the transceiver using the programming software. The license is linked to the transceiver's serial
number. Therefore, a unique license is required for each transceiver. The following licenses are sold, or will
be sold in the near future.
Table 4-4. License list
License name Expanding function
ISL-UGMTR For NXDN™ Type-D trunking operation.
ISL-CHEX To increase channel number from 1,024 to 4,000.
ISL-AK25K For 25 kHz (Wide) operation (only [USA]).
ISL-AKAES For AES encryption operation.
ISL-AKSTM For access to the dealer set mode.
• Programming using a microSD card
You can save the transceiver’s setting on a microSD card, or load the saved setting to the transceiver.
Therefore, you can save or change the setting in the field without using the programming software. So, when
multiple operators share one transceiver, you can easily change the transceiver’s setting for each operator
with this function. A microSD card is required.
• GPS position indication
The IC-F5400D/IC-F6400D series transceivers have a built-in GPS receiver, and current position information
can be displayed on the transceiver’s LCD display. You can know your own position by displaying the
information. You can transmit your position information. The transmitted position is used to display the
transceiver’s position on a map by using a third party AVL system.
In addition, other transceiver’s relative position can be displayed on the display. For example, your
transceiver receives position information from the transceiver whose Individual ID name is ID 2, information
is displayed as shown in figure 4-6.
Figure 4-4. Position information display example
Figure 4-5. ID 2’s position information display example
Latitude
Longitude
Altitude
ID 2’s latitude
ID 2’s longitude
The distance from your
own station to ID 2.
Direction from own
station to ID 2.

NXDN™ IC-F5400D/IC-F6400D SERIES PRODUCT GUIDE
20
• TX/RX audio equalizer function
This function can improve or correct the TX/RX audio readability by increasing or decreasing particular audio
frequency components. This function requires main unit firmware revision 1.6 or later.
• Hot DTMF function
The IC-F5400D/IC-F6400D series transceiver has the Hot DTMF function that can transmit DTMF signals
without holding down [PTT] when you use a DTMF microphone. This function requires main unit firmware
revision 1.6 or later.
• Dealer set mode function
The dealer set mode can change the frequency without the programming software. If you want to use the
dealer set mode, an optional license (ISL-AKSTM) is required. The following operation is required to enter
the dealer set mode.
Turn OFF the transceiver’s power.
While holding down [P1] and [UP], turn ON the power.
This function requires main unit firmware revision 1.6 or later.
• The controller and main unit can be separated (Only IC-F5400D/IC-F6400D)
If the main unit firmware revision is 1.6 or later, 3 styles of controller separate operation can be used. The
required equipment for each style is listed in Tables 4-5, 4-6, and 4-7.
Detached controller style
Table 4-5. Required equipment for the detached controller style
Category Product name Quantity
SEPARATION KIT RMK-5 One
SEPARATION CABLE
for RMK-5 or RMK-7
OPC-2364 (1.9 m/ 6.2 ft)
Either one
OPC-2365 (3 m/ 9.8 ft)
OPC-2366 (5 m/ 16.4 ft)
OPC-2367 (8 m/ 26.2 ft)
MICROPHONE
HM-220 (HEAVY-DUTY MICROPHONE; IP54)
Either one
HM-220T (HEAVY-DUTY MICROPHONE WITH DTMF
KEYPAD; IP54)
HM-221 (MICROPHONE; IP55)
HM-221T (DTMF MICROPHONE; IP55)
SEPARATION CABLE
for RMK-5 or RMK-7
MICROPHONE
SEPARATION KIT