ICON 58990 Assembly instructions
Visit our website at: http://www.harborfreight.com
TM
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 21i
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2021 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Page 2 For technical questions, please call 1-888-866-5797. Item
IMPORTANT SAFETY INFORMATION
To prevent serious injury, FIRE, and EXPLOSION:
1. Contains Li-Ion battery. Battery must be
recycled or disposed of properly. Do not open,
crush, heat above 140° F or incinerate.
2. Only use included charging adaptors. Other
adaptors may damage tool or cause fire.
3. Do not submerge Light. Keep dry.
4. Do not operate in explosive atmospheres, such as in
the presence of flammable liquids, gases, or dust.
5. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
6. Not a toy. Keep out of reach of children.
SAVE THESE INSTRUCTIONS.
Specifications
Bar Extension 32" to 77"
Battery Li-Ion 3.7V 5200mAh
Input Rating 5VDC, 2A
Single Light Output
2100 Lumens (High Mode)
1000 Lumens (Med. Mode)
280 Lumens (Low Mode)
2-Light Output
(second light sold separately)
4200 Lumens (High Mode)
2000 Lumens (Med. Mode)
560 Lumens (Low Mode)
Light Run Time, approximate
High Mode: 2.5 Hours
Med. Mode: 5.5 Hours
Low Mode: 12 Hours
Charge Time* 3 Hours
Weather Rating IP65
*Note: Charge time will vary depending on amp rating of the USB port to which the cord is attached.
Components
Power Button
Charging
Jack Cover
Light Holder
Slider Adjustment
Block
Magnetic Base
Support
Battery Level
LEDs
Page 3For technical questions, please call 1-888-866-5797.Item
Operation
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
1. Press button on Slider Adjustment Block and
extend bar to approximate desired length.
2. Release button.
3. Place Supports over hood. Use Slider
Adjustment Block to take up any slack.
4. Mount the Light's Magnetic Base to one of the
Light Holders. Alternatively, the Light's Magnetic
Base can be placed on any ferrous surface.
5. Press button on Light Holder and slide Light
into position along the bar. Release button.
6. Press the Power Button on back of
Light for low, again for medium, again
for high and again to turn off.
7. When the Light is on, the three LED's indicate
battery level. Charge battery when all indicator
LEDs are off and Light will not turn on.
8. When finished using the Underhood Light System,
turn off Light and store indoors away from children.
Charging Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
1. Turn off Light and remove Charging Jack
Cover. Plug the USB Charging Cable (not
included) into the Charging Jack.
2. Plug the other end of the USB Charging
Cable into a powered USB port.
3. LEDs will blink green during charging. When
charging is done, LEDs will stay green.
4. Unplug the USB Charging Cable and
replace Cover on Charging Jack.
NOTICE: Do not leave the Battery in a discharged
state. Charge the Battery every 3 months if the
Light is not in use. This will keep the Battery
from wearing down and add to its life.
Battery Removal
1. Contains Li-Ion battery. Battery must be
recycled or disposed of properly.
2. Turn Light off. Remove six screws and cover.
3. Remove four screws from internal
cover. Remove internal cover.
4. Cut battery wires and remove battery.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Replacement parts are not available for this item. Refer to UPC 193175453907.
. Do not open the housing, there are no user-serviceable parts inside.
TM
26541 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability
standards, and warrants to the original purchaser that this product is free from defects in materials
and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to
damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside
our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion
may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Other ICON Automobile Accessories manuals
