iCONNECT PRL-60-240 User manual

1
INSTALLATION INSTRUCTIONS
Thank you for buying iConnect products.
The PRL is the latest technology in projector lifts.
Please read this manual carefully before assembling.
PROJECTOR LIFT
PRL-60-240

2
CONTENTS
MAIN
CONTENTS
SAFETY
OVERVIEW
LIFT PREPARATION
LIFT INSTALLATION
FINISHING THE CEILING LIFT
ADJUSTMENTS
FINISH
DIMENSION
TECHNICAL SPECIFICATION
iCONNECT
1.
2.
3.
4.
5-6.
7-10.
11-12 / 16-17.
13-15.
18.
19.
20.

Projector lift PRL-60-240 must be installed by specialized personnel only.
Before installing the projector lift, please read the following instructions carefully
1. The projector lift must be used indoors only.
2. It is forbidden to stay under the lift.
3. never connect more than one lift motor to the same switch.
4. In case of maintenance, unplug the power supply.
5. Incorrect use, including exceeding the maximum lifting weight, would be dangerous and invalidate the
warranty.
6. The manufacture do not take responsibility for any damage to property or personal injury, if the lift is used
out side of recommended specifications.
7. Incorrect servicing could lead to risk of electric shock.
8. For any repairing, please contact directly the dealer you purchased the unit from.
9. Check at least once a year that the screws of the steel cables are well tightened
iCONNECT
3
SAFETY

iCONNECT
Projector
Motor
Projector Mount
Adjustable Mount Plate
Linkage
Pulley
Lift Frame
Limit Switch
Lift Frame
OVERVIEW
4

5
Remove Adjustable Mount Plate
Remove the 8 screws
iCONNECTLIFT PREPARATION

LIFT PREPARATION
Open a hole in the ceiling
600mm
600mm
6
iCONNECT

7
Mark and drill 4 holes in the ceiling with a diameter of 10 mm
The direction of the screen
iCONNECTLIFT INSTALLATION

8
Tighten bolts through the holes designated lift and strong
Make sure you locked well
iCONNECTLIFT INSTALLATION

9
Use a power cable that came with the package. plug the male and female side motor
Connect the other end of the cable to a power source 110 V
Press the switch and lower the lift down
iCONNECTLIFT INSTALLATION

10
Unplug the projector arm by opening the screw at the top
iCONNECTLIFT INSTALLATION

11
Create a wooden surface thickness of 12 mm and set it with 9 screws
450 mm
450 mm
iCONNECTFINISHING THE CEILING LIFT

12
Reconnect Adjustable Mount Plate
iCONNECTFINISHING THE CEILING LIFT

13
Stop and drop tuning of the lift is preformed by allen plastic screwdriver supplied only
iCONNECTADJUSTMENTS
The motor two allen screws, one controls the rotation decrease and second rounds of closing

14
Adjust the height of the closure with a ceiling
iCONNECTADJUSTMENTS

15
Adjust the desired opening height
iCONNECTADJUSTMENTS

16
Create a wooden surface close to the desired size, please
leave a margin of 2 mm on each side main square
454mm
454mm
iCONNECTFINISHING THE CEILING LIFT

17
Set the wood surface with a ceiling and make sure it is
installed in the desired location
iCONNECTFINISHING THE CEILING LIFT

18
install the projector on the arm and return it to the designated place in
the lift, set the projector to the desired location
Enjoy the product (-;
iCONNECTFINISH

19
iCONNECTDIMENSION

Product Code
PRL-60
PRL-120
PRL-180
PRL-240
Control Options
Contact closure / RF
Contact closure / RF
Contact closure / RF
Contact closure / RF
Finish / Custom
White RAL 9016
White RAL 9016
White RAL 9016
White RAL 9016
Open Travel
600 mm
1200 mm
1800 mm
2400 mm
Max Weight
12kg
12kg
12kg
12kg
Dimensions
H+W+D
550 x 520 x
215 mm
550 x 520 x
255 mm
550 x 520 x
315 mm
550 x 520 x
355 mm
Weight
10kg
11kg
12kg
13kg
Power supply
Input 100-240V
Input 100-240V
Input 100-240V
Input 100-240V
20
TECHNICAL SPECIFICATION iCONNECT