ICP DAS USA DL-100T485 User manual

DL-100T485 Quick Start V.104
DL-100T485 Quick Start
Warranty
All products manufactured by ICP DAS are under
warranty regarding defective materials for a period of
one year from the date of delivery to the original
purchaser.
Warning
ICP DAS assumes no liability for any damage resulting
from the use of this product. ICP DAS reserves the right
to change this manual at any time without notification.
The information furnished by ICP DAS is believed to be
accurate and reliable. However, no responsibility is
assumed by ICP DAS for its use, nor for any
infringements of patents or other rights of third parties
resulting from its use.
Copyright
Copyright© 2014 ICP DAS. All rights reserved.
Trademarks
Names are used for identification purposes only and may
be registered trademarks of their respective companies.
Date: 2014/6/18

DL-100T485 Quick Start V.104
Table of Contents
Before you use the Utility Software...............................................................................3
DL-100T485 Utility Illustration ....................................................................................4
Connecting to the DL-100T485.....................................................................................5
Retrieving Records.........................................................................................................6
Configuration.................................................................................................................7

DL-100T485 Quick Start V.104
Before you use the Utility Software
1. Before you use this Utility, please make sure you have installed the
Microsoft .NET Framework 4. If you haven’t installed .NET Framework yet,
please refer to section 2 for more information, or refer tonsection 3 for
more information about the installation of this Utility.
2. To download .NET Framework, refer to :
http://www.microsoft.com/downloads/en/details.aspx?FamilyID=9cfb2d51
-5ff4-4491-b0e5-b386f32c0992&displaylang=en
3. The Utility software is located on the attached CD at
Napdos\DL_100\Utility.

DL-100T485 Quick Start V.104
DL-100T485 Utility Illustration
1. After lunching the Utility, the program interface would be
displayed, as shown below:
Clicking “File” or the icon opens a previous
DL-100T485 log data file stored on your PC.
Clicking “Connection->Connect->RS-232/RS-485” or the
icon creates a connection from the serial port.
Clicking “Connection->Disconnect” or the icon
disconnects the connection between the PC and the
DL-100T485.
Clicking *“Functions->Get Records” or the icon
retrieves the log data which is stored in the DL-100T485.
Clicking *“Functions->Configuration” or the icon
configures the DL-100T485.
Clicking “Exit” or the icon closes the Utility software.
*This function is only valid when the connection between the
PC and the DL-100T485 has been successfully established.

DL-100T485 Quick Start V.104
Connecting to the DL-100T485
1. Clicking the “ ” button will open the selection menu as
shown below:
2. Select your COM port number and set the Model Name
selection to the DL-100. If you are connecting to a new module,
the default address will be 01 and the checksum will be
disabled. Click the “OK” button to connect to the DL-100T485.
Note: The LCD will also indicate the module address and the
checksum status.
3. If the connection is successfully established, the Utility will
return to the previous window and the status bar will display
“Connection is established”. The “ ” and “ ” icons will also
become available.
4. If you want retrieve the records that are stored on the
DL-100T485, click the “ ” icon.
5. If you want configure the DL-100T485 click the “ ” icon.

DL-100T485 Quick Start V.104
Retrieving Records
After a connection between the PC and the DL-100T485 is
established, you can retrieve the log data via the Utility software.
The procedure is as follows:
1. Click the “Get” button and wait until the data is successfully
received.
2. The log data will be listed at the left side table and can be
opened the trend chart by clicking the “Show chart”. Refer to
the following picture for details.

DL-100T485 Quick Start V.104
Configuration
After the connection between the PC and the DL-100T485 has
been established, click the “ ” icon to configure the DL-100T485.
The details are shown as follows:
1. A new menu window would be created and the current module
configurations will be displayed. After changing the values, click
the “Set” button to update the configurations of the module.
2. When you successfully connect to the DL-100 by using the
Utility software, this Utility software will disable the data log
function. If you need to the data log function, you need to
enable the data log function before you close the Utility
software.