ICP DAS USA VPD-142-H User manual

Technical support: servic[email protected] P1
VPD-142(N)-H/143(N)-H
Quick Start
v1.1, Jan. 2019
What’s in the box?
Related Information
Thanks for buying ICPDAS VPD-142(N)-H/143(N)-H device. This
shipping package contains the following items:
VPD-142(N)-H/143(N)-H x 1
Quick Start x 1 (This Document)
2.4 mm Screw Driver x 1
Panel Mounting kit x 1
If you are new to VPD-142(N)-H/143(N)-H, please read the
“Chapter 3. Getting Started”
of the TouchPAD Hardware User
Manual for detailed information about install the free development
tool –HMIWorks and how to create your first project.
Documents, such as the User Manuals, the API References,
etc.: http://ftp.icpdas.com/pub/cd/touchpad/document/
Free Development Software, HMIWorks v2.10.10 or above:
http://ftp.icpdas.com/pub/cd/touchpad/setup/
If you have any questions, please feel free to contact us via email.

Technical support: servic[email protected] P2
1 Appearance
Front View Bottom View Top View
2 Pin Assignments
Pin
Description
D2+
The positive data line of the RS-485 network
D2-
The negative data line of the RS-485 network
GND
Ground pin
RxD2
The pin of received data of the RS-232
TxD2
The pin of transmitted data of the RS-232
D1+
The positive data line of the RS-485 network
D1-
The negative data line of the RS-485 network
GND
Ground pin
RxD1
The pin of received data of the RS-232
TxD1
The pin of transmitted data of the RS-232
GND
Connected to the power supply’s ground pin
VDC
DC input Voltage (range: +12 V ~ +48 V)
F.G.
Frame Ground. F.G. is connected to the
inside EMI or ESD suppression circuits. Make
sure that F.G. is connected to the Earth
LED Indicator
Ethernet
Serial Port
USB
Rotary Switch
Rubber Keypad
Reset Button
XV-Board
(optional)

Technical support: servic[email protected] P3
3 Rotary Switch & Default Settings
The definition of the rotary switch (VPD-142(N)-H):
No
Mode
Description
0
Run Only
Run the program. (Default)
9
USB Force
Update
Update a new application to the TouchPAD
device through USB.
The definition of the rotary switch (VPD-143(N)-H):
No
Mode
Description
0
Run &
Update
(Ethernet)
This is a special run mode which is used in
the development stage. The TouchPAD
device can be updated by a PC from the
remote side through Ethernet. (Default)
1
Ethernet
Force
Update
While the application run on the TouchPAD
device seriously crashes, use this mode to
update a new application to the TouchPAD
device through Ethernet.
2
Run Only
Run the program.
9
USB Force
Update
Update a new application to the TouchPAD
device through USB.
Network Default Settings (VPD-143(N)-H)
IP Address
192.168.255.1
Subnet Mask
255.255.0.0
Gateway
192.168.0.1
4 First Use of the VPD 4.3”H Series
1. Connect wires as the below figure or prepare an Ethernet cable which
will be used to supply power through PoE if there’s a RJ-45 Ethernet port
on it. And set the rotary switch to 0 (At this point, the power is not yet
supplied).

Technical support: servic[email protected] P4
2. Supply power to the VPD-142(N)-H/143(N)-H , wait
for several seconds and then you can see the default
program run on it.
3. Try to touch on the icons on the bottom-right corner of the screen of
the VPD-142(N)-H/143(N)-H and you can find that VPD-142(N)-H/143(N)-H
switches to the setting pages.
5 Hardware Installation
The panel mounting of VPD-142(N)-H/143(N)-H
The DIN-rail Mounting of VPD-142(N)-H/143(N)-H
Insert the panel mounting
clips into the upper and lower
ventilation holes.
Screw the panel mounting
clips to the panel.
(Mounting Screw: M4 x 30L)
Use a flat-head screwdriver
to set rotary switch
PoE Switch
GND
VDC (+12-+48 V)
External Power

Technical support: servic[email protected] P5
VPD-142(N)-H/143(N)-H
快速入門指南
v1.1, 2019年1月
檢查配件
參考資訊
感謝您購買泓格的
VPD-142(N)-H/143(N)-H
產品。產品包裝內應包含
下列配件:
VPD-142(N)-H/143(N)-H x 1
產品須知 x 1 (本文件)
24 mm 螺絲刀 x 1
面板安裝組件 x 1
如果您是第一次使用
VPD-142(N)-H/143(N)-H，請參閱 TouchPAD 硬
體使用手冊的
“第3 章啟動 TouchPAD” 來了解如何安裝免費的開
發軟體
HMIWorks 並建立第一個專案以及更多詳細的相關資訊。
相關文件，如使用手冊、應用程式介面指南(API Reference) 等:
http://ftp.icpdas.com/pub/cd/touchpad/document/
免費開發軟體，HMIWorks 版本 2.10.10 或以上版本:
http://ftp.icpdas.com/pub/cd/touchpad/setup/
如有任何問題歡迎使用
E-mail
聯繫我們，我們將會為您提供完善的咨
詢服務。

Technical support: servic[email protected] P6
1 外觀
前配置圖 下配置圖 上配置圖
2 腳位定義
Pin
說明
D2+
RS-485 網路的正訊號線
D2-
RS-485 網路的負訊號線
GND
接地端
RxD2
RS-232 的接收資料腳位
TxD2
RS-232 的傳送資料腳位
D1+
RS-485 網路的正訊號線
D1-
RS-485 網路的負訊號線
GND
接地端
RxD1
RS-232 的接收資料腳位
TxD1
RS-232 的傳送資料腳位
GND
連到電源的接地端
VDC
直流電壓輸入 (範圍：+12 V ~ +48 V)
F.G.
機架接地，F.G. (連接到內部的 EMI 或ESD 保
護電路)，請接到大地
LED 指示燈
序列埠
旋轉開關
橡膠鍵盤
(僅有)
重啟按鈕
I/O 擴充卡
XV-Board (選購)
Ethernet
USB

Technical support: servic[email protected] P7
3 旋轉開關及出廠預設值
旋轉開關的配置模式定義 (VPD-142(N)-H):
No
模式
說明
0
Run Only
執行程式。(出廠預設)
9
USB Force
Update
透過 USB 更新程式。
旋轉開關的配置模式定義 (VPD-143(N)-H):
No
模式
說明
0
Run & Update
(Ethernet)
執行/更新程式，用於程式開發階段 (能
執行程式，也能進行更新)。(出廠預設)
1
Ethernet
Force Update
強制更新，當 TouchPAD 上的程式嚴重
毀損時可用此模式透過 Ethernet 更新。
2
Run Only
執行程式。
9
USB Force
Update
透過 USB 更新程式。
網路設定出廠預設如下表 (VPD-143(N)-H):
IP Address
192.168.255.1
Subnet Mask
255.255.0.0
Gateway
192.168.0.1
4 第一次使用 VPD 4.3”H 系列
1. 如左圖所示，將電源和接地線連接完成。或是有 RJ-45 的乙太網路接
孔，可以準備一條網路線，透過乙太網路供電 (PoE)。然後將旋轉開關
(Rotary Switch) 轉到 0 (此時尚未供電)。

Technical support: servic[email protected] P8
2. 開始供電給 VPD-142(N)-H/143(N)-H，等待約數秒
的開機時間，接著可以看到 VPD-142(N)-H/143(N)-H
執行出貨預附的程式如左圖所示。
3. 試著按一下 VPD-142(N)-H/143(N)-H 螢幕上面的
圖示， V PD-142(N)-H/143(N)-H 會切到其他的頁面。
5 硬體安裝
VPD-142(N)-H/143(N)-H 的面板安裝 (Panel Mounting)
VPD-142(N)-H/143(N)-H 導軌安裝 (DIN-rail Mounting)
於上下方的通風口，插
入面板固定鋁夾
使用
M4 x 30L
螺絲釘，鎖
緊固定面板及鋁夾
乙太網路供電
外部供電器
GND
VDC (+12-+48 V)
使用一字起子來配
置旋轉開關