ICP DAS USA PROFI-5045 User manual

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
1
PROFI-5053
PROFIBUS Remote I/O Module
Quick Start Guide
 Introduction
This user guide introduces the user how to implement the PROFI-5000
into their applications in a quick and easy way. Therefore, it only provides
the basic instructions. For more detail information about the PROFI -5000
module, please refer to the PROFI-5000 user manual in the ICP DAS
product CD or download it from ICP DAS web site.
 PROFI-5000 Connector and Pin Assignment
Pin No.
Signal
Meaning
3
B-Line
Receive/Transmit data – plus
5
GND
Power ground of active terminator
6
VP
Power 5 volt of active terminator
8
A-Line
Receive/Transmit data - minus
The PROFIBUS connector is a standard 9 -pin D-Sub connector, there are
only 4 pins used in PROFI-5000. The pins VP and GND support the 5 volt
power to active terminal resistor, and the A-Line and B-Line is the data bus.
Status Indicator
PROFI-5045/ PROFI-5050/ PROFI-5051/ PROFI-
5052/ PROFI-5053/ PROFI-5055/ PROFI-5060
It provides two types of status indicator, they are PWR
LED (Red) and RUN LED (Green).
Status Indicator
Meaning
Recommend solution
PWR ON
Master not Ready,
1. Check the address setting
&
Address not Match
of module and DP-master.
RUN OFF
or
2.
Sets the DP-Master to
Cfg Fault
operation mode.
3.
Make sure of the
consistency of Module
Selection.

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
2
PWR ON &
Module is in clear mode
N/A
RUN ON
or operation mode.
 PROFI-5017/ PROFI-5017C/ PROFI-5018/ PROFI-5024
It provides three types of status indicator, they are PWR
LED (yellow), ERR LED (red) and RUN LED (green).
When the power is supplied to module, PWR LED will
turn on; If CHK_CFG procedure is finished, RUN LED will
turn on and ERR LED will turn off. The table explains the
relationship between them.
Status Indicator
Meaning
Recommend solution
ERR ON &
Offline Mode
Check the address setting of
RUN OFF
module and DP-master.
ERR Flash(0.1 sec)
Stop Mode
Check the DP-Master is ready
to communicate with module.
Check the setting of module in
ERR Flash(0.5 sec)
Prm Fault
the master interface and make
sure of the consistency.
ERR Flash(1 sec)
Cfg Fault
Same as above
ERR ON & RUN
Clear Mode
Sets the DP-Master from clear
ON
mode to operation mode
ERR OFF &
Operate Mode
RUN ON
PWR &
Diag Exist
Check the Input/Output value
ERR Flash
(Diag. Msg.
that if exceed/under the limit
lnterlace(0.5 sec)
Request)

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
3
 Terminating Resistors
In order to minimize the reflection effect of the signal transmission, PROFIBUS
device has to fit with an active terminal resistor at both first node and last node.
The connection of active terminating resistors is shown in above circuit diagram.
The PROFI-5000 doesn’t have any terminating resistors inside. Therefore, users
must add the terminator in external. In general, PROFIBUS connector has
terminating resistors inside, and there is a switch to control the ON/OFF of the
terminating resistors, as shown below.
Terminator ON
Terminator OFF
Terminator Switch
 Node Address
According to PROFIBUS specification, the station address which from 0 to 126 is
valid, and the address 126 is a special address that supports the remote setting
SSA telegram from Class 2 DP-Master.
 PROFI-5045/ PROFI-5050/ PROFI-5051/ PROFI-5052/
PROFI-5053/ PROFI-5055/ PROFI-5060
-

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
4
-The figure shown above is the decimal rotary switch. It dominates
the node (station) address of PROFI-5000. The left side switch is
high nibble of address and the other one is low nibble of address.
- It doesn’t support SSA service for setting node address.
EX 1 : MSB = 2, LSB = 3, node address => (2*10+3) = 23
 PROFI-5017/ PROFI-5017C/ PROFI-5018/ PROFI-5024
- The figure shown above is the decimal rotary switch. It dominates
the node (station) address of PROFI-5000. The switch is which
labeled MSB is high nibble of address and the other one is low
nibble of address.
- Module applies the setting of rotary switch as its address if the
address is valid. While the address is invalid, module loads the pre-
saved value from EEPROM. Moreover, if the address is invalid
(126) again, module awaits the SSA telegram and applies it. (Note:
If you want to clear the setting stored at EEPROM, you just adjust
rotary switch to FF before the power supplied).
Rotary
Pre-saved address
SSA Telegram
PROFI-5017(C)
Switch(dec)
(EEPROM)
Station Address
0~125
Do not care
No Accept
Rotary Switch
126~254
0~125
No Accept
Pre-saved
address(EEPROM)
126(default)
Accept with
SSA Telegram and
address 0~125
save address to
EEPROM
127~254
impossible
N/A
255
Clear to 126
Accept with
SSA telegram and
address 0~125
save address to
EEPROM
EX 1 : MSB = 0, LSB = B, node address => (0*16+11) = 11
EX 2 : MSB =7, LSB = 9, node address => (7*16+9) = 121

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
5
 PROFI-5000 – Setting and Module installation
(example for SIMATIC Step 7)
The following steps can help users to set and apply the PROFI-5000.
1. Address Setting:
2. Load GSD file into the DP-Master Configuring software a.
Open HW Config
b. Select Option -> Install GSD files
c. Click “Browse” to select GSD file, and then click “Install”

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
6
d. Install OK
3. Select I/O modules
a. Choose PROFI-5000
b. add I/O module that you want to use.

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
7
c. Modify system parameters and module parameters(modify by user’s
preference)
 System parameters: Double click PROFI-5000
 Module parameters: Double click module
4. Download Setting and Program into DP-Master
Users load the setting and program into DP-Master, and let it go.
a. Select Station -> Save and Compile

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
8
b. Select PLC -> Download
After the procedure finish, DP-Master will establish the connection with
PROFI-5000 and execute program automatically. RUN_LED indicates the
status of connection that you can observe.

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
9
PROFI-5000 Quick Start (Version 2.1, June/2013) ------8