ICP DAS USA SG-3081 User manual

1
SG-3081 Isolated Current Input / Output Module
User’s Manual
Introduction
The SG-3081 is a current input to voltage or current output signal conditioning module. It has
1000Vdc three-way isolation for input, output and power. And it also can change the
input/output range via internal configuration switches.
The SG-3081 has an LED display to show whether the SG-3081 is functioning correctly and
has two VRs (Zero, Span) to calibrate the input/output range accuracy.
The bandwidth of the SG-3081 is typically 3KHz. It’s easy to mount the SG-3081 on a standard
DIN rail and can operate in environments with wide temperature range.
Specifications
Current input:
Unipolar: 0~20mA, 4~20mA
Input impedance: 250Ω
Voltage output:
Unipolar: 0~5V, 0~10V
Output impedance: <50Ω
Drive: 10mA (max.)
Current Output:
Current: 0 ~ 20mA, 4 ~ 20mA
Current load resistor: 0～500 Ω(Source)
General
Three-way isolation: 1000 Vdc
Accuracy: ±0.1% of full range (typical)
Operation temperature range:-25°C～75°C
Storage temperature range:-30°C～85°C
Operation bandwidth: 3KHz
Weight: 95.5 gram
Supply Voltage
Input Range: 10~30Vdc
@24Vdc (Typical)
Consumption: 1.61W (voltage output)
2.10W (current output)

2
Configuration
The terminal wiring for the SG-3081 is shown in Figure A. Positive power terminals pins 7 and
9 are internally connected, as are negative pins 10 and 12. Power can be connected through
the adjacent modules, making wiring much easier. The SG-3081 uses a power input range of
10~30Vdc.
Table 1 shows the switch positions used to configure the input and output range.
The I/O configuration switches are located inside the module. And can be accessed by
removing the DIN-rail bracket covers by sliding them in the direction shown in Figure B.
Range (SW1) Range (SW2) Jumper
SG3081
Input To Output
Range 1 2 3 4 5 6 1 2 3 4 5 6 7 8 1 2
4~20mA／4~20mA ◆◆◆ ◆
4~20mA／0~20mA ◆◆◆◆◆◆◆
4~20mA／0~10V ◆◆◆ ◆ ◆ ◆◆
4~20mA／0~5V ◆◆◆ ◆◆◆◆
0~20mA／0~20mA ◆◆◆ ◆
0~20mA／4~20mA ◆◆◆◆ ◆◆◆◆◆
0~20mA／0~10V ◆◆◆◆ ◆
0~20mA／0~5V ◆◆◆◆
◆：ON
Table1:Input to output range (SW1, 2, Jumper1, 2)
＊ Factory default setting
*

3
Calibration Procedure
1. Refer to figure C to adjust the offset value.
(1) Connect pin7 to the +24Vdc connection and pin 10 to GND.
(2) Connect pin8 and pin 11 to the meter.
(3) Use wire to connect pins 1 and 2.
(4) Changing the SW1 and SW2 depends on your Input/Output range. Watch the value of
the meter and adjust the VR1 (ZERO) value to the minimum value of this range.

4
2. Refer to figure D to adjust the gain value.
(1) Connect pin7 to the +24Vdc connection and pin 10 to GND.
(2) Connect pin8 and pin 11 to the meter.
(3) Connect pins 1 and 2 to input source.
(4) Changing the SW1 and SW2 depends on your input/output range. Watch the value of
the meter and adjust the VR2 (SPAN) value to the maximum value of this range.
Block Diagram

5
Dimensions