ICP DAS USA ISO-P32S32W User manual

- 1 -
Language English
Version V1.3
Update Feb.2009
………………………………………………
What’s on your package?
¾One ISO-P32S32W series card
¾One companion ISA CD (V2.6 or later)
¾One Quick Start Guide(This document)
………………………………………………
Installing Windows Driver
Follow those steps:
1. Setup the Windows driver. You can get the driver from:
CD:\NAPDOS\ISA\ISO\DLL\
http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/iso/dll/
2. Click “Next >”button to start installation.
3. Click “Next >” button to install driver into the default folder.
4. Click “Install” button to continue installation.
5. Select “NO, I will restart my computer later” and click “Finish”.
1
2
I
SO
-P
3
2
S
3
2W
Windows driver only support windows 98/NT/2000 and
XP/2003/vista 32-bit versions.

- 2 -
………………………………………………
I/O Base Address & Jumper Setting
¾The base address is set from SW1 DIP switch on
board:
¾JP3 IRQ selection
………………………………………………
Installing Hardware on PC
Follow those steps:
1. Shut down and power off your computer
2. Remove all covers from the computer
3. Select an empty ISA slot
4. Carefully insert your I/O card into the ISA slot
5. Replace the PC covers
6. Power on the computer
After powering-on the computer, continue next process.
3
4
ON
1 2 3 4 5 6
SW1: Base Address Address 1 2 3 4 5 6
*0x200 ON ON ON ON ON ON
0x208 ON ON ON ON ON OFF
0x210 ON ON ON ON OFF ON
0x218 ON ON ON ON OFF OFF
0x220 ON ON ON OFF ON ON
0x228 ON ON ON OFF ON OFF
: : : : : : :
0x2C0 ON OFF OFF ON ON ON
0x2C8 ON OFF OFF ON ON OFF
: : : : : : :
0x300 OFF ON ON ON ON ON
0x308 OFF ON ON ON ON OFF
: : : : : : :
* Default Base Address: 0x200
N.C 15 14 12 11 10 9 7 6 5 4 3 N.C
*Default IRQ: N.C (Not use IRQ)

- 3 -
………………………………………………
Adding Hardware
7. Add Hardware
7-1 Open the “Control Panel” by click the item “Start / Settings / Control
Panel”.
7-2 Double-click the item “Add/Remove Hardware” and click “Next >” button.
7-3 Select the item “Add/Troubleshoot a device” and click“Next >” button.
7-4 Select the item “Add a new device” and click “Next >” button.
7-5 Select the item “No, I want to select the hardware from a list” and click
“Next >” button.
7-6 Select the item “Other device” and click “Next >” button.
7-7 Click the “Have Disk…” button.
7-8 Click the “Browse…” button to select the Inf file default path is
C:\DAQPRO\ISO_Win2K\Inf and clicks the “OK” button.
7-9 Select the correct device from the “Models:” listbox and Click “Next >”
button.
7-10 The windows show to dialog box and Click the “OK” button to enter the
device’s properties settings.
8. Modify the device properties
8-1 Enter the “ICPDAS P32C32 Digital I/O Card Properties”.
8-2 Click the “ I/O Range ” and click the “Change setting” button to enter the
“Edit Input/Output Range”.
8-3 Set the I/O Range value for SW1 value.
8-4 Click the “ IRQ ” and click the “Change setting” button to enter the “Edit
Interrupt Request” .
8-5 Set the IRQ value for JP3 setting value.
8-6 Check the Conflict information for “ No devices are conflicting” and click
“OK”.
5
Adding hardware is used on Windows 2000/XP/2003/Vista
32 only. Windows 9X/Me/NT users can skip it.

- 4 -
9. Reboot the PC
The detail “add hardware” information. Please refer to :
CD:\NAPDOS\ISA\Manual\PCI_ISA_PnP_Driver_Installation_in_Win9x_2K_XP.pdf
………………………………………………
Pin Assignments
6
CON1: Pin assignment
CON2: Pin assignment
CON1: Pin assignment
2
6
4
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
1
19
29
27
25
23
21
37
35
33
31
3
5
7
9
17
15
13
11
39 40
38
DI 16
DI 22
DI 21
DI 20
DI 19
DI 18
DI 17
DI 23
DI 24
DI 25
DI 31
DI 30
DI 29
DI 28
DI 27
DI 26
DO 25
DO 31
DO 30
DO 29
DO 28
DO 27
DO 26
CON1 D/O External
Power (+)
DO 16 for High drive
DO 22
DO 21
DO 20
DO 19 for High drive
DO 18 for High drive
DO 17 for High drive
DO 23
DO 24
N.C.
N.C.
CON1 D/O External
Power GND (-)
CON1 D/O External
Power GND (-)
GND for High Drive
GND for High Drive N.C.
20
22
21
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
1
2
3
4
5
15
14
13
12
11
10
9
8
7
6
19
18
17
16
DI 10
DI 13
DI 12
DI 11
DI 14
DI 15
DI 0
DI 6
DI 5
DI 4
DI 3
DI 2
DI 1
DI 7
DI 8
DI 9
DO 0 for High drive
DO 1 for High drive
DO 2 for High drive
DO 3 for High drive
DO 4
DO 5
DO 6
DO 7
DO 8
DO 9
DO 10
DO 11
DO 12
DO 13
DO 14
DO 15
External
Power GND (-) External
Power GND (-)
GND for High Drive
GND for High Drive External
Power (+)
20
22
21
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
1
2
3
4
5
15
14
13
12
11
10
9
8
7
6
19
18
17
16
DI 26
DI 29
DI 28
DI 27
DI 30
DI 31
DI 16
DI 22
DI 21
DI 20
DI 19
DI 18
DI 17
DI 23
DI 24
DI 25
DO 20
DO 21
DO 22
DO 23
DO 24
DO 25
DO 26
DO 27
DO 28
DO 29
DO 30
DO 31
External
Power GND (-) External
Power GND (-)
DO 16 for
High drive
DO 16 for High drive
DO 17 for High drive
DO 18 for High drive
DO 19 for High drive
GND for High Drive
GND for High Drive
DB-40-Pin conversion
DB-37-Pin
Extension cable:
CA-4037W

- 5 -
¾Wiring Note:
To prevent the board damaged forever by overload, the
GND pins (CON2: pin 1/ 18/ 19/ 20, CON2: pin 1/ 18/ 19/
20) all must be connected with GND of External Power.
O.C Output Type & Notice
High Driving Channel:
Open collector N-channel Power FET (BPS75N). Max. Sink current (NPN) is 500mAfor
each channel. DO_0~3 & DO_16~19.
Low Driving Channel:
Open collector NPN/PNP Transistor. Max. Sink Current is 100mA for Each Channel
DO_4~15 & DO_20~31.
(Recommend: It is necessary to connect a diode in the output end as means of
preventing damage from the counter emf. If your External Device is inductive Load,
Ex. Rela
y
…
)

- 6 -
………………………………………………
Self-Test
1. Prepare for device:
¾DN-37(Optional) wiring terminal board.
¾Exterior power supply device. For example: DP-665(Optional)
2. Use DN-37 to connect the board CON2.
3. Connect the DI(0-15) with DO(0-15) respectively.
(Pin02 connect to Pin21 … Pin17 connect to Pin36)
4. Supply the External Power +24 V to External Power(+).
Supply the External Power GND to External Power GND(-)
and GND for High Drive.
(External +24 V connect to Pin37;
External GND connect to Pin01, Pin18, Pin19, Pin20)
7
DN-37 I/O Wiring
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
+24
V
GND
GND
+5 V
Exterior
CON2
CON1

- 7 -
5. Run the ISO-P32C32 sample program.
Get the file from(Default): C:\DAQPro\ISO_WinXXX\Demo\
6. Check number of the ISO-P32S32W, and test DIO
function.
7. Get DIO function test result.
1. The one
ISO-P32S32W had
successfully
installed to PC.
2. Select the
board number for
the ISO-P32S32W. It
starts from 0.
3. Click this
button to do
DIO test.
4. Check
channels [0-15]
output write value
and input read
value for identical.
Complete

- 8 -
………………………………………………
Additional Information
9ISO-P32S32W Series Card Product page:
http://www.icpdas.com/products/DAQ/pc_based/iso_p32s32w.htm
9DN-37(Optional) page:
http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
9DP-665(Optional) page:
http://www.icpdas.com/products/Accessories/power_supply/dp-665.htm
9Documents:
CD:\NAPDOS\ISA\ISO\manual
http://ftp.icpdas.com/pub/cd/iocard/isa/napdos/isa/iso/manual/
9Software:
CD:\NAPDOS\ISA\ISO
http://www.icpdas.com/download/isa/iso/index.htm
The ICP DAS Web Site
http://www.icpdas.com
Contact Us
[email protected]
Copyright ©2008 by ICP DAS Co., Ltd. All right are reserved
8
Technical support
Supplies and ordering information
Ways to enhance your device
FAQ
Application story