ICP DAS USA I-7570 User manual

I-7570 Serial to HART Converter - QuickStart (Dec/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
1
I-7570
Serial to HART Converter
Quick Start Guide
Product Website:
https://www.icpdas-usa.com/i_7570.html
1. Introduction
This quick start manual will guide users to implement the I-7570 module into their
applications in a quick and easy way. For the more detailed information, please refer to
the user’s manual in the Fieldbus_CD of ICP DAS (“CD:\hart\convert\i-7570\manual\i-
7570_usermanual.pdf”) for detail.
We will use an I-7570 module (as a HART master), one HART slave and one PC as the
example shown in Figure 1-1 and demonstrate how to use the I-7570 utility for I-module
configuration and HART communication test.

I-7570 Serial to HART Converter - QuickStart (Dec/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
2
2. Hardware Installation
Users may need to make a hardware setting before the application.
The detailed illustration is as below :
[ Step1: Connect Serial port & Set FW Operation Mode ]
Connect the serial port of the I-7570 to PC and set the dip-switch on
the back of I-7570 to the “Normal” position. Then turn on the I-7570
module power.
[ Step2: Check the LED Indication I-7570 ]
Check the PWR LED of I-7570 if it is always on. If yes, it means I7570 is working in the
“Firmware Operation” mode.
[ Step3: Enable or Disable the Terminator Resistor ]
There is a Jumper (JP4) at the I-7570 module, shown in Figure 2-1.
The jumper can provide HART network with 250 Ω (1/4 W) load resistor.
When the pin 1&2 of JP4 is connected, the resistor will connect to HART
network. When the pin 2&3 ofJP4 is connected, it will disconnect the
resistor from HART network. By default, the pin1&2 of JP4 is connected.

I-7570 Serial to HART Converter - QuickStart (Dec/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
3
3. Using I-7570 Utility
Step1: Turn on the power of I-7570, if the PWR LED of the I-7570 is always on, then it means the I-7570
converter is working in the “Firmware Operation” mode.
Step2: Run the “I-7570 Utility”, HC_Tool, and click the “Settings” item like Figure 3-1 to configure the
serial connection and HART command parameters. Figure 3-1: “Settings” function of HC_Tool

I-7570 Serial to HART Converter - QuickStart (Dec/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
4
Step3: Set the “Port Name” and “Auto Configure“ parameters like Figure 3-2.

I-7570 Serial to HART Converter - QuickStart (Dec/2019)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
5