ICP DAS USA I-7560 User manual

I-7560 USB to RS-232Converter- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
1
I-7560
USB to RS-232Converter
Quick Start Guide
Product Website:
http://www.icpdas-usa.com/i_7560.html
1. Introduction
The I-7560/I-7560U provides a Windows serial COM port via it's USB
connection and is compatible with new and legacy RS-232 devices. USB
Plug-and-Play allows easy serial port expansion and requires no IRQ, DMA,
or I/O port settings manually.
The I-7560/I-7560U features a full set of RS-232 modem data and control
signals (TxD, RxD, RTS, CTS, DSR, DTR, DCD, RI and GND) on it's PC
compatible DB-9 male connector. It also features a high-speed 115200 bps
transmission rate.
The I-7560/I-7560U is powered from the USB bus and no additional power
supply is needed.
2. System Network Configuration

I-7560 USB to RS-232Converter- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
2
3. Block Diagram

I-7560 USB to RS-232Converter- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
3
4.Driver Installation
Installing the Device
Download driver files and install
1. Package CD \Napdos\7000\756x\7560
2. http://www.icpdas-usa.com/documents/drivers/756x/756x.zip
The following steps will show how to install the device under Windows 7.
1. Power on your computer and boot to Windows.
2. Locate the USB port of your computer and plug in the I-7560.
3. Windows will detect the new device and will initiate the Found New Hardware Wizard
prompting you to install the software for the detected USB Device. Select to install from
a list or specific location. Click Next to continue.

I-7560 USB to RS-232Converter- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
4

I-7560 USB to RS-232Converter- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
5

I-7560 USB to RS-232Converter- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
6

I-7560 USB to RS-232Converter- QuickStart (Jan/2018)
ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
7
Verify driver installation
This section will show you on how to verify whether the I-7560 was properly installed.
You will also need to determine the COM port assignment made by Windows for the
USB to RS-232/422/485 converter.
Note: Before you connect the I-7560 for the first time, ensure that you do not attach any
serial devices to the converter. You must only connect the I-7560 itself.
To verify whether the device is properly installed and determine the COM port
assignment for the device:
1. Click “Start” > “Control Panel” > “Device Manager” button. Double-click on Ports
(COM & LPT). If the device was correctly installed, you should now see the I-
7560 USB-to-RS232 (COM10) device listing. This also means that Windows has
assigned the device to the COM10 port.
2. Once you have verified that the device has been properly installed, you may now
proceed to use the USB-to-RS232/422/485 Converter to connect to serial
devices. Attach the serial device to the serial port of the adapter and then
connect the USB connector to the USB port of your computer. Use the supplied
driver for the serial device if needed.