ICP ET-2242U User manual

Copyright © 2015 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail] Page: 1
Q
Qu ui ic ck k S St ta ar rt t
English / Jul. 2017 / Version 1.0
f
fo or r E ET T- -2 22 24 42 2U U M Mo od du ul le e
I
In ns st ta al ll li in ng g t th he e S So of ft tw wa ar re e
The eSearch Utility can be obtained from either the companion
CD-ROM or from the ICPDAS website, as indicated below:
CD:\NAPDOS\software\eSearch\Windows\
http://ftp.icpdas.com/pub/cd/6000cd/napdos/software/esearch/windows/
Double-click the “eSearch_vxxx_setup.exe”file icon to execute the driver installation.
Click the “Next>”button to start the installation.
Select the destination location. The default path is C:\ICPDAS\eSearch. Verify that the destination
path is correct and click the “Next>”button.
Click the “Next>”button to continue.
Click the “Finish”button to complete the installation.
2
2
2
W
Wh ha at t’ ’s s i in n t th he e S Sh hi ip pp pi in ng g P Pa ac ck ka ag ge e? ?
The package includes the following items:
ET-2242U Module Quick Start (This Document) Companion CD
1
1
1

Copyright © 2015 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail] Page 2
P
Pi in n A As ss si ig gn nm me en nt ts s a an nd d W Wi ir ri in ng g N No ot te es s
Pin Assignments:
Wire Connections:
Digital Output
ON State
Readback as 1
OFF State
Readback as 0
Sink
DOx
DO.COM
-
+
Load
DOx
DO.COM
-
+
Load
Source
DOx
DO.COM
-+
Load
DOx
DO.COM
-+
Load
3
3
3

Copyright © 2015 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail] Page 3
D
DO O M Mo od db bu us s A Ad dd dr re es ss se es s
The nDO parameters in the following Modbus Address Tables are as follows:
Model Name
Universal
DIO
Number of DO channels (nDO)
Number of DI channels(nDI)
ET-2242U
-
16
0
(0xxxx) DO Address:
Starting
Address
Points
Description
Bits Per
Point
Range
Access
Type
0
(0x00)
1 ~ nDO
Digital Output Channels
1
0 = Off
1 = On
R/W
60
(0x3C)
1
Saves specific data to Flash
(The access type for some registers is
labeled with an “E”)
1
1 = Clear
W
100
(0x64)
1 ~ nDO
Enables the PWM for all DO Channels
1
0 = Off
1 = On
(Default= 0)
R/W
235
(0xEB)
1 ~ nDO
Sets the Power-on value for all DO
Channels
1
0 = Off
1 = On
(Default= 0)
R/W/F
267
(0x10B)
1 ~ nDO
Sets the Safe value for all DO Channels
1
0 = Off
1 = On
(Default= 0)
R/W/F
“R”: Read, “W”: Write, “F”: Settings are recorded in flash by default, “E”: After writing DO[60] register, the
data will be stored in flash.
For detailed information related to DO Modbus Addresses, refer to Section 6.3 "Modbus
Register Table" in the ET-2200 User Manual, which can be found at:
CD:\NAPDOS\ET2200\document\
http://ftp.icpdas.com/pub/cd/6000cd/napdos/et2200/document/
4
4
4

Copyright © 2015 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail] Page 4
C
Co on nn ne ec ct ti in ng g t th he e P Po ow we er r a an nd d t th he e H Ho os st t P PC C
Ensure that the network settings on the Host PC have been correctly configured and are
functioning normally. Ensure that the Windows firewall or any Anti-Virus firewall is properly
configured to allow incoming connections, or temporarily disable these functions, otherwise the
“Search Servers” function in the eSearch Utility described in Section 7 may not perform as expected.
Contact the System Administrator for instructions of how to do this.
Connect both the ET-2242U module and the Host PC to the same sub network or the same
Ethernet Switch.
Apply power to the ET-2242U module. The valid power voltage range is from +10 to +48 VDC.
Verify that the “PWR”LED indicator on the ET-2242U
module is flashing.
5
5
5

Copyright © 2015 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail] Page 5
W
Wi ir ri in ng g t th he e D DO O f fo or r S Se el lf f- -T Te es st t
A tip for connecting the wire to the connector
A tip for removing the wire from the connector
Use output LED to connect the DO.COM (Pin04) and DO0 (Pin06).
Connect the External Power +24V to the DO0 (Pin06).
Connect the External Power GND to the DO.COM (Pin04).
6
6
6
1. Use the blade of the
flat-head screwdriver to
push down the wire
clamp.
Insert the wire
Continue holding the
screwdriver in place
2. While holding the
screwdriver in place,
insert the wire into the
terminal block.
1. Use the blade of a
flat-head screwdriver to
push down the wire
clamp.
Remove the wire
Continue holding the
screwdriver in place
2. While holding the
screwdriver in place,
remove the wire from the
terminal block.

Copyright © 2015 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail] Page 6
C
Co on nf fi ig gu ur ri in ng g t th he e C Co or rr re ec ct t N Ne et tw wo or rk k S Se et tt ti in ng gs s
Execute the eSearch Utility and click the “Search Servers” button to search for the ET-2242U.
Once the search process in complete, double-click the name of the ET-2242U to open the
“Configure Server (UDP)” dialog box.
Enter the relevant values for the IP Address, Subnet Mask and Gateway, etc., and then click the
“OK” button. The new settings for the ET-2242U will take effect within 2 seconds. If the correct
network configuration information is unknown, contact the Network Administrator to obtain the
relevant details.
Wait for 2 seconds and then click the “Search Servers” button again to ensure that the ET-2242U is
operating correctly using the new configuration.
Click the name of the ET-2242U to select it.
Click the “Web”button to log in to the web configuration pages.
7
7
7
Factory Default Settings for
the ET-2242U Series:
IP
192.168.255.1
Gateway
192.168.0.1
Mask
255.255.0.0







Copyright © 2015 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail] Page 7
P
Pe er rf fo or rm mi in ng g t th he e S Se el lf f- -T Te es st t
Once the login screen is displayed, enter the password in the login password field (use the default
password is “Admin”), and then click the “Submit” button to enter the configuration web page.
The main (Home) page will be displayed, this page allows a simple test to be performed to verify
the Digital Output functionality.
Click the DO0 button.
8
8
8


Factory Default
Password: Admin


Copyright © 2015 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail] Page 8
V
Ve er ri if fy yi in ng g t th he e T Te es st t
The DO0 indicators will turn red when DO0 is ON.
Verify that the DO0 of output LED status for “high”.
9
9
9
R
Re el la at te ed d I In nf fo or rm ma at ti io on n
ET-2242U Product Page:
http://www.icpdas.com/root/product/solutions/remote_io/ethernet_io/petl-7000_tpet_tet/et-2242.html
Documentation & Firmware:
CD:\Napdos\ET2200
http://ftp.icpdas.com/pub/cd/6000cd/napdos/et2200/
NS-205 and DP-665 Product Page (Optional):
http://www.icpdas.com/root/product/solutions/industrial_ethernet_switch/ns-205.html
http://www.icpdas.com/products/Accessories/power_supply/dp-665.htm
