ICRealtime ICR2200 User manual

INSTRUCTION MANUAL Ver 1.1
Outdoor High Speed Dome Camera

Speed Dome Camera Instruction Manual 2/47
This lightning flash with arrowhead symbol is intended to alert the user to the
presence of un-insulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
This exclamation point symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.

Speed Dome Camera Instruction Manual 3/47
Important Safeguard
1. Read Instructions
Read all of the safety and operating instructions before using the product.
2. Retain Instructions
Save these instructions for future reference.
3. Attachments / Accessories
Do not use attachments or accessories unless recommended by the appliance manufacturer as they may
cause hazards, damage product and void warranty.
4. Installation
Do not place or mount this product in or on an unstable or improperly supported location. Improperly
installed product may fall, causing serious injury to a child or adult, and damage to the product. Use only
with a mounting device recommended by the manufacturer, or sold with the product. To insure proper
mounting, follow the manufacturer's instructions and use only mounting accessories recommended by
manufacturer.
5. Power source
This product should be operated only from the type of power source indicated on the marking label.
Precautions
Operating
zBefore using, make sure power supply and others are properly connected.
zWhile operating, if any abnormal condition or malfunction is observed, stop using the camera
immediately and then contact your local dealer.
Handling
zDo not disassemble or tamper with parts inside the camera.
zDo not drop or subject the camera to shock and vibration as this can damage camera.
zCare must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin your
quality of camera.
Installation and Storage
zDo not install the camera in areas of extreme temperature, which exceed the allowable range.
zAvoid installing in humid or dusty places.
zAvoid installing in places where radiation is present.
zAvoid installing in places where there are strong magnetic fields and electric signals.
zAvoid installing in places where the camera would be subject to strong vibrations.
NOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICENOTICE

Speed Dome Camera Instruction Manual 4/47
○
1Introduction
Features 5
Product&Accessories 7
PartsName&Functions 8
○
2Installation
DIPSwitchSetup 9
InstallationusingWallMountBracket 11
Installation using Ceiling Mount Bracket 12
Cabling 14
○
3Operation
CheckingBeforeOperation 16
PresetandPatternFunctionPre-Check 16
Start OSD Menu
17
Reserved Preset
17
Preset
18
Swing
18
Pattern
19
Group
20
Other Motion Functions
21
OSD Display of Main Screen
22
○
4How to use OSD Menu
General Rules of Menu Operation
23
Main Menu
23
Display Menu for Main Screen
24
Privacy Zone Mask Setup
25
Camera Module Setup
26
Motion Setup
34
Preset Setup
36
Swing Setup
39
Pattern Setup
40
Group Setup
41
System Initialization
43
○
5Specifications
44
Dimension
47
CONTENTS

Speed Dome Camera Instruction Manual 5/47
Feature s
Camera Specifications
zCCD Sensor : 1/4" SONY Super HAD CCD →×22, ×30 Model
1/4" SONY EXView CCD →×26 Model
zZoom Magnification : ×22 Optical Zoom, ×10 Digital Zoom (Max ×220 Zoom) →×22 Model
×30 Optical Zoom, ×10 Digital Zoom (Max ×300 Zoom) →×30 Model
×26 Optical Zoom, ×12 Digital Zoom (Max ×312 Zoom) →×26 Model
zDay & Night Function
zVarious Focus Mode : Auto-Focus / Manual Focus / Semi-Auto Focus.
zIndependent & Simultaneous Camera Characteristic Setup in Preset operation
Powerful Pan/Tilt Functions
zMax. 360°/sec high speed Pan/Tilt Motion
zUsing Vector Drive Technology, Pan/Tilt motions are accomplished in a shortest path. As a result,
time to target view is reduced dramatically and the video on the monitor is very natural to watch.
zFor jog operation using a controller, since ultra slow speed 0.05°/sec can be reached, it is very easy
to locate camera to desired target view. Additionally it is easy to move camera to a desired position
with zoom-proportional pan/tilt movement.
Preset, Pattern, Swing, Group, Privacy Mask and More…
zMAX. 127 Presets are assignable and characteristics of each preset can be set up independently,
such as White Balance, Auto Exposure, Label, Digital Outputs and so on.
zMax. 8 set of Swing action can be stored. This enables to move camera repetitively between two
preset positions with designated speed.
zMax. 4 of Patterns can be recorded and played back. This enables to move camera to follow any
trajectory operated by joystick as closely as possible.
zMax. 8 set of Group action can be stored. This enables to move camera repetitively with
combination of Preset or Pattern or Swing. A Group is composed of max. 20 entities of
Preset/Pattern/Swings.
zPrivacy Masks are assignable, not to intrude on other’s privacy. (8 Privacy Zones)
→The availability for Privacy Mask function should be different by models.
PTZ(Pan/Tilt/Zoom) Control
zWith RS-485 communication, max. 255 of cameras can be controlled at the same time.
zPelco-D or Pelco-P protocol can be selected as a control protocol in the current version of firmware.
INTRODUCTION 1

Speed Dome Camera Instruction Manual 6/47
OSD(On Screen Display) Menu
zOSD menu is provided to display the status of camera and to configure the functions interactively.
zThe information such as Camera ID, Pan/Tilt Angle, Alarm I/O and Preset can be displayed on
screen.
Alarm I/O Functions
z4 alarm sensor Inputs and 2 alarm Output relays are available.
zTo reject external electric noise and shock perfectly, alarm sensor Input is decoupled with photo
coupler and the relay is used for alarm output.
zThe signal range of sensor input is from DC 5.0 to 12.0 volts to adopt various applications.
Meanwhile, the maximum load of relay contact is AC 250V, 3A or DC 28V, 3A.
zIf an external sensor is activated, camera can be set to move to the corresponding Preset position.
Meanwhile, the output relay can be matched to some specific Preset positions to do counteractions
such as turning on the light or sound the alarm.
Reserved Presets for Special Purpose
zMost camera characteristics can be set up easily and directly with reserved preset, not entering
into OSD menu. For more information, refer to “Reserved Preset” in this manual.
Easy Installation and Perfect Outdoor Environment Compatibility
zFans and heaters are built-in in camera for cold and hot temperature environment. Also idealistic
mechanical design protects camera from water and dust. (IP 66)
zIt is easy to install and maintain camera with terminal for cable connection in brackets.
INTRODUCTION 1

Speed Dome Camera Instruction Manual 7/47
Product & Accessories
Product & Accessories
zMain Body * zMain Body (Sun-Shield) * zDome Cover
zWall mount bracket ** zCeiling Mount Bracket ** zScrews
Options
zPole Mount Adapter zCornor Mount Adapter
INTRODUCTION 1

Speed Dome Camera Instruction Manual 8/47
Parts Name & Functions
Main Body
Cable
DIP Switch
Lockup Screw
Drop Prevention
Spring
Cabling
Terminal Bloc
k
Fuse
Main Body
Connector
Mold Line
zMain Body zMount Bracket
zDome Cover Do not detach protection vinyl from dome cover before finishing all
installation process to protect dome cover from scratches or dust.
zDIP Switch Sets up camera ID and protocol.
zMain Body Cable
Main Body Connector
Enables signals and power to come and go between main body and
mount bracket.
zDrop Prevention Spring This part keeps the camera from dropping during installation and
maintenance. After install the Bracket, please, hang the spring to the
drop prevention hook of main body as shown in picture for further
tasks.
zLockup Screw After assembling main body to bracket, screw main body to bracket to
protect them from separation by vibration and so on.
zFuse If the fuse is burnt to protect your came from over-current damage, the
fuse have to be replace with new one. The fuse specification is 250V 3A.
However, we recommend consulting with supplier to remove the cause
of over-current.
zCabling Terminal Block During installation, Power, Video, Communication, Alarm I/O cables are
connected on to this cabling terminal block.
zMold Line Mark to assemble main body to bracket.
INTRODUCTION 1

Speed Dome Camera Instruction Manual 9/47
DIP Switch Setup
Before you install the camera, you should set the DIP switches to configure the camera ID, communication
protocol.
ON ON
PROT0
ID0
1818
PROT1 PROT2
ST0
ST1 ST2 ST3
ID7
CAM ID
Communication
Protocol Camera ID
Camera ID Setup
123456
ON
ON
78
zID number of camera is set using binary number. The example is
shown bellow.
Pin 1 2 3 4 5 6 7 8
ID Value 1 2 4 8 16 32 64 128
ex) ID=5 on off on off off off off off
ex) ID=10 off on off on off off off off
zThe range of ID is 1~255. Do not use 0 as camera ID. Factory
default of Camera ID is 1.
zIf you want to control a certain camera, you must match the camera
ID with Cam ID setting of DVR or Controller.
INSTALLATION 2

Speed Dome Camera Instruction Manual 10/47
Communication Protocol Setup
123456
ON
ON
78
Sensor Type Setup
123456
ON
ON
78
zSelect the appropriate Protocol with DIP switch combination.
Switch State
P0
(Pin 1)
P1
(Pin 2)
P2
(Pin 3)
Protocol/Baud rate
OFF OFF OFF PELCO-D, 2400 bps
ON OFF OFF PELCO-D, 9600 bps
OFF ON OFF PELCO-P, 4800 bps
ON ON OFF PELCO-P, 9600 bps
Otherwise Reserved
zIf you want to control using DVR or P/T controller, their protocol must
be identical to camera. Otherwise, you can not control the camera.
zIf you changed camera protocol by changing DIP S/W, the change
will be effective after you reboot the camera.
zFactory default of protocol is “Pelco-D, 2400 bps”.
zIf you want to use Alarm Input, the types of sensor must be selected.
The sensor types are Normal Open and Normal.
~Normal Open Output Voltage is high state when sensor is
activated.
~Normal Close Output Voltage is high state when sensor is not
activated.
Pin No Switch State Sensor Type
ON Sensor 1 : Normal Close Type
ST0 (Pin 4)
OFF Sensor 1 : Normal Open Type
ON Sensor 2 : Normal Close Type
ST1 (Pin 5)
OFF Sensor 2 : Normal Open Type
ON Sensor 3 : Normal Close Type
ST2 (Pin 6)
OFF Sensor 3 : Normal Open Type
ON Sensor 4 : Normal Close Type
ST3 (Pin 7)
OFF Sensor 4 : Normal Open Type
zIf sensor type is not selected properly, the alarm can be activated
reversely.
INSTALLATION 2

Speed Dome Camera Instruction Manual 11/47
Installation using Wall Mount Bracket
①Install Wall Mount Bracket on wall.
②Wire cables to terminal blocks on the PCB in Wall
Mount Bracket.
③Hook up “Drop Prevention Spring” on main body
to prevent camera from unexpected drop and
connect Main Body Cable to Main Body
Connector in Wall Mount Bracket.
④ Line up the mold lines and assemble main body
to Wall Mount Bracket.
⑤Turn main body on its axis in CW(Clockwise)
direction and, after assembling them, screw main
body to Wall Mount Bracket to protect them from
separation by vibration or others.
⑥ In case of using pipe, use the hole located on
lower side of Wall Mount Bracket to fix pipe.
INSTALLATION 2

Speed Dome Camera Instruction Manual 12/47
Installation using Ceiling Mount Bracket
①To pass cables to upside of ceiling, please make a
hole with 50~60mm diameter on the ceiling panel
and attach the Ceiling mount bracket on it.
②Wire cables to terminal blocks on the PCB in
Ceiling Mount Bracket.
③Hook up “Drop Prevention Spring” on main body
to prevent camera from unexpected drop and
connect Main Body Cable to Main Body
Connector in Ceiling Mount Bracket.
④ Line up the mold lines and assemble main body
to Ceiling Mount Bracket.
INSTALLATION 2

Speed Dome Camera Instruction Manual 13/47
⑤Turn main body on its axis in CW(Clockwise)
direction and, after assembling them, screw main
body to Ceiling Mount Bracket to protect them
from separation by vibration or others.
INSTALLATION 2

Speed Dome Camera Instruction Manual 14/47
Cabling
RS-485
BNC
PWR+
PWR-
VIDEO(+)
VIDEO(-)
RS-485+
RS-485-
RELAY1
COMMON+
SEN1
SEN2
SEN3
SEN4
Braket Terminal Block
Moinitor
Controller
/ DVR
Power
Light
Alarm
Buzzer
Sensor
Output Devices
IrDA
Sensor
Door
Switch
RELAY2
Power Connection
zPlease, check the voltage and current capacity of rated power carefully. Rated power is indicated in the
back of main unit.
Rated Power Input Voltage Range Current Consumption
DC 12V DC 11V ~ 18V 2.5 A
AC 24V AC 17V ~ 29V 1.5 A
Video Connection
zConnect with BNC coaxial cable.
 RS-485 Communication
zFor PTZ control, connect this line to keyboard and DVR. To control multiple cameras at the same time,
RS-485 communication lines of them is connected in parallel as shown below.
K
eyboard Controller / DVR
RS-485
+
-
#1
+
-
#2
+
-
#n
+
-
INSTALLATION 2

Speed Dome Camera Instruction Manual 15/47
Alarm I/O Connection
zSensor Input
Before connecting sensors, check driving voltage and output signal type of the sensor. Since output
signal types of the sensors are divided into Open Collector and Voltage Output type in general, the
cabling must be done properly after considering these typed. Also, the sensor type, i.e. “Normal Open”
or “Normal Close” in Dip switch in main body of camera must be set properly.
Signal Description
IN COM+ Connect (+) cable of electric power source for Sensors to this port as
shown in the circuit above.
IN1−, IN2−, IN3−, In4−Connect output of sensors for each port as shown in the circuit above.
zRelay Output
OUT 1
AC or DC
OUT 2
AC or DC
Internal
LOAD
LOAD
Maximum allowable electrical load of relay is shown bellow table.
Drive Power DC Power AC 110V Power AC220V Power
Max. Load DC 28V, 3A AC110V, 3A AC250V, 3A
IN COM+
Internal +5V~12V
IN 1-
IN 4-
Sensor 1 Output
+
+
-
-
+
-
Sensor 4 Output
INSTALLATION 2

Speed Dome Camera Instruction Manual 16/47
Check points before operation
zBefore power is applied, please check the cables carefully.
zThe camera ID of the controller must be identical to that of the target camera. The camera ID can be checked
by reading DIP switch of the camera.
zIf your controller supports multi-protocols, the protocol must be changed to match to that of the camera.
zIf you changed camera protocol by changing DIP switch, the change will be effective after you reboot the
camera.
zSince the operation method can be different for each controller available, refer to the manual for your
controller if camera can not be controlled properly. The operation of this manual is based on the standard
Pelco® Controller.
Preset and Pattern Function Pre-Check
zCheck how to operate preset and pattern function with controller or DVR in advance to operate camera
function fully when using controller or DVR.
zRefer to the following table when using standard Pelco® protocol controller.
< Go Preset > Input [Preset Number] and press [Preset] button shortly.
< Set Preset > Input [Preset Number] and press [Preset] button for more than 2 seconds.
< Run Pattern > Input [Pattern Number] and press [Pattern] button shortly.
< Set Pattern > Input [Pattern Number] and press [Pattern] button for more than 2 seconds.
zIf controller or DVR has no pattern button or function, use shortcut keys with preset numbers. For more
information, refer to “Reserved Preset” in this manual.
OPERATION 3

Speed Dome Camera Instruction Manual 17/47
Starting OSD Menu
zFunction Using the OSD menu, Preset, Pattern, Swing, Group and Alarm I/O function can be
configured for each application.
zEnter Menu <Go Preset> [95]
Reserved Preset
zDescription Some Preset numbers are reserved to special functions.
zFunction <Go Preset> [95] : Enters into OSD menu
<Go Preset> [131~134] : Runs Pattern Function 1 ~ 4
<Go Preset> [141~148] : Runs Swing Function 1 ~
<Go Preset> [151~158] : Runs Group Function 1 ~ 8
<Go Preset> [161~162] : Sets Relay Output 1 ~ 2 to OFF
<Set Preset> [161~162] : Sets Relay Output 1 ~ 2 to ON
<Go Preset> [170] : Sets Camera BLC Mode to OFF
<Go Preset> [171] : Sets Camera BLC Mode to ON
<Go Preset> [172] : Sets Camera Flickerless Mode to OFF
<Go Preset> [173] : Sets Camera Flickerless Mode to ON
<Go Preset> [174] : Sets Camera Focus Mode to AUTO
<Go Preset> [175] : Sets Camera Focus Mode to Manual
<Go Preset> [176] : Sets Camera Focus Mode to SEMI-AUTO
<Go Preset> [177] : Sets Day & Night Mode to AUTO
<Go Preset> [178] : Sets Day & Night Mode to NIGHT
<Go Preset> [179] : Sets Day & Night Mode to DAY
<Go Preset> [180] : Sets Line-Lock Mode to OFF
<Go Preset> [181] : Sets Line-Lock Mode to ON
<Go Preset> [190] : Sets OSD Display Mode to AUTO (Except Privacy Mask)
<Go Preset> [191] : Sets OSD Display Mode to OFF (Except Privacy Mask)
<Go Preset> [192] : Setting OSD Display Mode to ON (Except Privacy Mask)
<Go Preset> [193] : Sets all Privacy Mask Display to OFF
<Go Preset> [194] : Sets all Privacy Mask Display to ON
OPERATION 3

Speed Dome Camera Instruction Manual 18/47
Preset
zFunction Max. 127 positions can be stored as Preset position. The Preset number can be assigned
from 1 to 128, but 95 is reserved for starting OSD menu.
Camera characteristics (i.e. White Balance, Auto Exposure) can be set up independently
for each preset. Label should be blank and Relay Outputs should be set to OFF as default.
All characteristics can be set up in OSD menu.
zSet Preset <Set Preset> [1~128]
zRun Preset <Go Preset> [1~128]
zDelete Preset To delete Preset, use OSD menu.
Swing
zFunction By using Swing function, you can make camera to move between 2 Preset positions
repeatedly. When swing function runs, camera moves from the preset assigned as the 1st
point to the preset assigned as the 2nd point in CW(Clockwise) direction. Then camera
moves from the preset assigned as the 2nd point to the preset assigned as the 1st point in
CCW(Counterclockwise) direction.
In case that the preset assigned as the 1st point is same as the preset assigned as the 2nd
point, camera turns on its axis by 360°in CW(Clockwise) direction and then it turns on its
axis by 360°in CCW(Counterclockwise) direction.
Speed can be set up from 1°/sec to 180°/sec.
zSet Swing To set Swing, use OSD menu.
zRun Swing Method 1) <Run Pattern> [Swing NO.+10]
Method 2) <Go Preset> [Swing NO.+140]
ex) Run Swing 3 : <Run Pattern> [13]
ex) Run Swing 3 : <Go Preset> [143]
zDelete Swing To delete Swing, use OSD menu.
1st Preset
2nd Preset
1CWDirection
2CCWDirection
OPERATION 3

Speed Dome Camera Instruction Manual 19/47
Pattern
zFunction Pattern Function is that a camera memorizes the path (mostly curve path) by joystick of
controller for assigned time and revives the path exactly as it memorized.
4 Patterns are available and Maximum 1200 communication commands can be stored in
a pattern.
zSet Pattern Pattern can be created by one of following two methods.
Method 1) <Set Pattern> [Pattern NO.]
{Pattern editing screen is displayed as bellow.
EDIT PATTERN 1
[NEAR:SAVE /FAR:DELETE]
0/0/x1/N
{Movement by Joystick and preset movement can be memorized in a pattern.
{The rest memory size is displayed in progress bar.
{To save the recording, press NEAR key and to cancel, press FAR key.
Method 2) OSD Using OSD Menu: See the section “How to use OSD Menu”.
zRun Pattern Method 1) <Run Pattern> [Pattern NO.]
Method 2) <Go Preset> [Pattern NO.+130]
ex) Run Pattern 2 : <Run Pattern> [2]
ex) Run Pattern 2: <Go Preset> [132]
zDelete Pattern Use OSD menu to delete a Pattern.
OPERATION 3

Speed Dome Camera Instruction Manual 20/47
Group
zFunction The group function allows running sequence of Presets, Pattern and/or Swings. Max 8
group can be stored. Each group can have max 20 action entities which can be preset,
pattern or swing. Preset speed can be set up and the repeat number of Pattern & Swing
can be set up in Group setup. Dwell time between actions can be set up also.
Preset 1 Pattern 1 Swing 1
Dwell Time
Max 20 Entities
zSet Group Use OSD Menu to create a Group.
zRun Group Method 1) <Run Pattern> [Group NO.+20]
Method 2) <Go Preset> [Group NO.++150]
ex) Run Group 7 : <Run Pattern> [27]
ex) Run Group 7 : <Go Preset> [157]
zDelete Group Use OSD Menu to delete.
OPERATION 3