ICT Bill Validator S6 Series User manual

4 - Way Acceptance
Low Maintenance
Easy Installation
Re - Programmable
Flash ROM
Auto Self -Adjusting
Sensor System
Saving Power
2003 International Currency Technologies Corporation
Vol. 8.0 Part Number : H4512G-R
B V or
ill alidat B V or
ill alidat
S6 Series
Installation Guide

S6 Bill Validator Specifications ....................................... 2
The Front LED ................... ............................................. 4
The Back LED Status ...................................................... 4
S6 Pin-out Assignments (M.D.B. for 12 V DC) ....................... 5
S6 Pin-out Assignments (Service Pulse for 12 V DC) .............. 6
S6 Wake up Signal ........................................................... 7
S6 Service Signal ............................................................. 7
S6 Service Signal for ICA Only ......................................... 8
Cable ............................................................................... 9
Switch Settings ....................................................(Appendix)
ContentsContents

S6 Bill Validator Specifications
Acceptance Rate
Bill insertion
Acceptance Speed
Interfaces
Bill box Capacity
Power Sources
Weight
Environment Range
96% or greater
4-way Acceptance
Approx. 3 seconds (including bill stacking)
Pulse
Approx. 300 bills (200~300)
500 bills (300~500)
800 bills (750~850)
12V DC ± 10% (9V ~15V DC)
( ) We recommend the input has to be 12V DC.
If the input is lower than 9V DC, the machine may be shut down.
If the input is higher than 15V DC, the machine may be break down.
Power Consumption
Approx. 2kg (shipping)
Operating Temperature : -10 C~50 C
Storage Temperature : -30 C~70 C
- 2 -
Humidity : 30%~85% RH (no condensation)
Action mode 12V , 2A (peak), 650mA (average)
Standby mode 9V~15V DC
Power saving mode 12V , approx. 40 A
94.0(3.70")
235.9(9.29")
130.0(5.12") 500bills
107.0(4.21")
48.1(1.90")
13.0(0.51")
129.0(5.08")
50.8(2.00")
115.0(4.53")
115.0(4.53") 300bills
500 pcs.
300 pcs.
800 pcs.
190.0(7.48") 800bills
94.0(3.70")
245.4(9.66")
130.0(5.12') 500bills
115.0(4.53") 300bills
500 pcs.
300 pcs.
107.0(4.21")
48.1(1.90)
13.0(0.51")
132.0(5.20")
116.0(4.57")
50.8(2.00")
84.0(3.31")
800 pcs.
190.0(7.48") 800bills
- 3 -
S6
Unit : :mm
( ) : in

- 4 -
The two LED lights located at the front of the unit will show the operational
status of the bill validator. The LED lights will flash ON and OFF (in 500ms
intervals) when the unit is ready to accept bills. The LED lights will be OFF
if the unit is disabled, out of service or in power saving mode.
The bill validator can only accept one bill at a time. The LED lights will be
OFF and will not accept another bill while a bill is being validated in the unit.
The LED lights will start to flash normally when the bill validator is ready to
accept the next bill. In power saving mode, although the LEDs are off, the
bill validator in still ready for accepting a bill.
The Front LED
The Back LED Status
Figure 1
Option Switches LED
Note:
In addition to the 30-pin connector, there is also an 8-pin RJ-45 connector on
the side of the bill validator designed for the purpose of downloading programs
and updating validation software. The connector will be kept open under
normal operation of the bill validator. It will only be used when a new software
or programs need to be downloaded into the flash ROM. The pin-out
assignments of the 8-pin RJ-45 connector are as follows:
Pin 1 - GND Pin 5 - /RESET
Pin 2 - TXD2 Pin 6 - VCC
Pin 3 - RXD2 Pin 7 - RXD1
Pin 4 - PROGRAM Pin 8 - TXD1
Option Switches LED
DIAGNOSTICS (GREEN LED)
LED LED OFF=POWER OFFON=OK
FLASHES STATUS
1 bill jammed
2 disabled from system
3 sensor problem
4 reserved
5 bill box is removed
6 bill box is full of money
- 5 -
For the MDB interface S6 bill validator, connect the 30-pin peripheral connector
on one end of the harness to the side of the unit and the standard 6-pin MDB
connector to the power/interface connector.
The standard 6-pin MDB connector pin-out assignments:
Pin 1 - +12 VDC (POWER IN)
Pin 2 - GND (POWER RETURN)
Pin 3 - WAKE_UP
Pin 4 - MASTER RECEIVE (MDB_MASTER_RxD)
Pin 5 - MASTER TRANSMIT (MDB_MASTER_TxD)
Pin 6 - COMMUNICATIONS COMMON (MDB_GND)
Dual-in-line 30-pin peripheral connector (S6, MDB) pin-out assignments:
S6 Pin-out Assignments (M.D.B. System for 12V DC)
1 2 3 4 5 6 7 8 9 10
2519
11
2620
12
2721
13
282216
14
292317
15
302418
456
3
2
1
CAUTION: Turn off the power before connecting or disconnecting the
bill validator.
Pin 16 - Reserved
Pin 17 - WAKE_UP
Pin 18 - Reserved
Pin 19 - Reserved
Pin 20 - GND
Pin 21 - Reserved
Pin 22 - Reserved
Pin 23 - Reserved
Pin 24 - Reserved
Pin 25 - Reserved
Pin 26 - Reserved
Pin 27 - Reserved
Pin 28 - MDB_GND
Pin 29 - Reserved
Pin 30 - Reserved
Pin 1 - Reserved
Pin 2 - Reserved.
Pin 3 - +12 VDC
Pin 4 - Reserved
Pin 5 - Reserved
Pin 6 - MDB_MASTER_RxD
Pin 7 - Reserved
Pin 8 - Reserved
Pin 9 - Reserved
Pin 10 - Reserved
Pin 11 - Reserved
Pin 12 - Reserved
Pin 13 - Reserved
Pin 14 - MDB_MASTER_TxD
Pin 15 - Reserved
Cable Order No. : WEL-V705(3-BA-A7V7-51)
*

- 7 -
S6 Service Signal (It works like a switch)
1. Condition 1 : When B.A. wakes up and does not take any bill.
2. Condition 2 : When B.A. takes a true bill.
3. Condition 3 : When B.A. rejects a fake note.
Close
Close
Close
Sleep
Sleep
Sleep
Stacking
Reject the bill
Wake up
Wake up
Wake up
Bill input
Bill input
giving credit Idle few secs
Open
Open
Open
- 6 -
S6 Pin-out Assignments (Service Pulse for 12V DC)
1 2 3 4 5 6 7 8 9 10
2519
11
2620
12
2721
13
282216
14
292317
15
302418
For the 12V DC version of the S6 bill validator, the harness(WEL-V707) has
a dual-in-line 30-pin peripheral connector at one end and a 9-pin mating
connector at the other end. Connect the 30-pin connector to the side of the
bill validator and the 9-pin mating connector to the 12V DC power
cable(WEL-V708).
9-pin mating connector pin-out assignments:
Pin 1 INHIBIT + Pin 6 Reserved
Pin 2 INHIBIT - Pin 7 CREDIT
Pin 3 SERVICE + Pin 8 Reserved
Pin 4 SERVICE - Pin 9 GND
(Power Return )
Pin 5 +12V DC
(Power In)
Dual-in-line 30-pin peripheral connector pin-out assignments:
Cable Order No. : WEL-V707(3-BA-A7V7-71)
12 3
65
4
789
CAUTION: Turn off the power before connecting or disconnecting the
bill validator.
Pin 16 - Reserved
Pin 17 - Reserved
Pin 18 - INHIBIT -
Pin 19 - Reserved
Pin 20 - GND (Power Return)
Pin 21 - KEY
Pin 22 - CREDIT
Pin 23 - Reserved
Pin 24 - Reserved
Pin 25 - Reserved
Pin 26 - Reserved
Pin 27 - Reserved
Pin 28 - Reserved
Pin 29 - Reserved
Pin 30 - Reserved
Pin 1 -
Pin 2 -
Pin 3 - +12V DC(Power In)
Pin 4 - INHIBIT +
Pin 5 - KEY
Pin 6 - Reserved
Pin 7 - Reserved
Pin 8 - Reserved
Pin 9 - Reserved
Pin 10 - GND
Pin 11 - Reserved
Pin 12 - Reserved
Pin 13 - Reserved
Pin 14 - Reserved
Pin 15 - Reserved
SERVICE -
SERVICE +
*
When S6 takes the bill, it sends a signal through 〝Wake_up〞pin as
below:
S6 Wake_up Signal
Normal
Wake up DC 0~1 V
DC+ 5~12 V
100 ms

- 8 -
1. Condition 1 : When B.A. wakes up and does not take any bill.
2. Condition 2 : When B.A. takes a true bill.
3. Condition 3 : When B.A. rejects a fake note.
S6 Service Signal for ICA Only (It works like a switch)
Close
Close
Close
Sleep
Sleep
Sleep
Stacking
Reject the bill
Wake up
Wake up
Wake up
Bill input
Bill input
giving credit Idle few secs
Open
Open
Open
- 9 -
Cable

- 10 -