ICT Hybrid Power ICT-IPS-DC12-BMM User manual

Hybrid Power Series
INSTRUCTION MANUAL
855-350-000
Innovative Circuit
Technology Ltd.
Models:
ICT-IPS-DC12-BMM
ICT-IPS-DC12-BMMP
ICT-IPS-DC12-BMMD
ICT-IPS-DC12-BMMDP
ICT-IPS-DC24-BMM
ICT-IPS-DC24-BMMP
ICT-IPS-DC24-BMMD
ICT-IPS-DC24-BMMDP

2 Innovative Circuit Technology Ltd.
WARNING
Risk of serious personal injury or damage to equipment and property! Always observe the
following:
•Install and operate unit in a restricted access location. A restricted access area is an area to
which access can be gained only by service personnel through the use of a special tool, lock
and key, or other means of security and which is controlled by the authority responsible for
the location
•Install unit in locations where children are likely not to be present.
•Install Earth connection to the unit before connecting AC input due to high leakage current.
•Use caution when handling unit under load as surface can reach hot temperature.
•Operate the supply from a grounded 3 wire 120Vac or 230/240Vac source (50 or 60Hz) with a
branch circuit breaker rated 30A or less.
•The DC-DC converter module is NOT hot pluggable. Do not open unit. Module maybe service
only by qualified personnel due to hazardous voltage inside.
Always observe the following for applications requiring a backup battery:
•Use only a Lead-Acid or Lithium-Ion battery with rating and capacity appropriate for the model
of supply in use
•If a Lithium-Ion battery is used, it must have an integrated battery management system (BMS)
to protect the battery cells from inappropriate voltage or current levels
•Use an appropriate DC over-current protection device in line with the back-up battery
connection
•Use a disconnect switch or circuit breaker in series with the battery connection, to ensure
installation and service is done with the battery de-energised
•Use wire and connectors rated for the maximum load current
•Ensure battery polarity is correct before connecting
•Do not attempt to charge a frozen battery
•Handle batteries with care, never short circuit battery terminals
•Always install batteries in a well-ventilated area
•Always consult with battery manufacturer and observe all battery manufacturer
recommendations.
CAUTION
Risk of personal injury or damage to equipment! Always observe the following:
•Install in a protected environment, keep sources of moisture away from unit
•Ensure the total power consumption of the load does not exceed the continuous rated
capacity of the power supply output or the DC-DC converter output and input
•Do not block air inlet or outlet openings in the unit
•Do not place the power supply directly above or below an exposed battery, due to possible
presence of corrosive and/or flammable gasses
Rev 0 (2023)
Hardware version: 04
Copyright © 2023 Innovative Circuit Technology Ltd. All rights reserved. No part of this
publication may be reproduced, stored in a retrieval system or transmitted in any form or by
any means, electronic, mechanical, photocopying, recording or otherwise, without the prior
written consent of Innovative Circuit Technology Ltd.

Innovative Circuit Technology Ltd. 3
Contents
INTRODUCTION ........................................................................................4
INSTALLATION ..........................................................................................4
Check Unit ..................................................................................................5
Configure a System ....................................................................................5
Install Unit ...................................................................................................8
Parallel Shelf Installation ......................................................................... 14
OPERATION (Front Panel)...................................................................... 16
System Status.......................................................................................... 17
Battery Management Module................................................................... 18
DC-DC Converter Module........................................................................ 21
Alarm Inputs............................................................................................. 21
Alarm History ........................................................................................... 22
Network Status and Advanced Options................................................... 23
Password Reset (Front panel)................................................................. 24
OPERATION (No ICM) ............................................................................ 24
OPERATION (Network GUI).................................................................... 24
Log In to the Unit...................................................................................... 24
System..................................................................................................... 25
Power Modules........................................................................................ 26
Battery Backup (with optional Battery Management Module).................. 28
DC-DC Converter .................................................................................... 34
Alarms...................................................................................................... 35
Communications ...................................................................................... 36
Router Configuration................................................................................ 45
Text Message Notifications...................................................................... 47
Troubleshooting Network Communications............................................. 47
STATUS INDICATORS AND ALARMS................................................... 49
PRODUCT SPECIFICATIONS................................................................ 52
LIMITED WARRANTY............................................................................. 56

4 Innovative Circuit Technology Ltd.
INTRODUCTION
The Hybrid Power Series is a complete and flexible 1RU DC power system with
intelligent networked monitoring and control, advanced battery management,
and 12 V or 24 V integrated DC output converter option in a 19”chassis. The
power shelf can accommodate a factory-installed Intelligent Control Module
(ICM) with front graphic display and up to three hot-swappable 700 W or 1500
W 24 or 48 V primary DC output power modules. One slot will be configured
with a factory-installed Battery Management Module (BMM) with low voltage
disconnect (LVD) contactor, with one or two 100 A circuit breakers.
Primary DC output power module specifications:
Power Module
24V 25A
ICT700-
24PM
48V 12A
ICT700-
48PM
24V 54A
ICT1500-
24PM
48V 27A
ICT1500-
48PM
Output Voltage
adjustment range (V)
23.0 –31.0
46.0 –62.0
23.0 –31.0
46.0 –62.0
Default Output
Voltage (V)
27.6
55.2
27.6
55.2
Output Current Limit
adjustment range (A)
5 –25
2.5 –12.5
5 –54
3 –27
Default Current Limit
(A) (+5%, -0%)
25
12.5
54
27
A typical configuration is illustrated below. This unit consists of a power shelf
with an Intelligent networked Control Module (ICM), two primary DC output
power modules, a dual input Battery Management Module (BMMD), and an
integrated DC Output Converter module. This single 1RU hybrid power system
provides up to 3000 watts of DC power with built-in Ethernet, LVD, advanced
battery management, and a DC converter providing up to 700 watts of 12 or +/-
24 VDC output.
Figure 1: Typical Hybrid Power Series Configuration
ICM
BMMD
DC Output Converter

Innovative Circuit Technology Ltd. 5
INSTALLATION
Check Unit
Perform a physical check of the unit as it is being taken out of the box to ensure
it has not been damaged during shipping. Check that the system configuration
matches the version ordered, and that the following accessories were shipped
with your unit:
•Instruction Manual
•Removable 3 pin AC input wire clamp connector plug (in bag)
•Removable 7 pin alarm and temp sensor wire clamp connector (in bag)
•Removable 3 pin Form-C alarm relay connector (in bag)
•Plastic u-shaped cover with four 6-32x1/4” screws for output bus bars
(in bag)
•Two rack mounting ears (installed)
•Two bolt/washer/nut sets for connections to the output bus bars (in
bag)
•Two bolt/washer/nut sets for connections to the Battery Management
Module bus bars (in bag)
•Remote battery temperature sensor (ICT-TMP) included when a BMM
is installed in the shelf
Configure a System
A complete Hybrid Power Series system will consist of at least one power shelf
with the Intelligent Control Module (ICM), one to two matching 700W or 1500W
Primary DC output power modules, one integrated DC output converter and
Battery Management Module (BMM). A secondary shelf may also be used to add
up to an additional four modules to a system, two of which may utilize a Load
Distribution Module (LDM). The ICM, BMM, and LDM are factory-installed
options, but the primary DC power modules are hot-swappable and can be used
in any of the remaining slot locations in a power shelf.
Standard Hybrid Power Series Versions:

6 Innovative Circuit Technology Ltd.
Description
Model No.
(negative V output)
Model No.
(positive V output)
Intelligent Power Shelf with
integrated Ethernet controller.
Factory-installed 100 A Battery
Management Module with
LVD and 700 W 12 V
integrated DC converter
output.
ICT-IPS-DC12-BMM
ICT-IPS-DC12-BMMP1
Intelligent Power Shelf with
integrated Ethernet Controller.
Factory-installed 200A Battery
Management Module with
LVD and 700 W 12V integrated
DC converter output.
ICT-IPS-DC12-BMMD
ICT-IPS-DC12-BMMDP1
Intelligent Power Shelf with
integrated Ethernet Controller.
Factory-installed 100A Battery
Management Module with
LVD and 700W 24W integrated
DC converter output.
ICT-IPS-DC24-BMM
ICT-IPS-DC24-BMMP1
Intelligent Power Shelf with
integrated Ethernet Controller.
Factory-installed 200A Battery
Management Module with
LVD and 700W 24V integrated
DC converter output.
ICT-IPS-DC24-BMMD
ICT-IPS-DC24-BMMDP1
Contact ICT for other possible Hybrid Power Series configurations
Primary DC Output Power Module Models
Description
Model No.
24V 700W primary DC output power module (27.6V, 25A)
ICT700-24PM
48V 700W primary DC output power module (55.2V, 12.5A)
ICT700-48PM
24V 1500W primary DC output power module (27.6V, 54A @ 230Vac)
ICT1500-24PM
48V 1500W primary DC output power module (55.2V, 27A @ 230Vac)
ICT1500-48PM
1
Suffix “P” denotes shelf configured for positive battery voltage. Blank denotes negative battery
voltage (i.e., for use with a -48 V system)

Innovative Circuit Technology Ltd. 7
Available Accessories:
Description
Model No.
Blanking plate for unused power shelf
positions (snap-in)
ICT-BPM
Remote battery temperature sensor (1pc
included with power shelf/BMM)
ICT-TMP
Secondary power shelf parallel output bus
bar jumper strap (for two power shelves)
ICT-PAR
Secondary power shelf parallel RJ11 control
cable jumper (4”)
ICT-JMP
Set Up the 1 RU Hybrid Power Shelf:
Ensure you have the correct power shelf, with the BMM factory configured for
positive or negative battery voltage (See shelf model numbers above). Check that
you have the correct number of matching power modules for your application.
•Install one to three matching hot-swappable power modules - with the
same voltage and power rating - in any remaining open shelf positions.
The primary DC output power modules will share the total output load,
automatically disconnecting from the internal power bus in the event of
an internal failure, and may be “hot-swapped” (you can insert or remove
a module while the shelf is powered) If you need “N+1” redundancy,
ensure the combined power rating of all the installed primary DC output
power modules exceeds the total requirement of the planned load by at
least 700 W (for 700 W power module) or 1500 W (for 1500 W power
module). (N+1 operation requires excess power module capacity to
ensure that the load can be fully powered, even if one power module
should fail or be removed)
•Carefully align each power module with the internal shelf guides. Firmly
push the module into the connectors in the slot. When the latch clicks
and the module is flush with the front plate, it is fully installed (see Figure
2). Note that Power Modules can be easily removed by pressing the
release latch located under the module handle to the right while firmly
pulling the module from the Power Shelf.
[NOTE] (The shelf may be left powered on while swapping modules)
•Snap (do we want “snap” or “install”) in a shelf blanking plate (ICT-BPM)
into any unused shelf positions to prevent accidental access to the
internal circuitry of the shelf.

8 Innovative Circuit Technology Ltd.
Figure 2: Installing Power Module in a Hybrid Power Shelf
Install Unit
WARNING
Risk of serious personal injury or damage to equipment and property! Always
observe the following!
•When using a backup battery ensure the nominal battery voltage is correct
for the model of power modules installed, and that the battery positive is
connected to the positive (+) terminal and the battery negative is
connected to the (-) terminal. Note that the BAT terminal on the BMM
may be internally tied to the (+) or (-) shelf output through the LVD
contactor, depending on the polarity of the power shelf used (see the
application note of DN-113v3, “Understanding -Polarity”)
•Use an appropriate DC over-current protection device such as a fuse or
circuit breaker in-line with and near to the battery connection
•Do not tie either power shelf main output to the BAT terminal on the BMM,
as this may short circuit the battery or bypass the internal LVD circuitry in
the BMM
•Make any earth ground connection to only a single LOAD or BAT terminal if
required. Do not ground both the load and battery as this may bypass the
internal LVD circuitry
•AC input wiring to the Hybrid Power Series unit must be protected using an
outlet with a branch rated circuit breaker of 30 A or lower value
Module Latch

Innovative Circuit Technology Ltd. 9
Check that the system Output Voltage and Current Limit match the requirements
of the battery and the loads to be connected (see the section of “System Status”
for details on setting your voltage and current limits).
Figure 3: Typical Rear View (Showing BMM, DC Output Connectors)
Mount the unit in an enclosed standard 19”equipment rack or other restricted
access location, using rack mounting screws (not supplied). Support the rear of
the unit with rack shelf supports or back rail if desired.
Make connections to the load using wire and connectors appropriately rated for
the maximum output current capability of the unit. The load may be powered two
different ways:
Load Connection Point
Features
Directly from main shelf DC output bus
bars
Full current rating of the shelf is
available to operate the load, limited
only by the maximum output capability
of the combined power modules
Integrated DC Output converter bus
bars
Fully isolated, 12 V or 24 V, 700 W
maximum
•The integrated DC output converter output has POS and NEG terminals.
Ensure polarity is correct when connecting the load.
•Connect a ground bonding wire from the chassis ground stud to the rack.
See the following Hybrid Power Series block diagram for internal details on
connection options.
[NOTE] Note that a NEGATIVE BATTERY voltage (typically -48V) system shelf is
shown. A POSITIVE BATTERY voltage (+12V or +24V) system power shelf will
have the BMM and internal back plane power connection made to the DC+bus.
BMMD
Integrated DC
Output
Converter
Main Shelf
DC Output
Main Shelf
AC Input
Alarm
Output
Remote
Inputs
Network
Input

10 Innovative Circuit Technology Ltd.
Figure 4: Battery Backed Hybrid Power Shelf –Internal Block Diagram (NEG. V Output)
Make Sensor and Alarm Connections
•Connect the Form-C alarm contact monitoring wiring to the ALARM Output
connector if needed, as shown in the following table. On a dual-shelf
system the primary shelf contacts are flagged for all system alarms while
the secondary shelf contacts indicate secondary power module faults only.
Pin Number
Name
Function
1
NC
Alarm NC (alarm state)
2
NO
Alarm NO (alarm state)
3
Common
Alarm output common
Alarm Output Connector: (use 22-26 AWG wire)
•Connect the external Battery Temperature Sensor (ICT-TMP, included with a
BMM equipped shelf, for use with lead-acid batteries only) to the REMOTE
input plug on the back panel (see Remote input table, below), to
compensate the shelf output voltage according to the battery temperature.
Mount the sensor to the mid-level side of the middle battery in a battery

Innovative Circuit Technology Ltd. 11
string using the adhesive backed clip, as shown in Figure 5. The rate of
voltage compensation can be adjusted via the ICM front panel interface, or
the WEB GUI in the Battery Backup Settings & Control tab. The default
compensation is 0mV/C per cell (no compensation adjusts this according to
the battery manufacturer’s recommendation to enable charge voltage
temperature compensation. Battery temperature is assumed to be 25° C if
no sensor is installed.
Figure 5: Battery Temperature Sensor Installation
•Install wiring to monitor up to four external voltage free alarm contacts,
typically for external sensors such as a door or window switch, smoke
detector output, or water detector etc. Enable the alarm inputs and set the
contact logic (normally open or contact normally closed) in the WEB GUI,
Alarms Settings & Control tab.
Pin Number
Name
Function
1
Alarm 1
Remote alarm 1 input
2
Alarm 2
Remote alarm 2 input
3
Alarm 3
Remote alarm 3 input
4
Alarm 4
Remote alarm 4 input
5
Alarm Return
Common remote alarm return point
6
Bat Temp
Remote Battery Temperature sensor
7
Bat Temp
Battery temp sensor return
Remote Input Connector: (use 22-26 AWG wire)
Make Battery Connections to BMM
The BMM provides a convenient and safe way to connect an external lead-acid
or lithium-ion back-up battery to the Hybrid Power Series. A 100 A high current
hydraulic-magnetic circuit breaker provides over current protection, while an
internal LVD contactor will disconnect the battery should it discharge below a
safe level. Internal battery current monitoring provides a full suite of remote
battery charge monitoring features.

12 Innovative Circuit Technology Ltd.
WARNING
Risk of serious personal injury or damage to equipment and property! Always
observe the following!
•When connecting a battery ensure the nominal battery voltage is correct
for the model of power modules installed, and that the battery positive is
connected to the positive (+) terminal and the battery negative is
connected to the (-) terminal. Note that the BAT terminal on the BMM may
be internally tied to the (+) or (-) shelf output through the LVD contactor,
depending on the polarity of the power shelf used. Check shelf model
polarity before connecting a battery to the BMM! (see the application
note of DN-113v3, “Understanding -Polarity”)
•Only use the Equalize Charge setting for flooded lead-acid batteries in a
well-ventilated location. Do not use Equalize Charge on sealed batteries!
Always consult with battery manufacturer and observe all battery
manufacturer recommendations.
•If a lithium-ion battery is used, it must utilize an integrated battery
management system (BMS) to protect the battery cells from inappropriate
voltage or current levels.
•Do not tie either of the power shelf main outputs to the BAT terminal on
the BMM, as this may short circuit the battery or will bypass the internal
LVD circuitry in the BMM.
•Make any earth ground connection to only a single LOAD or BAT terminal if
required. Do not ground both the load and battery as this may bypass the
internal LVD circuitry.
•Use wire and connectors appropriately rated for the highest possible
system current when making connections to the battery, BMM, and power
shelf
Note: Check that the default system output voltage and current limit match the
requirements of the battery and the loads to be connected. Adjust the system
Output Voltage and Current Limit (see System Settings & Control tab) to match
the combined battery and system load requirements before making final
connections, if required. Use only identically rated battery strings for the dual
battery BMMD option to ensure equal charging of each battery set.
Verify the polarity of the BMM installed in your power shelf by noting the label
under the rear BMM BAT bus bar input. (“BAT +” indicates a positive battery
voltage system with the LVD contactor and battery breaker internally
connecting this terminal to the shelf “POS”output, while “BAT –“indicates a
negative battery voltage system, with the LVD contactor and battery breaker
internally connecting this terminal to the shelf “NEG“ output)

Innovative Circuit Technology Ltd. 13
Use wire and connectors appropriately rated for the highest possible system
current when making connections to the battery, BMM, and power shelf.
Connect the battery hot lead (see comment on polarity, above) to the BMM BAT
bus bar, and the battery return lead to the main shelf output bus bar of the
corresponding polarity. (i.e.: a positive voltage system will have the battery (+)
tied to the BMM terminal, with the battery (-) tied to the main NEG output
busbar, a negative voltage system will have the battery (-) tied to the BMM
terminal, with the battery (+) tied to the main POS output busbar.
Figure 6: Negative voltage (positive ground)
Figure 7: Positive voltage (negative ground)

14 Innovative Circuit Technology Ltd.
Available BMM Variations:
-V BAT
+V BAT
Description
Connections
BMM
BMMP
Single 100 A battery circuit breaker
with LVD contactor with advanced
battery management capability
Single BAT input
bus bar (+ or –
polarity, see note
above)
BMMD
BMMDP
Dual 100 A battery breakers to
connect two identical battery
strings through an LVD and current
sensor with advanced battery
management capability for the
combined battery
BAT 1 and BAT 2
input bus bars
(both either + or –
polarity, see note
above)
Finalize all Shelf Wiring
Make a network connection: Connect a 10/100Base-T Ethernet cable to the
RJ45 LAN port on the back panel to allow for remote monitoring and control of
the power shelf.
(See the Network Monitoring and Control section for information on configuring
and using the built in Web-GUI, e-mail, or SNMP functions)
Check that all connections to the power shelf are correct and tight; install the
plastic bus bar cover(s) using the original screws provided.
Connect the AC power source: De-energise the AC source by switching off its
circuit breaker. Create a power cable using 3 conductor cord rated for the
maximum possible input current of the unit (up to 27 A for a 2800 W
configuration operating from a 120 VAC line) by stripping and terminating the
three wires in the Line, Neutral, and Ground terminals of the removable AC
input connector provided with the unit (AC line labeled “L”, neutral labeled “N”
and safety ground to the middle pin).
Plug the AC connector into the AC input on the power shelf back panel, and
tighten the captive retaining screws.
Wire the source end of the cord to the de-energised AC supply equipped with a
branch rated circuit breaker of 30A or less.
Optional Parallel Shelf Installation
Use a secondary power shelf for applications that require up to an additional
two or three power modules. The secondary shelf has no internal ICM, as it is

Innovative Circuit Technology Ltd. 15
controlled and monitored by the ICM on the primary unit, requiring only an
additional AC line input connection, a control jumper cable (ICT-JMP)
connection, and the installation of tie bars (ICT-PAR) to parallel the shelf
outputs. Do not attempt to connect shelves in series, they are meant for
parallel operation only!
The master and the secondary power shelf must be installed as a set into
adjacent rack locations to ensure the output power tie bars and control cable
jumper will correctly fit.
Figure 8: Primary and Secondary Shelf connected in Parallel
CAUTION
Risk of damage to equipment!
•Do not use the internal BMM battery LVD contactor for parallel applications
where load current can exceed the 150A maximum rating of the LVD
contactor
•Do not parallel BMM modules. A battery connection may be made to a
single BMM module, with maximum battery current not to exceed the
rating of the individual BMM unit (150A)
Install the Shelf Paralleling Bus Bars (ICT-PAR) and plastic bus bar covers as
shown in Figure 8, using the hardware included with the Hybrid Power Series.
Install the Parallel Control Cable (ICT-JMP) connecting the two RJ-11 style SHARE
ports as shown in Figure 8 to allow the Primary ICM to control the secondary
shelf. (Shelf slots 1 to 4 (front, L to R) are on the main shelf, slots 5 to 8 (front, L
to R) on the secondary shelf)
Connect alarm monitoring wiring to the Form-C contacts on the secondary shelf
if desired, to remotely monitor for secondary shelf module alarm conditions.
Connect a load to the parallel shelf outputs to utilize the combined power of all
power modules installed in the two shelves, or connect the loads to the back
panel output ports of any installed LDM modules for built in intelligent power
distribution.
Master
Unit
Slave
Unit
Parallel Control
Cable ICT-JMP
Tie Output Bars

16 Innovative Circuit Technology Ltd.
Connect a separate AC power cord to each shelf, using independent AC circuits
rated for the full power operation of each shelf.
OPERATION (Front Panel)
Switch on the external AC power source circuit breaker, and check that the
green POWER LED is lit on each power module, and that the ICM front graphic
display is lit.
Your Hybrid Power Series will start up and operate at the factory default
settings when AC power is connected, generally requiring no other set up or
adjustment for basic operation.
Use the web-GUI or the front graphic display on the ICM to monitor the unit
operation and to make changes to settings such as output voltage, current limit,
and battery low voltage disconnect points. (The display will go off after
approximately 60 minutes of no use, and can be re-activated by momentarily
pressing any of the front control buttons.)
Figure 9: ICM Front Control Interface –System Status Screen
The ICM Interface panel consists of the following elements:
System Display screen: Default System Status screen shown in Figure 9 displays
the shelf output voltage, the AC input voltage, and the total output current.
(Numerically, and with a graphical indication of relative magnitude of system
output current level) The screen will also show any active alarm conditions, and
the current reading will flash to indicate when the unit is operating at its current
limit.
Up/Down Buttons: Use to scroll through display screens, and to adjust
selected settings
Enter Button: Press to select a screen for adjustment, or to enter a new
value after adjustment
Back XButton: Press to return to the previous higher level menu item, or to
exit from a setting without making any change

Innovative Circuit Technology Ltd. 17
See the complete menu structure in the following diagram. Navigate through
the various screens using the up and down arrows, the back button, and the
Enter button.
Note that output voltage and current limit settings apply to the combined
output of all installed power modules. The ICM treats the combined modules as
a single high-power supply. Adjust the system output Voltage and Current Limit
(see System Settings section) to match the battery type and system load
requirements if required.
System Status
The main system status screen will show most current operating conditions for
the unit, primarily the Input Voltage (VAC), the Output Voltage (VDC), and the
total Output Current (A) (Flashing when at the set current limit). Other
information will be shown depending on the operating state of the unit:
•A small thermometer symbol to indicate that the remote temperature
sensor is installed and may be compensating the output voltage
•A bar graph indicating relative output current
•Indication that the output has been disabled (off)
•Indication that a battery discharge test is in process
System Settings: The Output Voltage and output Current Limit settings come
with factory default values that should be adjusted to match your actual system
and battery float voltage requirements, as shown below:
Scroll to highlight the parameter to change
•System Voltage
•Max total Output Current Limit
•Output Enable ON/OFF (default = ON)
•Advanced Options (Set screen Password,
Clear Password, Set screen Lockout
timer, Reset Comm settings to defaults)
Press Enter to select
Press Enter to move to the System Settings

18 Innovative Circuit Technology Ltd.
Once the Output Voltage and Current Limit values are configured to suit the
connected battery and loads, switch on the BMM battery breaker 1, and battery
breaker 2 (if installed) to connect the backup battery string(s) to the system.
Battery Management Module
The Battery Management Module (BMM) provides a convenient and safe way to
connect an external back-up battery (or 2 matching battery strings with the
BMMD) to the Hybrid Power Series. A 100 A high current hydraulic-magnetic
circuit breaker (two breakers on the BMMD) provides over current protection,
while an internal LVD contactor will disconnect the battery should it discharge
below a safe level. Internal battery current monitoring provides a full suite of
remote battery charge monitoring features.
The BMM Status Screen indicates the Battery Voltage (VDC), the combined
Battery Current (+ A for charging, -A for discharging), the approximate battery
State of Charge (SOC %), and a bar graph showing relative magnitude of the
total battery current. A battery graphic marked with Xindicates the battery is
disconnected, replacing the SOC reading, as shown below.
The SOC% is estimated by counting the ampere-hours (Ah) flowing into and out
of the battery while knowing the nominal rated capacity of the battery (See
BMM Settings Screen below to adjust the battery Ah capacity) The system
resets the SOC to 100% whenever it detects that the battery is at the rated Float
Voltage with minimal charge current for at least 24 hr.
Scroll to adjust parameter (Output V shown),
press Enter to set value. Press Back Xto
return to System Settings Screen
Alarms will be shown as they occur,
press Back Xbutton to return to the
Status screen, press Enter for
Alarm History info
BMM Status Screen
with Battery-
Disconnected icon

Innovative Circuit Technology Ltd. 19
BMM Settings (All Battery Types): The module comes with factory default
settings loaded that should be configured to match the actual battery used in
the system.
WARNING
Always consult battery manufacturer's specifications when selecting battery
type. Incorrect battery type setting may damage your battery.
If Lithium-Ion type battery is selected, it must utilize an integrated battery
management system (BMS) to protect the battery cells from inappropriate
voltage or current levels.
Configure the Battery Type of the battery used in the system (Lead-Acid or
Lithium-Ion). If Lithium-Ion type battery is selected, the following battery
parameters and settings will be unavailable: Battery State of Charge, Run-time
Remaining, Voltage Temperature Coefficient / cell, Equalize Charge, and Battery
Discharge Test; these should be available from the li-ion battery’s integrated
BMS.
Adjust the LVD contactor Disconnect and Reconnect Voltage according to the
battery manufacturer’s recommendations.
Set the Battery Charge Current Limit to limit the maximum battery charge
current provided, while still allowing the full rated current to be drawn from the
main output.
Set the Battery Overcurrent Alarm level (A) to trigger an Alarm for excessive
discharge current or charge current. (set to 0 A to disable this alarm)
Configure the combined Battery Capacity (Ahr) as well as the Battery Rate (hrs)
used in the battery specification to determine the battery capacity. (Usually, will
be 20 hr or 10 hr rate.) If a lead-acid battery is connected to the system, this
information is used to estimate the battery state of charge. Note that series
connected batteries have the Ahr capacity of a single battery, while connecting
batteries in parallel increases the total Ahr capacity.
BMM Settings (Lead-Acid Batteries only): The following additional settings
are only available if the system is configured for use with a lead-acid type
battery:
Set the Low SOC Alarm (%) if desired, to raise an alarm when the battery is
nearly discharged.

20 Innovative Circuit Technology Ltd.
Ensure the Battery Temperature Sensor (ICT-TMP) is installed and connected to
the battery case (see Make Sensor and Alarm Connections in the Installation
section) for optimal lead-acid battery charging and best battery life. Set the
Temperature Compensation/°C level per battery cell to match the
recommendation of the battery manufacturer. (-4 mV/°C per cell is typical)
Configure the Battery Equalize Charge voltage, duration, and automatic repeat
interval if desired when using flooded lead-acid type batteries only. The system
will step up the output voltage to the Equalize Voltage for the Equalize Duration
time whenever the Equalize Status is set to Enable.
WARNING
Use the Equalize Charge setting for flooded lead-acid batteries in a well-
ventilated location only. Do not use Equalize Charge on sealed batteries!
Configure the Battery Discharge Test to check on the battery’s ability to power
the system for a set duration. Set Max Discharge Time, minimum Stop Voltage,
and the automatic repeat Interval if desired. Each time the test is run the output
voltage from the power modules will be reduced so that the external battery
will power the system load until either the Max Discharge Time limit or the Stop
Voltage is hit. A Discharge Test Complete notification (on the front display and
with an e-mail if messaging is configured via the Network GUI) will indicate a
Test Failure if the Stop Voltage is hit before the Max Time limit, as the battery
was not able to power the load for the desired duration.
A Battery Discharge Test of a fully charged battery can be manually initiated by
changing the discharge test Status parameter to Enabled.
Optional BMM versions are available which have the status screens shown
below:
Dual Battery String BMMD Status Screen
•Battery 1 Voltage
•Battery 2 Voltage
•Combined Battery Current
•Combined SOC%
Press Enter to move from the Status screen
to the BMM Settings screen