ICW UL500 User manual

ICWUSA.com, Inc.
If you have any questions, please call 1-800-558-4435
ULTRA ARM INSTRUCTIONS
ULTRA ARM INSTRUCTIONS - rev 12/06/2012 mf
Locate the wall stud and mark the top
hole of the Wall Track, drill 11/64 pilot
hole and insert #14 screw and tighten
slightly. Use a level, mark the lower
holes, drill pilot holes and then insert the
#14 screws.
NOTE: #14 Wood screws are supplied with unit. If
installing into metal studs, you will need to replace
these with proper metal stud fasteners
MOUNT ULTRA TRACK TO WALL Remove
small socket
head cap
screw in the
top middle
of the Wall
Track.
Remove
plastic cover.
Insert Slider
into Wall Track
as shown
at left and
replace the
small socket
head cap
screw and
plastic cover.
ATTACH SLIDER TO ULTRA TRACK Once you have adjusted the
slider to the desired height,
tighten down the Track
Slider using the handle on
the slider as shown.
Once tight, make sure the
handle is positioned so that
it is pointing down as far
as possible. Pull and turn
handle to position.
ATTACH WALL PLATE TO WALL
Locate the stud and mark the top hole,
drill 11/64 pilot hole and insert #14
screw and tighten slightly. Using a
level, mark the lower hole and drill pilot
hole, insert #14 screw and, with the
unit level, tighten both screws.
NOTE: ICW supplies #14 wood screws. If
installing onto metal studs, you will need to
replace with proper metal stud fasteners.
W2
W3
ATTACH POLE CLAMP TO POLE
Using the 1/4” hex key,
separate the two halves
of the pole mount as
shown, place around pole
at the desired height and
reassemble.
IF MOUNTING TO A POLE
IF USING THE W2 OR W3
IF MOUNTING TO THE
ULTRA WALL TRACK
ATTACH RADIUS MOUNT TO POLE
Using a 1/8”
hex key wrench
make sure the
set screws in the
radius mount
are pulled out
enough that
the mount will
easily slide
down over the
pole. Tighten
the set screws.
IF YOUR
SYSTEM
DOESN’T
HAVE AN
EXTENSION
ARM
SEE “ATTACH
TO W2“
SECTION
ON PAGE 4

ICWUSA.com, Inc.
If you have any questions, please call 1-800-558-4435
ULTRA ARM INSTRUCTIONS
ULTRA ARM INSTRUCTIONS - rev 12/06/2012 mf
ATTACH VESA
Mount the VESA
plate to the
friction mount
using the 5/32” hex key and the
1/4-20 fl at head screws in the
hardware bag.
ATTACH TO MONITOR
Attach your
monitor to the
VESA plate
using the four
4mm screws in
the hardware bag.
ADJUST TILT HANDLES
Use the
handles to
adjust the tilt
of the monitor.
IF USING UL500
IF USING UL510
ADJUST TILT & MONITOR HEIGHT
Use the handles
to adjust the tilt of
the monitor.
Adjust the height of
the monitor along
the rails of the 510.
Then tighten in place
using slider knob. Slider Knob
ATTACH VESA
Mount the VESA
plate to the
friction mount
using the 5/32”
hex key and the
1/4-20 fl at head
screws in the
hardware bag.
ATTACH TO MONITOR
Attach your monitor to
the VESA plate user the
four 4mm screws in the
hardware bag.
IF MOUNTING TO A DESK
ATTACH DESKMOUNT TO DESK
Drill a 3/8 hole through the
horizontal surface you intend to
mount to and push the 3/8 stud
on the desk mount through the
hole. Slip the large mounting
washer over the stud from
underneath, add the 3/8 split-
washer, and secure in place
with the 3/8 nylock. Screw stud into desk mount
Desk Desk
Washer Nylock

ICWUSA.com, Inc.
If you have any questions, please call 1-800-558-4435
ULTRA ARM INSTRUCTIONS
ULTRA ARM INSTRUCTIONS - rev 12/06/2012 mf
ADJUST BALL VESA
TENSION & HEIGHT
Use the slider knob
to loosen the slider to
adjust the height of the
monitor on the Paralink.
Adjust the pivot tension
of the ball by gently
and evenly tightening
or loosening the four
screws on the back of
the ball VESA.
Slider Knob
Pivot tension
adjustment
screws
ATTACH VESA
TO MONITOR
Using a phillips
screw driver,
attach the VESA
plate to the back
of your LCD
monitor.
IF USING UL550
ADJUST
PARALINK TILT
Adjust Monitor to desired
position with ball VESA.
Tilt your monitor 50°
in any direction. Adjust
your monitor between
portrait and landscape
by rotating ball VESA.
Adjust monitor depth
by moving the paralink
forward or back then
tighting the depth
adjustment knob.
Depth
Adjustment
Knob
ATTACH PARALINK TO ULTRA ARM
Attach to Paralink to Ultra arm
using 3/8 bolt assembly and
1” bearing assembly provided.
Insert bolt assembly up through
arm. Place 1” bearing assembly
over bolt on other side of arm.
Place Paralink over bolt and
bearing and turn bolt until
Paralink is secure and smoothly
turns against the bearing.
1” bearing
assembly
3/8 bolt
assembly
Beauty
cap
Paralink
Ultra arm
ATTACH FLIPUP TO ARM
Attach the tray
fl ip-up assembly
to the arm bracket
using the provided
fl at head screws
and hex key.
ATTACH PARALINK KEYBOARD TRAY
Loosen knob to adjust Paralink.
Adjust horizontally for keyboard tray
and vertically for monitor. Tighten
knobs when in desired position.
Attach the keyboard tray
to the Keyboard Mount
using the supplied 5/16-
18 socket head screw.
IF USING PARALINK KEYBOARD TRAY IF USING ULTRA KEYBOARD TRAY

ICWUSA.com, Inc.
If you have any questions, please call 1-800-558-4435
ULTRA ARM INSTRUCTIONS
ULTRA ARM INSTRUCTIONS - rev 12/06/2012 mf
ULTRA WIRE
MANAGEMENT
[1] Prepare all
cables to route
within the arm by
placing them
near cavity of arm
and bundling together if necessary. Remove
cover by unscrewing two socket head cap
screws. Screws are captured by the cover
so they cannot fall out. Once screws are
disengaged, pull cover out of arm.
1 2 3
[2] Place cables over
cover and within the
channels. Do not block
the hole where screws
will engage in arm.
[3] Replace cover and
tighten screws. Cables
should be able to pull
through to desired
position if necessary.
ATTACH UL500 TO W2
Attach to UL500 to W2 wall
mount using 3/8 bolt assembly
and 1” bearing assembly
provided. Insert bolt assembly up
through wall ear. Place 1” bearing
assembly over bolt on other side
of wall ear. Place UL500 over bolt
and bearing and turn bolt until
UL500 is secure and smoothly
turns against the bearing. Beauty
cap
UL500
W2
1” ID bearing
assembly
3/8 bolt
assembly with
3/8 ID bearing
ATTACH PARALINK TO W2
Attach to Paralink to W2 wall
mount using 3/8 bolt assembly
and 1” bearing assembly
provided. Insert bolt assembly
up through wall ear. Place 1”
bearing assembly over bolt on
other side of wall ear. Place
Paralink over bolt and bearing
and turn bolt until Paralink is
secure and smoothly turns
against the bearing. Beauty
cap
Paralink
W2
1” ID bearing
assembly
3/8 bolt
assembly with
3/8 ID bearing
ATTACH UL510 TO W2
Attach to UL510 to W2 wall
mount using 3/8 bolt assembly
and 1” bearing assembly
provided. Insert bolt assembly
up through wall ear. Place 1”
bearing assembly over bolt on
other side of wall ear. Place
UL510 over bolt and bearing
and turn bolt until UL510 is
secure and smoothly turns
against the bearing.
1” ID bearing
assembly
3/8 bolt
assembly with
3/8 ID bearing
Beauty
cap
UL510
W2