ICW ULTRA 180 User manual

Page 1
If you have any questions, please call 1-800-558-4435
ULTRA 180 ARM INSTALLATION - rev 04/09/14 pjm
ULTRA 180 ARM INSTALLATION
Page 1 of 4
Locate the wall stud and mark the top
hole of the Wall Track, drill 11/64 pilot
hole and insert #14 screw and tighten
slightly. Use a level, mark the lower
holes, drill pilot holes and then insert the
#14 screws.
NOTE: #14 Wood screws are supplied with unit. If
installing into metal studs, you will need to replace
these with proper metal stud fasteners
MOUNT ULTRA TRACK TO WALL Remove
small socket
head cap
screw in the
top middle
of the Wall
Track.
Remove
plastic cover.
Insert Slider
into Wall Track
as shown
at left and
replace the
small socket
head cap
screw and
plastic cover.
ATTACH SLIDER TO ULTRA TRACK Once you have adjusted the
slider to the desired height,
tighten down the Track
Slider using the handle on
the slider as shown.
Once tight, make sure the
handle is positioned so that
it is pointing down as far
as possible. Pull and turn
handle to position.
IF MOUNTING TO THE ULTRA WALL TRACK
b
a
IF MOUNTING TO A DESK
ATTACH DESKMOUNT TO DESK
Drill a 3/8 hole through the
horizontal surface you intend to
mount to and push the 3/8 stud
on the desk mount through the
hole. Slip the large mounting
washer over the stud from
underneath, add the 3/8 split-
washer, and secure in place
with the 3/8 nylock. Screw stud into desk mount
Desk Desk
Washer Nylock

ULTRA 180 ARM INSTALLATION - rev 04/09/14 pjmPage 2 of 4
ATTACH WALL PLATE TO WALL
Locate the stud and mark the top hole,
drill 11/64 pilot hole and insert #14
screw and tighten slightly. Using a
level, mark the lower hole and drill pilot
hole, insert #14 screw and, with the
unit level, tighten both screws.
NOTE: ICW supplies #14 wood screws. If
installing onto metal studs, you will need to
replace with proper metal stud fasteners.
W2
W3
IF MOUNTING TO A WALL
IF MOUNTING TO A POLE
IF USING EV65
ATTACH VESA TO MONITOR
Attach the
monitor mount
assembly to
the back of
your monitor,
using the
4mm screws
provided.
ATTACH VESA TO EV65 JOINT
Socket
cap screw
VESA
plate
Insert stubs on VESA plate into
holes in the Ergovision joint
assembly. Insert 5/16 x 3/4
socket cap screws provided in
both sides and tighten. Use the
handle under mount
to loosen tilt friction
and adjust monitor
tilt.
ULTRA 180 ARM INSTALLATION
ATTACH POLE CLAMP TO POLE
Using the 1/4” hex key,
separate the two halves of
pole mount as shown, place
around pole at the desired
height and reassemble.

ULTRA 180 ARM INSTALLATION - rev 04/09/14 pjm
Page 3 of 4
IF USING EV710
ULTRA 180 ARM INSTALLATION
IF ATTACHING TO ULTRA FLIP-UP
ATTACH FLIP UP
1.Remove screws from
drop extension using
5/32” hex key.
2.Align holes in keyboard
tray with screw holes in
drop extension.
3.Attach keyboard tray
using the provided
screws.
IF ATTACHING TO QUICK DISCONNNECT
ATTACH QUICK DISCONNECT
1.Remove beauty cap on quick
disconnect block.
2.Remove screw using 3/16”
hex key.
3.Slide keyboard tray into quick
disconnect block.
4.Replace screw and tighten.
5.Replace beauty cap.
Beauty cap
Screw
ATTACH BALL VESA
Mount the VESA
assembly to the
slide rails. Screw
the slider knob
through the
rails and into the
VESA assembly
as shown.
ATTACH VESA TO MONITOR
Attach VESA to
monitor using four
4mm screws in the
hardware bag.
ADJUST BALL VESA HEIGHT & TENSION
1.To adjust the height of monitor,
loosen slider knob, set monitor
height on slider rails, then
tighten knob.
2.To adjust pivot tension, gently
and evenly tighten or loosen
the four screws on the back
of the ball VESA. Pivot tension
adjustment screws
Slider
knob

ULTRA 180 ARM INSTALLATION - rev 04/09/14 pjm
ULTRA 180 ARM INSTALLATION
Page 4 of 4
ULTRA 180 ARM CABLE MANAGEMENT
RUN CABLES THROUGH UL180 ARM
1.Cover plate is spring loaded. Loosen cover plate screws
on side of arm just enough to t cables through gap.
2.Run cables loosely between cover plate and arm.
Cables can be run on either or both sides of the arm.
3.Push cover plate against arm and
tighten screws, being careful
not to pinch cables.
STORE CABLE INSIDE COVER PLATE
Extra cable can be looped inside the cover plate to provide
a neater appearance and simplify cleaning.
ULTRA CORD MANAGEMENT
1.Prepare all cables to route within the arm by placing them
near cavity of arm and bundling together if necessary.
2.Remove cover by unscrewing four socket head cap screws.
Screws are captured by the cover so they cannot fall out.
Once screws are disengaged, pull cover out of arm.
3.Place cables within the channel. Do not block the holes
where screws will engage in arm.
4.Replace cover and tighten screws. Cables should be able to
pull through to desired position if necessary.
ADJUSTING ARM TENSION ADJUST UL180 ARM TENSION
Using the 3/16” T-handle
hex wrench provided, turn
the screw in the UL180
arm clockwise to lighten
the arm’s load resistance,
or counter-clockwise
to increase the load
resistance.
IMPORTANT
Extend the UL180 straight out and
be sure all equipment is mounted
on the arm before adjusting
he arm’s resistance. Use the
T-handle provided to adjust the
arms’ resistance. Do not use
power tools to adjust.