ICW ELITE 5220 User manual

ELITE 5220 & 5216 INSTALLATION
EASY-TO-CABLE-MANAGE ELITE 5220 & 5216 INSTALLATION - 11/13/17Page 1 of 3
If Mounting To Wall or Wall Track
DO NOT use power tools to assemble or
adjust the arm. Use hand tools ONLY.
IMPORTANT
ICW recommends wood or metal stud mounting only.
MAXIMUM LOAD CAPACITY:
28 LBS (12.7 KG)
MOUNT TO WALL
• Locate stud and mark top hole.
• Drill 11/64 pilot hole and insert
#14 screw and tighten slightly.
• Using a level, mark lower
holes and drill pilot holes.
• Insert #14 screws and, with
unit level, tighten all screws.
ICW supplies #14 wood screws.
If installing onto metal studs,
you will need to replace with
proper metal stud fasteners.
To tighten center screw,
additional tools may be helpful
(not provided). Provided screws
will accept a 90° bent Phillips or
square bit nut driver on a short socket wrench.
Attach wall track to
wall using installation
instructions provided
with track.
Attach track adapters
Attach track adapters
to back of wall ear by
threading socket head
screws from front of wall ear into track
adapters. Loosely tighten with 5/32” hex key.
Attach wall plate to track
Slide track adapters into track from either top or
bottom. Position wall ear to desired location on track.
Firmly tighten wall ear screws with 5/32” hex key.
CAUTION!
If Mounting To A Desk
ATTACH TO DESK
If Mounting To A Pole
ATTACH TO POLE
MOUNT TO WALL TRACK
Drill a 3/8 hole through the
horizontal mounting surface.
Screw the 3/8 all-thread
stud into offset hole in desk
mount. The stud is found in
the hardware bag.
Push the 3/8 stud on desk
mount through the hole the
desk. Slide large mounting
washer over the stud from
underneath and secure in
place with the 3/8 nylock nut.
Run cables through center of
desk puck.
•Do not attempt to adjust the Elite arm until all
components are mounted (monitor, keyboard, etc.)
•Arm must be completely horizontal (extended)
before adjusting the arm’s tension. Failure to do so will
damage the arm and void the warranty.
•NEVER loosen or remove
any of the 16 shoulder bolts.
Doing so will cause the arm to
immediately come apart with
tremendous force, and could
cause serious injury.
• If equipment requiring AC power
is mounted to this unit, have a
certiedelectricianinspecttheinstallation.
• Failure to install this unit according to these
instructions will void all ICW warranties. If installed
incorrectly, ICW is not liable for any damage or injury
caused by the unit.
The Elite arm contains high pressure gas
springs. The following cautions MUST be
observed to avoid serious injury.
Washer
Nylock nut
Desk surface
All-thread stud
Cables run
through center of
desk puck and out
through slot
8 shoulder bolts
on each side
Separate the two sections
of the pole mount. Place around pole,
reassembleandrmlytightenscrews.

ELITE 5220 & 5216 INSTALLATION
EASY-TO-CABLE-MANAGE ELITE 5220 & 5216 INSTALLATION - 11/13/17Page 2 of 3
ATTACH PARALINK KEYBOARD TRAY
• Remove beauty cap on
Paralink.
• Remove screw using 3/16”
hex key.
• Slide keyboard tray into
Paralink.
• Replace screw and tighten.
• Replace beauty cap.
• Loosen knob, adjust Paralink
to desired position, then
tighten knob.
Beauty cap
Screw
Adjustment
Knob
Extend the arm straight out and
lay all the cables for monitor,
keyboard and mouse in the
channel on top of the arms. Lay cables evenly around
adjuster with wire loom on
each side.
Wire tie cables around adjuster,
securing the cords and the wire
loom. Leave some slack.
Add provided wire clips, weaving
through wire loom to secure cables.
NOTE: YOU MUST LEAVE SOME
SLACK IN THE CABLES TO
ALLOW FOR ARM MOVEMENT. Add wire clip to end of arm.
Run cables through opening in
center of wall ear.
12
34
MANAGE CABLES THROUGH ARM
ATTACH FLIP-UP TO DROP
Attachthetrayip-up
assembly to the drop
usingtheprovidedat
head screws and
hex key.
ATTACH VESA
Attach VESA to monitor using four
4mm screws in the hardware bag.
Mount the VESA assembly by
screwing the knob through the rail
into the VESA.
REMOVE ARM COVERS
END COVERS:
Remove the end
covers by unscrewing
the two 3/4” long
10-24atheadscrews
using a Phillips head
screwdriver.
CENTER COVER:
Remove the center
cover by unscrewing
the four 3/4” long
10-24atheadscrews
using a Phillips head
screwdriver.
TOP COVERS:
Remove the long
arm covers by
unscrewing the
two 1/4” long 6-32
atheadscrews
in the center of
the cover using
a Phillips head
screwdriver.
TORQUE 120 INCH POUNDS. DO NOT LOOSEN.

ELITE 5220 & 5216 INSTALLATION
EASY-TO-CABLE-MANAGE ELITE 5220 & 5216 INSTALLATION - 11/13/17Page 3 of 3
The rotation limits for the arm
are set by placing the stop pins
in the holes corresponding to
where you want the arm to
stop. The stop pin then bumps
into the stop block on the front
of the wall mount ear, stopping
the arm. The stop pins can be
removed and set by hand.
Stop Pin
Stop Block
MONITOR TILT, ROTATION & ADJUST MONITOR DEPTH
MONITOR TILT
& ROTATE
Gently hold sides
of monitor. Tilt and
rotate to desired
position with ball
VESA.
ADJUST
MONITOR
DEPTH
Loosen the
adjustment
knob, move
the Paralink
forward or
back, then
re-tighten
the knob.
Adjustment
Knob
ADJUST ARM LIFTING CAPACITY
ADJUST ROTATION LIMITS - WALL MOUNT
Stop Pin
If foot of Elite is not level:
• Remove long top cover
and front end cover.
• Insert 9/16 socket wrench over nut in end frame.
• From beneath arm, slightly
loosen center bolt with
provided hex key.
• Tighten set screws with
hex key until foot is level,
then retighten center bolt.
Check for level. Repeat if
necessary. If center bolt is
not retightened, the Elite foot
could come loose.
• Replace arm covers.
9/16
socket
wrench
End
frame
REATTACH ARM COVERS
TOP COVERS: Reattach by replacing the two 6-32 x
1/4”atheadscrewsinthecenterofthecoverusinga
Phillips head screwdriver.
CENTER COVER: Reattach by replacing the four
10-24x3/4”atheadscrewsusingaPhillipshead
screwdriver.
END COVERS: Reattach by replacing the two 10-24 x
3/4”atheadscrewsusingaPhillipsheadscrewdriver.
ADJUST BALL VESA TENSION & HEIGHT
Pivot tension
adjustment screws
Use the slider knob
to loosen the slider
to adjust the height
of the monitor on the
Paralink.
Adjust the pivot tension
of the ball by gently
and evenly tightening
or loosening the four
screws on the back of
the ball VESA.
Slider knob
Extend the arm straight out as shown
before adjusting the arm’s lifting
capacity. Be sure all equipment is
mounted on the arm before
adjusting. Adjust the arm
closest to the monitor
rst.UsetheT-handle
provided.
DO NOT USE
POWER TOOLS TO ADJUST
Button
head bolt Set
screws
ADJUST HORIZONTAL TILT ANGLE