Icy Box IB-RD3640SU3E2/SU3 User manual

Manual IB-3640 Series
1
Version 1.1
IB-RD3640SU3E2/SU3
IB-3640SU3

Manual IB-3640 Series
2
Version 1.1
CONTENT
1. Introduction.....................................................................................................................................................................3
1.1 General Information .............................................................................................................................................3
2. Hardware IB-3640 Series...........................................................................................................................................4
2.1 Front View LED Indication.................................................................................................................................4
2.2 Rear View ..................................................................................................................................................................6
2.3 Side View ...................................................................................................................................................................6
3. HDD Installation........................................................................................................................................................7
4. Setting/Changing the RAID mode......................................................................................................................8
5. Disk Initialisation ..................................................................................................................................................11
5.1 Windows 2000 / XP (32/64 bit)..............................................................................................................11
5.2 Windows Vista (32/64 bit) ........................................................................................................................12
5.3 Windows 7 (32/64 bit)................................................................................................................................13
5.4 Macintosh O.S. 10.X .......................................................................................................................................15
6. References ................................................................................................................................................................17

Manual IB-3640 Series
3
Version 1.1
1. INTRODUCTION
1.1 GENERAL INFORMATION
1.1.1 Usage cautions
User should not modify this device. The environmental temperature should be within +5℃~
+35℃.
Note: Port multiplier at host computer needed, if connected via eSATA
1.1.2 Power
Power voltage: DC 12 V.
When using this device, please connect the supplied AC adapter or AC adapter cable to the
power jack of device. When placing the adapter cable, make sure it cannot get damaged or be
subject to pressure. To reduce the risk of electric shock, unplug the adapter first before cleaning
it. Never connect the adapter to the device in a humid or dusty area. Do not replace the adapter
or cable’s wire or connector.
1.1.3 Radio interference/compatibility
- If not properly shielded, almost all electronic devices will get radio interference. Under some
conditions, your player might get interference.
- The design of this device has followed the FCC/CE standard, and has followed the following
rules:
(1) This device may not cause harmful interference;
(2) This device could accept some interference received including interference that may cause
undesired operation.
1.1.4 Repair
If the device has a problem, you should take it to an appointed repair center and let the
specialists do the repair, never repair the player yourself, you might damage the device or
endanger yourself or your data.
1.1.5 Disposing of the player
When you dispose of the device, be sure to dispose it appropriately. Some countries may
regulate disposal of electrical device, please consult with your local authority.
1.1.6 Others
When using this device, please do not let the device come into contact with water or other liquid,
if water is accidentally spilled on the device, please use a dry cloth to absorb the spillage.
Do not let the device come into contact with water or other liquid.
Do not disassemble the device; repair the device or change the design of the device, any damage
done will not be included in the repair policy.

Manual IB-3640 Series
4
Version 1.1
Avoid hitting the device with hard object, avoid shaking the player, and stay away from magnetic
fields.
During electrostatic discharge and the strong electromagnetic field, the product will
malfunction, and then unplug the power cable and the product will return to normal
performance next time it is powered on.
Note: All the information contained in this manual was correct at the time of publication.
However, as our engineers are always updating and improving the product, your device’s
software may have a slightly different appearance or modified functionality than presented in
this manual.
2. HARDWARE IB-3640 SERIES
2.1 FRONT VIEW LED INDICATION
IB-3640SU3
1. Blue Power on
Orange Sleep mode
2. USB in use / access
3. eSATA in use / access
4. Power button It needs to be pressed and held for 3 seconds to power off.
Remark! This design prevents accidental power off.
5. Interface button Function: Off
Function: LED blue – power off with PC
LED yellow – power off & power on with PC
7. Fan button Controls auto & manual modes and fan speed from level 1 to level 3.
8. eSATA link interface option
9. USB 3.0 link interface option
10. Smart Fan automatic mode
11. Smart Fan manual mode
12. Fan speed level 1 below 45 °C 1,200rpm ~ 1,800rpm
13. Fan speed level 2 45 °c · 54 °c 1,800rpm — 2,500rpm
4 5 6 7
3
16
2
1
17 18
19
10 11 12
13
14 15
8
9

Manual IB-3640 Series
5
Version 1.1
14. Fan speed level 3 higher man ss rc 2,500rpm ~ 3,500rpm
16.-19. HDD1 / HDD2 / HDD3 / HDD4
blue active
purple access
IB-RD3640SU3E2 /SU3
1. Blue Power on
Orange Sleep mode
2. Power button It needs to be pressed and held for 3 seconds to power off.
Remark! This design prevents accidental power off.
3. Mode RAID mode button needs to be pressed and held for 3 seconds to switch the
device's raid mode.
Remark! This design will prevent accidental execution of this function.
4. Fan button Controls auto & manual modes and fan speed from level 1 to level 3.
5. SingIe mode
6. RAID 0 Spanning Mode / BIG
7. RAID 0 Striping Mode
8. RAID 1
9. RAID 3
10. RAID 5
11. RAID 10
12. Rebuild
13. USB in use / access
14. eSATA in use / access
15. FireWire in use / access (SU3E2 version only)
16. Smart Fan automatic mode
17. Smart Fan manual mode
18. Fan speed level 1 below 45 °C 1,200rpm ~ 1,800rpm
19. Fan speed level 2 45 °c · 54 °c 1,800rpm — 2,500rpm
20. Fan speed level 3 higher man ss rc 2,500rpm ~ 3,500rpm
2 3 4
14
22
13
1
23 24
25
16 17 18
19
20
21
15
6
7 8 9 10 11
12
5

Manual IB-3640 Series
6
Version 1.1
21. HDD error When any of HDD1 to HDD4 has an error, HDD error is on.
Remark! LED doesn't function in Single mode.
22.-25. HDD1 /HDD2 / HDD3 / HDD4
Blue active
Purple access
Red rebuild
2.2 REAR VIEW
IB-RD3640SU3E2 IB-RD3640SU3 / IB-3640SU3
1. Fan
2. RAID Mode confirmation button (behind the plastic cover)
3. FireWire a port
4. eSATA port
Note: Port multiplier at host computer needed, if connected via eSATA
5. USB 3.0 port
2.3SIDE VIEW
IB-RD3640SU3E2 IB-RD3640SU3 / IB-3640SU3
1. 2x FireWire b port
2. DC Power jack
1
2
3
4
5
1
2
4
5
1
2

Manual IB-3640 Series
7
Version 1.1
3. HDD INSTALLATION
- Please use the provided screws to secure the handles to the 4 HDDs.
- Open the front door.
- Press down the tabs (1) of metal frame to unlock and remove it.
- Take the transport paper board out of the device.
- Slide the 4 HDDs into the guide rails and push them downwards until it locks into the connector in
order from up to down.
- Reinstall the metal frame that was removed in step 3. Please make sure the bottom of the frame
stays inside the track (2) before closing the front door.
- Connect the power adapter and choose one cable to connect to your computer (depends on
version) and power on the device.
- When connected and powered on, the System LED will turn blue; the HDD LED lights will turn blue.
If there are HDDs, the HDD LED will stay blue. If the HDDs are accessed the corresponding HDD LEDs
will flash blue.
IB-3640SU3
- Power on the product and complete the setting inside Disk management of your computer system.
1
2

Manual IB-3640 Series
8
Version 1.1
4. SETTING/CHANGING THE RAID MODE
IB-RD3640SU3E2 /SU3
REMARK: Default setting is RAID 5 mode.
- For RAID mode setup, users need to press and HOLD the RAID button (1) at the front for 3 seconds
until the LEDs are flashing.
Press again for changing the RAID mode.
- After selecting the RAID mode you want, press and hold the confirmation button at the rear panel
(behind the plastic cover) (2) until the device shuts down.
- Power on the product again and complete the setting inside Disk management of your computer
system.
1
2

Manual IB-3640 Series
9
Version 1.1

Manual IB-3640 Series
10
Version 1.1

Manual IB-3640 Series
11
Version 1.1
5. DISK INITIALISATION
5.1 WINDOWS 2000 /XP (32/64 BIT)
If the HDD is uninitialized, you may have to initialize it by doing steps as followed:
- At first click "Start", “Execute" at your PC and key in "diskmgmt. msc".
- After that please press "RETURN" key.
Remark: Windows 2000 / XP (32 /62 bit) only support MBR.
Under Windows 2000 / XP, the HDD total volume shall not be more than 2 TB, otherwise the device
won‘t be recognized.
1. Start disk initialization.
2. Create new partition and format disk.

Manual IB-3640 Series
12
Version 1.1
3. Disk format completed.
5.2 WINDOWS VISTA (32/64 BIT)
If the HDD is uninitialized, you may have to initialize it by doing steps as followed:
- At first click "Start", “Execute" at your PC and key in "diskmgmt. msc".
- After that please press "RETURN" key.
1. Start disk initialization.
Remark: Please enable GPT if the total capacity is more than 2 TB and enable MBR if the total
capacity is less than 2 TB.

Manual IB-3640 Series
13
Version 1.1
2. Create new partition and format disk.
3. Disk format completed.
5.3 WINDOWS 7(32/64 BIT)
If the HDD is uninitialized, you may have to initialize it by doing steps as followed:
- At first click "Start", “Execute" at your PC and key in "diskmgmt. msc".
- After that please press "RETURN" key.

Manual IB-3640 Series
14
Version 1.1
1. Start disk initialization.
Remark: Please enable GPT if the total capacity is more than 2 TB and enable MBR if the total
capacity is less than 2 TB.
2. Create new partition and format disk.
3. Disk format completed.

Manual IB-3640 Series
15
Version 1.1
5.4 MACINTOSH O.S. 10.X
If the HDD is uninitialized, you may have to initialize it by doing steps as followed:
1. Click Disk Utility icon
2. HDD initialise…
3. Click Erase

Manual IB-3640 Series
16
Version 1.1
4. Click Erase
5. HDD format in process
6. Format completed

Manual IB-3640 Series
17
Version 1.1
6. REFERENCES
1. Changing the RAID mode will cause data lost.
2. Please refer to the instructions when switching the RAID mode, otherwise the execution
might fail.
3. Interface of USB / eSATA / (Firewire) cannot be used at the same time.
4. When using the RAID function, HDD’s with the same brand, model and capacity is strong
recommended.
5. When using RAID function, more than one HDD partition is not recommended.
6. Under Windows Vista /7, users can enable GPT when initializing HDD with a total capacity of
more than 2 TB.
7. Older OS may not recognize the device if you use a different operation system than Windows
Vista / Windows7. For more detailed information about GTP, please visit:
http://msdn.microsoft.com/en-us/library/windows/hardware/gg463525.aspx
8. If users enable MBR by mistake, in order to clean the partition table, you have to switch to
another RAID mode and do the RAID mode switch all over again referring to Setup. Then go
back to the RAID mode you want, repeat the previous actions and enable GPT when
initializing HDD.
9. For Macintosh users: the total capacity of more than 2 TB could be recognized only for the
operation system 10.4.11 Tiger or later.
10. Do not connect the device to the SATA on board port of the motherboard. Either use SATA to
eSATA PCI-Express or SATA to eSATA PCI add-on card; otherwise the PC (Windows /
Macintosh) may not recognize the device.
11. In RAID 1, HDD1 and I-IDD2 must be installed; otherwise the PC (Windows / Macintosh)
cannot recognize the device.
12. Rebuild time is based on the capacity, e.g. it takes about 1 hour for 200 GB.
13. When the USB / eSATA cable is plugged out, the device goes to sleeping mode
automatically.
14. To take out the HDD from the device, slightly press down the handle of the tray and pull it
out.
15. Setting up motherboard‘s power management in S3 is recommended.
(For more details refer to the user guide of motherboard BIOS setting).
16. If the device takes too long to initialize, please check if the HDD is securely installed or
update the SATA host driver version.
17. If the transfer rate is not normal, please check if the setting of SATA disk jumper is 1.5 or 3.0
Gbit/s.
18. If there is noise with the fan, power off the device, unscrew the fan, take out the cover,
clean the fan end assemble it back.
19. If the noise is still present, you can change the fan with another identical fan of Size
80X80X20mm.
20. If the fan stops working, do not dismantle it. Please send back to the retail store immediately.
21. Temperature 0 ~ 60 °C
Humidity 90 RH
22. Smart fan controlled by the built-in thermal sensor and it comes with 2 modes (auto/manual)
and 3 levels of speed:

Manual IB-3640 Series
18
Version 1.1
Level 1: below 45 °C 1,200rpm ~ 1,800rpm
Level 2: 45 °C ~ 54 °C 1,800rpm ~ 2,500rpm
Level 3 : higher than 55 °C 2,500rpm ~ 3,500rpm
23. Operation System:
Windows XP (32/64bit)
(with MBR enabled, supports total capacity up to 2 TB )
Vista (32/64bit) / Windows 7 (32/64bit)
(with GPT enabled, supports total capacity more than 2TB )
Macintosh 10.X or later
24. Support USB transfer speeds of low speed (up to 1.5 Mbit/s), full speed (up to 12 Mbit/s),
high speed (up to 480 Mbit/s), super speed (up to 5 Gbit/s), eSATA transfer speed (up to
1.5~3.0 Gbit/s), Firewire a (up to 400 Mbit/s), Firewire b (up to 800 Mbit/s).
Note: Port multiplier at host computer needed, if connected via eSATA
© Copyright 2012 by RaidSonic Technology GmbH. All Rights Reserved
The information contained in this manual is believed to be accurate and reliable. RaidSonic Technology GmbH assumes no
responsibility for any errors contained in this manual. RaidSonic Technology GmbH reserves the right to make changes in the
specifications and/or design of the above mentioned product without prior notice. The diagrams contained in this manual may
also not fully represent the product that you are using and are there for illustration purposes only. RaidSonic Technology GmbH
assumes no responsibility for any differences between the product mentioned in this manual and the product you may have. All

Manual IB-3640 Series
19
Version 1.1
the information contained in this manual was correct at the time of publication. However, as our engineers are always updating
and improving the product, your device’s software may have a slightly different appearance or modified functionality than
presented in this manual.