IDEAL INDUSTRIES CREE LIGHTING 304 Series User manual

1 of 3 CI350X01R1_A
304 Series™
LED Parking Structure
Direct, Hook and Cord, Pendant and Adjustable Mount
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed
including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. DANGER- Risk of shock- Disconnect power before installation.
DANGER – Risque de choc – Couper l’alimentation avant l’installation.
2. This luminaire must be installed in accordance with the NEC or your local electrical
code. If you are not familiar with these codes and requirements, consult a qualied
electrician.
Ce produit doit être installé conformément à NEC ou votre code électrique local.
Si vous n’êtes pas familier avec ces codes et ces exigences, veuillez contacter un
électricien qualié.
3. When handling, hold luminaire on sides to prevent damage to the top screen or
LED’s.
4. Take care to keep the LED lenses clean during installation.
SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE
TO INSTALL:
DIRECT MOUNTING
STEP 1:
Remove the junction box mounting bracket from the
luminaire by loosening (2) screws and sliding it out of
the channels of the luminaire support bracket. See
Figure 1 and 3.
STEP 2:
Attach the junction box mounting bracket to the
customer supplied junction box using the customer
supplied screws.
STEP 3:
Temporarily hang the luminaire from the hook-shaped
projection on the junction box mounting bracket. See
Figure 2.
STEP 4:
Make wiring connections per the Electrical
Connections section.
STEP 5:
Secure the cord plate/gasket assembly to the junction
box mounting bracket using (2) supplied screws.
STEP 6:
Remove the luminaire from the junction box mounting
bracket and slide the channels on the luminaire
support bracket onto the flanges of the junction box
mounting bracket. See Figure 3.
STEP 7:
Secure the luminaire to the bracket using the (2)
screws that were loosened in Step 1.
1
2
3
Junction Box
Mounting Bracket
Luminaire Support
Bracket
Loosen (2)
Screws
Hook-shaped
Projection
Luminaire Support
Bracket
Junction Box
Mounting Bracket
Junction Box
Mounting Bracket

2 of 3 CI350X01R1_A
PENDANT MOUNT
NOTE: Ensure that the customer supplied pendant is
capable of supporting the weight of the luminaire.
STEP 1:
Size the pendant and locate the junction box accordingly.
Install a suitable Listed cord strain relief bushing in the
junction box, and feed the luminaire’s supply cord through it.
Tie an overhand knot in the cord inside the junction box.
STEP 2:
Make wiring connections to the cord and supply wiring per
the Electrical Connections section.
STEP 3:
Attach the junction box cover/pendant assembly to the
junction box using customer supplied screws.
STEP 4:
Secure the pendant to the luminaire mounting bracket using
a customer supplied suitable conduit fitting. See Figure 4.
HOOK AND CORD MOUNTING
STEP 1:
Push down on retainer spring until top of spring is free of
luminaire hook. See Figure 5.
STEP 2:
Slide hook into securely mounted customer supplied eye
hanger and return retainer spring to original position.
NOTE: The luminaire should already be factory set for
correct balance. However, should you need to, the luminaire
may be balanced by loosening the hook adjustment set
screw on the top of the housing and sliding the hook as
necessary for correct balance. Tighten hook set screw when
finished. See Figure 5.
STEP 3:
Install a suitable Listed cord strain relief bushing in the
junction box, and feed the fixture’s supply cord through it. Tie
an overhand knot in the cord inside the junction box.
STEP 4:
Make wiring connections to the cord and supply wiring per
the Electrical Connections section.
ADJUSTABLE MOUNT
STEP 1:
Secure the top of the Adjustable Arm to mounting surface
with screws (not supplied).
STEP 2:
Make wiring connections per the Electrical Connections
section.
4
Luminaire Mounting
Bracket
Conduit Pendant (Customer
Supplied)
Conduit Fitter (Customer
Supplied)
5
Hook Adjustment Set
Screw
Retainer Spring
6Adjustment Arm

3 of 3 CI350X01R1_A
www.creelighting.com
© 2019 Cree Lighting, A company of IDEAL INDUSTRIES. All rights reserved. For informational purposes only. Content
is subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree®and the Cree logo are
registered trademarks of Cree, Inc. 304 Series™ is a trademark of Cree Lighting, A company of IDEAL
INDUSTRIES.
ELECTRICAL CONNECTIONS- PHASE TO NEUTRAL WIRING
– 120/277V
a. Connect the black luminaire lead to the line supply lead
b. Connect the white luminaire lead to the neutral supply
lead
c. Connect the green or green/yellow ground lead to the
supply ground lead
ELECTRICAL CONNECTIONS- PHASE TO PHASE WIRING –
208/240/480V
a. Connect L1 (Hot) supply lead to the black lead.
b. Connect L2 (Hot) supply lead to the white lead
c. Connect the green or green/yellow ground lead to the
supply ground lead
BLACK
OR L1 (HOT)
GROUND
LINE-BLACK
GROUND-GREEN
NEUTRAL-WHITE
SUPPLY WIRING
LUMINAIRE
WHITE
OR L2 (HOT)
ADJUSTING HEIGHT OF LUMINAIRE
If desired, the position of the luminaire can be adjusted as follows:
STEP 1:
Remove set screw. See Figure 7.
STEP 2:
Loosen adjustable knob. See Figure 7.
STEP 3:
Rotate luminaire to desired position. Use the alignment slot to align
with a letter in the table, above, which will correspond to the fixture
degree (figure 6 is shown at 0 degrees)
STEP 4:
Tighten Adjustment Knob to hold luminaire in place.
STEP 5:
Insert Set Screw into hole that corresponds with the letter in table on
the left.
7
Adjustment Knob
Alignment
Slot
Set Screw
DEGREE ADJUSTABLE FIXTURE
POSITION (FIGURE 7)
90 A
85 B
80 C
75 D
70 E
65 F
60 G
55 H
50 I
45 J
40 K
35 L
30 M
25 N
20 O
15 P
10 Q
5 R
0 S