idealin fogging systems ROTO120 User manual

04-2009
FEATURES:
• is an oscillating device generally used as an accessory with humidifiers. It should be
operated on a 220 ~ 240 Volt AC, 50 Hz, single phase power supply only. Its purpose is to continuously
oscillate the portable humidifier placed on it @ 120 degrees max.
• The equipment is shipped in two parts: ROTO-120 base & ROTO-120 Tray (also known as Round Tray).
• The Roto-120 Tray supplied with the product is to be mounted on the Rotostand shaft and then the
humidifier needs to be simply placed on top of the tray.
• can rotate the tray at a max. Angle of 120 degrees (60 degrees each side) only.
• Only 1 (One) humidifier can be oscillated on the product.
• It is supplied with a plug to directly connect to a 5 amps socket. A socket is also provided on the Roto-120
to connect the humidifier to it.
• Roto-120 ensures UNIFORM distribution of fog particles in an enclosed area, which is most essential
for humidification jobs.
• NIL maintenance and trouble free operation.
OPERATION:
• Place the Roto-120 on a level surface OR install it at a desired height using “STAND L Angle” supplied by
Idealin. Alternatively, use a support base (max. 2 fts. x 2 fts). If using wooden ply for a support base, ensure
that the thickness of wooden ply is adequate to support a weight of around 25 kgs. Generally 10mm to
15mm thickness is sufficient.
• A shaft (with a cut at the centre) protrudes from the Roto-120. At the same time, the “Round Tray” supplied
with the product is pre-fitted with a rod which has a round opening at the centre. Simply slide the rod over
the shaft of the round tray.

Page 2 of 2
• Gently move the ROUND TRAY either left or right till you hear a clinch noise and find that the tray cannot
be moved manually any more. There is a pin inside the rod which will fit exactly inside the cut on the shaft
- thus ensuring that the tray is securely mounted. When the tray has been mounted securely on the shaft,
the tray will offer resistance to manual movement. Do not force the tray to manually move any further.
Tighten the two screws on the rod for firm mounting.
• Connect the plug to a standard 5 amps. Socket and switch on power supply. The tray will now oscillate in
co-ordination with the shaft. Switch OFF the power supply to the
• Carefully lift the humidifier and place it on the tray. Ensure it is not placed on the edge of the tray.
• Switch ON power supply to both the Roto-120 and the product placed on it. You will find that there is co-
ordination in the movement and fog particles are being distributed uniformly.
•
DO NOT FORCEFULLY ADJUST THE DIRECTION OF THE MOVING TRAY AS IT IS SECURELY
CONNECTED TO THE SHAFT AND YOU MAY UNINTENTIONALLY DAMAGE THE MOTOR BY
DOING SO. Simply lift the portable humidifier placed on the round tray, adjust the desired angle and
place it back on the tray.
• The speed of the system is set at 1 RPM and should not be tampered with. Higher speed levels may cause
jerks to the products placed on the Roto-120 and can also damage the equipments.
• Can be operated in a 24 x 7 module.
CAUTION:
• Use of a Ground Fault Receptacle (Earthing) is strongly recommended for all products.
• Before turning on the power supply to the ROTOSTAND, ensure that the round tray is properly
mounted on the shaft of the ROTOSTAND. If the tray is not securely mounted, you can damage both
the Roto-120 and the humidifier placed on it. Follow instructions in “Operation” above to secure
mounting.
• Before removing the round tray from the turn off power supply to the equipment &
unscrew both screws from the shaft.
O ne Y ear L imited W arranty
WARRANTY WILL BE VOID IF THE PRODUCTS ARE FOUND DAMAGED RESULTING FROM DIRECT
OR INDIRECT MISUSE; ABUSE; NEGLIGENCE; ACCIDENT; LACK OF MAINTENANCE OR
UNAUTHORISED REPAIRS OR ALTERATIONS WHICH AFFECT THE PRODUCTS PERFORMANCE OR
RELIABILITY.
Manufacturer’s Standard Warranty Clause applies
---x---x---x---