IDS X Series User guide

2
IDS X-Series Installer Manual 700-398-02O

3
IDS X-Series Installer Manual 700-398-02O
Contents
Contents ........................................................................................................................................................................................3
1. Keypads ....................................................................................................................................................................5
2. Introduction to the IDS X-Series...............................................................................................................................7
Features of the IDS X-Series .......................................................................................................................................................... 7
3. Installation and Wiring...............................................................................................................................................8
Installation Requirements..............................................................................................................................................................9
End-of-Line Resistors ....................................................................................................................................................................9
Box Tamper Input ..........................................................................................................................................................................9
Connecting the Telephone Communicator - Advanced ................................................................................................................9
Programmable Outputs.................................................................................................................................................................9
Key-Switchor Remote Control Unit ...............................................................................................................................................9
Installing Expander Modules..........................................................................................................................................................9
IDS Remote Receiver .....................................................................................................................................................................9
Transmitter Connection ................................................................................................................................................................9
Hardware Default Switch.............................................................................................................................................................10
Keypads .......................................................................................................................................................................................10
Replacing a DamagedKeypad/Bus-wired Peripheral ...................................................................................................................10
Defaulting Keypads ..................................................................................................................................................................... 11
4. Event Log................................................................................................................................................................11
5. Access Codes.........................................................................................................................................................11
Normal User Code ....................................................................................................................................................................... 11
Master User Code ........................................................................................................................................................................ 11
Maid’s Code (Arm to Disarm Code) ............................................................................................................................................. 11
Duress Code................................................................................................................................................................................. 11
Installer Code............................................................................................................................................................................... 11
Maintenance Code....................................................................................................................................................................... 11
Download Code ...........................................................................................................................................................................12
6. How to Read Location Values ................................................................................................................................12
7. Programming of the Panel......................................................................................................................................12
8. Programming Quick Reference Guide....................................................................................................................13
9. Programming Location Summary...........................................................................................................................14
Zones...........................................................................................................................................................................................14
Global Setup ................................................................................................................................................................................16
Daylight Savings ..........................................................................................................................................................................20
Miscellaneous–Advanced ...........................................................................................................................................................21
Phone Numbers...........................................................................................................................................................................24
Zone Properties ...........................................................................................................................................................................25
No Movement–Advanced ...........................................................................................................................................................27
Security Codes.............................................................................................................................................................................28
Partition Options .........................................................................................................................................................................29
Delays ..........................................................................................................................................................................................30
Options to Configure Keypads..................................................................................................................................................... 31
aXess Control...............................................................................................................................................................................32
Wireless Integration Options.......................................................................................................................................................32
Reporting Codes - Advanced .......................................................................................................................................................32
Global Reporting Codes ...............................................................................................................................................................32
Zone Reporting Codes .................................................................................................................................................................35
Partition Reporting Codes ...........................................................................................................................................................36
User Reporting Codes.................................................................................................................................................................. 37
Programmable Outputs...............................................................................................................................................................38
Output Disarm Clear....................................................................................................................................................................38
Partition Event Driven Outputs–Advanced.................................................................................................................................39
Zone Programmable Output Events............................................................................................................................................40
Output Pulse Timing - Advanced.................................................................................................................................................41
Output Scheduling On Time - Advanced .....................................................................................................................................41
Output Scheduling Off Time - Advanced.....................................................................................................................................42
Output Scheduling On/Off Days - Advanced...............................................................................................................................42
Event Reporting Options - Advanced ..........................................................................................................................................43
10. Touch Keypad Switch to Programmable Output Mapping .....................................................................................45
11. Voice Module ..........................................................................................................................................................45

4
IDS X-Series Installer Manual 700-398-02O
12. Xwave2Outputs ......................................................................................................................................................45
13. LCD Keypad Information ........................................................................................................................................45
14. Panel Information....................................................................................................................................................46
15. User Options...........................................................................................................................................................46
16. Appendix .................................................................................................................................................................47
17. Hardware Identification...........................................................................................................................................49
18. Serial Communication Jumper Settings .................................................................................................................49
19. Trouble Display.......................................................................................................................................................50

5
IDS X-Series Installer Manual 700-398-02O
1. Keypads

New LCD KEYPAD
Keypad Indicator Icons
Power indicator icon has two functions:
1. When the icon is on, this indicates the keypad is powered up.
2. Flashing indicates an issue has occurred and needs your attention.
Armed icon indicates the system is armed either in ‘away’ or ‘stay’ mode. The LCD will
display the armed mode.
Unarmed icon will be illuminated when the system is not armed.
Alarm icon will flash when an alarm condition has occurred.
Button Details
Partition Button is to select a partition that you would like to interact with via the keypad.
NOTE: Only available if the keypad is configured as a global keypad!
Stay Button allows you to select which stay profile to stay arm the system with.
NOTE: Only available if more than one stay profile has been programmed. (see X-Series user
manual)
Switch Button has two functions:
1. Access to outputs that could be used to switch devices, lights on/off or open/close gates, etc.
(Function not currently implemented)
Bypass button allows you to disable zones so that they cannot violate the alarm.
Chime button selects which zones, will cause the keypad to chime when violated while the system is
disarmed.
Navigation buttons allows you to scroll through menus, and when editing zone names, etc.
Press and hold left arrow buttons to change the keypad sounds.
Panic button when held down for 3 seconds will sound the siren and send a panic signal to the
security company if the alarm is configured to do so.
LCD Display
Power, Armed, Unarmed, Alarm Indicators
Touch keys

7
IDS X-Series Installer Manual 700-398-02O
2. Introduction to the IDS X-Series
Thank you for purchasing an IDS Alarm Panel.
The IDS X-Series alarm is a versatile, Bylaw 25 compliant, expandable Alarm Panel. It comes in three versions, X8, X16 and X64.
Both have up to 8 partitions and can have 8 keypads. The X16 can be expanded from 8 to16 zone, the X64 from 8 to 64 zones
and the X8 only has 8 zones with no dialler. Most features are configurable and may be programmed directly through a keypad
or via serial PC connection or telephone system, using the IDSwift 2 Download Software and appropriate modem (P/N: 860-36-
0001).
There are up to 64 programmable burglary zones on the X64, 16 programmable burglary zones on the X16 and 8 programmable
burglary zones on the X8. A dedicated panic zone, monitored siren output, auxiliary power output, and 5 onboard programmable
outputs expandable to 41 outputs with the 860-07-596 Output expander on the X-Series, are available.
For correct operation, the IDS X-Series panels must be used in conjunction with the specified transformer/battery combination
(ask your sales representative for a copy of the IDS Power Budget spreadsheet to identify your needs) and appropriate peripheral
sensors andsignalling devices.
NOTE: X-SERIES products are not compatible with any previous IDS products, such as the IDS816 and IDS1632.
Features of the IDS X-Series
Zones and Partitions:
➢8 onboard zones, expandable to 16 onboard zones with a X-Series 8-zone Plug-in Expander
(P/N: 860-06-X-08PI) –A very cost-effective 16 zone solution
➢Further expandable to 64 zones with the use of up to 6 bus-wired X64 8-zone Unpowered Expander modules (P/N:
860-06-X-08S) or 8 keypad zones - 1 per keypad
➢All zones can be expanded with wireless receivers to receive signals from the Duevi or the Xwave range of enabled
wireless detectors. All wireless zones are fully supervised.
➢The system can also have a hybrid of wired and wireless zones totalling 64 zones for the X64 and 16 zones for the X16
and 8 for the X8.
➢8 partitions
➢4 stay profiles per partition
Users:
➢128 users
➢Options to set user codes as Master, Duress, Maid, Arm only, Disarm only or Output Trigger.
System Options:
➢Tamper reporting per zone using double end-of-line resistors (12K and 4K7)
➢5 programmable outputs on the Alarm Panel, expandable to 41 when using zone expanders (2 per expander),
keypads (1 per keypad) and output expanders (8 per expander)
➢Event log (1000 events) date and time relative
➢Auto arm/disarm capability per partition and by day of the week.
➢No movement auto arm and medical reporting
➢Panel firmware installer upgradable via serial data cable
➢Telephone communicator that supports Ademco, FBI, Silent Knight, Contact ID, and SIA
➢Fax defeat/answering machine override
➢Dual reporting provides for duplicated reporting to two independent central base stations
➢Split reporting to report to either 1 of 2 dual reporting number pairs
➢Comprehensive lightening protection
➢Dynamic battery self-test
➢Low battery monitoring and cut-out circuit
➢Dual power supply, with an independent battery charging circuit, means more onboard power for simplified alarm
installation
➢Voice module support (860-06-X64-0412). Only version “D” hardware and above.
➢Xsms support from version 2.34 to control the alarm via smses
➢2 x 8 channel output expander support. (Firmware version 2.50 and above)

8
IDS X-Series Installer Manual 700-398-02O
3. Installation and Wiring
*The kick start jumper must be in-circuit when using only a battery (i.e. no AC). Simply short the pins out with a screwdriver,
or use a jumper. Remove the short/jumper once the Panel Status LED lights up (indicating power up), as leaving it on
disables the low battery cut-out.*
Figure 1: Connection Diagram
Note: When using extra power supplies to power any peripheral connected to the keypad bus an IDS RS485 isolator (860-06-
0557) must be used.

9
IDS X-Series Installer Manual 700-398-02O
Installation Requirements
➢A suitable transformer with an output voltage of 16 VAC ±10% with a 32VA minimum rating must be used. A 40VA
transformer is recommended.
➢A 12V sealed lead acid battery with a capacity of 7AH must be used. The backup period after mains failure will depend on
the number of keypads, sensors, and bus-wired peripheral devices connected to the system.
➢Connect a 12V self-driven siren or piezo siren (not a horn speaker) to the siren output.
➢The panel can supply a total continuous current of 750mA to bus-wired peripheral devices such as keypads, remotes,
receivers, passives etc; from Aux 12V terminals.
End-of-Line Resistors
➢All zones, including Panic zones, are end-of-line supervised.
➢All zones, whether they are used or unused, need to be terminated with a 3K3 resistor (resistor colour-code is orange,
orange, red, gold).
➢For maximum security, the end-of-line resistor must be placed inside or as close to the sensor as possible.
➢For tamper by zone, 4K7 and 12K end-of- line resistors must be connected instead of a single 3K3 resistor.
➢If the panel is unarmed and a tamper condition occurs, the siren will not sound but a tamper condition will be reported if it
is enabled to do so. See Table 41to enable/disable this option.
➢If the panel is armed and a tamper condition occurs, an audible alarm will register, and a tamper condition AND zone
violation will be reported.
Box Tamper Input
The box tamper input does not require an end-of-line resistor, but does require a normally closed contact. The panel is shipped
with the box tamper input bypassed. To use it, remove the jumper and connect a normally closed contact onto the terminals.
Refer to Figure 1: Connection Diagram
Connecting the Telephone Communicator - Advanced
Refer to: Figure 1: Connection Diagram
For optimum lightning protection, connect a low resistance earth to the communicator earth input.
➢Connect the telephone communicator in line seizure mode and never in parallel with the telephone.
➢Ensure the telephone receiver is connected to the communicator terminals marked “phone” and the incoming line to the
terminals marked “line”.
Programmable Outputs
A relay must be used when any device requiring a current greater than 50mA is connected to an onboard programmable output.
The onboard programmable output circuitry is a current sink circuit with a maximum output voltage of 13.6Vdc and a maximum
output current of 50mA. Programmable outputs are primarily connected for radio transmitter. The output expander, part no.
860-06-0596, has eight 1 amp DC relays to be able to manage a higher current to be used for connecting, LEDs, sirens, bus-wired
peripherals, etc.
Key-Switchor Remote Control Unit
A key-switch, (not recommended) or non-IDS remote receiver maybe connected to any zone to allow remote arm/disarm and
remote panic capability.
➢When using a key-switch or remote control unit, a 3K3 resistor must be connected between the zone input and ground.
➢Use only a spring-loaded momentary key-switch or non-latching remote control unit.
Installing Expander Modules
When installing expander modules please refer to the document supplied with the module. Note that up to 6 bus-wired, 8-zone
expander modules (P/N: 860-06-X-08S), 1 plug-in expander (P/N: 860-06-X-08PI) and 2 bus-wired output expanders may be
added to the IDS X64 Alarm Panel. Zones 9-16 are reserved for the Plug-in Zone Expander module which may be used on the X16
as well.
IDS Remote Receiver
Up to 4 IDS Remote Receivers (P/N: 860-07-X02-DI) may be connected to the keypad Bus. Using this facility allows remote arming
and disarming of the panel while providing user identification for a maximum of 128 remotes. For a full list of features and
benefits of the receiver, please see the manual that comes with it.
Transmitter Connection
When connecting a GSM transmitter, use the TX terminal provided on the panel to supply power to the transmitter. This
output is protected by a 4 Amp fuse. This will also help protect the battery by cutting power to it to stop it from being drained.
Note: Do not use with high power transmitters that draw more than 1.5Amps.

10
IDS X-Series Installer Manual 700-398-02O
Hardware Default Switch
Use the hardware default switch (refer to Figure 1) to return the panel to its factory default settings.
The procedure to default the panel is as follows:
1. Remove the battery and AC power from the panel
2. If you are only using a battery make sure that the kick-start jumper is in circuit
3. Hold down the default switch and reapply power to the panel (battery or AC)
4. Wait for the Panel Status LED to flash
5. Release the default switch
6. Remove the kick-start jumper, if one was used
7. Defaulting is complete once the Panel Status LED starts flashing
The effects of applying the default:
1. Factory default values are restored to all locations
2. All attached keypad IDs are defaulted
3. The event log is not cleared
4. The “system default” event is logged to the event log
NOTE: The hardware default switch can be disabled in location 35.
See also: Defaulting the Panel or Master User Code –location 0Enrolling Keypads and Other Bus-wired Peripherals
Keypads
Keypads must be enrolled on the system before they can be used. Keypads are allocated an ID in the order in which they are
enrolled. To enrol a keypad:
1. Wire it to the keypad BUS
2. Power the system up
3. Press the[#]key
Repeat this process with the remaining keypads where more than 1 keypad is used. The first keypad enrolled will have an ID of
1, the second enrolled will have an ID of 2, the third an ID of 3 etc.
NOTE:
➢All the zone and LEDs will flash on a keypad that does not have an ID.
➢The POWER and READY LEDs will be on for a keypad that has an ID and no zone violations.
➢Only the POWER LED will be on for a keypad that has an ID with a zone violation. The LED for that zone will also flash.
Trouble shooting
If the ID process, for an LED keypad, has failed zones 1-8, and zones 9-16 will flash alternately. At this point press the [#] key to
retry.
If the flashing persists, try the following steps:
1. Check all wiring
2. Check that you have not exceeded 8 keypads on the bus
3. Contact the IDS helpdesk for further support
NOTE: To enrol other devices (IDS Remote Receivers or Zone Expanders); consult the installation manuals for those devices. The
IDS X64Alarm Panels can accept6 zone expanders and 4remote receivers.
Replacing a DamagedKeypad/Bus-wired Peripheral
To replace a damaged device (non-dipswitch –like a keypad):
1. Disconnect only the faulty device while the system is powered down.
2. Program a value of [4] into location 0 to free up all redundant IDs (previously unallocated IDs remain free), wait for
approximately 30 seconds then continue to step 3.
3. Connect the replacement device and enrol it –by pressing [#] for keypads –it will now be enrolled in the first available
address.
NOTE:
➢If other devices are disconnected (or damaged), at the time of performing step 2, their addresses will also be freed. Any
new devices being enrolled will automatically be allocated addresses beginning from the lowest free address.
➢When you free up the ID of the damaged unit, the panel settings, relevant to the ID, will be defaulted too. Therefore, the
keypad will need to be re-added to a partition.
➢If a new keypad was enrolled, go to location 243 to check the keypad’s ID (1-8).
Solution
If there are problems with device IDs on a complex installation, do not assign IDs randomly, rather, at the end of the installation,
default all device IDs and then enrol them in sequence.
To re-enrol a Zone Expander or a Remote Receiver; consult the installation instructions for the particular device.