IDTECH EconoScan II User manual

Ver. Oct 2011
Configuration Guide

Mar 2011
Mar 16, 2011
Add “Median Cut-off” function and default barcode ID table”
Mar 2011
Mar 29, 2011
Add “Continuous recognition/No Trigger” mode
Oct 2011
Oct 20, 2011
Add “Function key emulation barcode”

Table of Contents

Continuous recognition / Flash
Button switch mode
Turn OFF mode after identification (Default)
Continuous recognition
Test reading mode
Continuous recognition / LED on
Continuous recognition / Timeout off
Bar level setting
Bar = High <Default>
Bar = Low
Continuous recognition / No trigger

Set Prefix Characters
Set Suffix Characters
G1 Insert Character
G2 Insert Character
G1 Insert Character Location
G2 Insert Character Location
Prefix Barcode Data Suffix
Prefix / Suffix
Prefix /Suffix String
A max. of 10 ASCII characters could be added before or after the bar code data.
No action can be done if it is set to 0.
Format:
Instructions:
1.Read start of configuration
2.Read Set Prefix/Suffix label.
3.See table of ASCII code, find the desire characters by reading
Decimal Digits on Appendix (ASCII table).
4.Read the “Validate” label to complete this setting.
5.Read End of configuration code.
G1/G2 group of characters
Each group could add a max. of 10 ASCII characters. Characters can not be insert
when it is set to 0.
Instructions:
1.Read start of configuration
2.Read G1/G2 insert character
3.Find the desire characters by reading Appendix (ASCII table).
4.Read G1/G2 insert character location
5.Scan the desire location on Appendix (ASCII table).
6.Read the “Validate” label to complete this setting.
7.Repeat the same steps for G2.
8.Read End of configuration code.

Germany Keyboard

Enable Delay between Reread <Default 00>
Appendix 00-0AH

Enable <Default 00>
Appendix (00-0AH)

CR
LF
Tab

After median cut-of
f See appendix A(00-0DH)
Before median cut-off
See appendix A(00-0DH)
Instructions:
1.Read “Before median cut-off” or “After median cut-
off” barcode.
2.Read decimal value barcode on appendix (00~32H).
3.Read validate barcode.
Notes:
1.Before the median cut-off: when set to 0, it won’t
delete the barcode in front of the data.
2.After the median cut-off: when set to 0, it won’t
delete the barcode behind the data.
Truncation

After median cut-off
See appendix A(00-08H)
Before median cut-off
See appendix A(00-08H)
Instructions:
1.Read “Before median cut-off” or “After median cut-
off” barcode.
2.Read decimal value barcode on appendix (00~32H).
3.Read validate barcode.
Notes:
1.Before the median cut-off: when set to 0, it won’t
delete the barcode in front of the data.
2.After the median cut-off: when set to 0, it won’t
delete the barcode behind the data.
Truncation

After median cut-off
See appendix A(00-0DH)
Before median cut-off
See appendix A(00-0DH)
Truncation
Instructions:
1.Read “Before median cut-off” or “After median cut-off”
barcode.
2.Read decimal value barcode on appendix (00~32H).
3.Read validate barcode.
Notes:
1.Before the median cut-off: when set to 0, it won’t delete
the barcode in front of the data.
2.After the median cut-off: when set to 0, it won’t delete
the barcode behind the data.

After median cut-off
See appendix A(00-08H)
Before median cut-off
See appendix A(00-08H)
Truncation
Instructions:
1.Read “Before median cut-off” or “After median cut-off”
barcode.
2.Read decimal value barcode on appendix (00~32H).
3.Read validate barcode.
Notes:
1.Before the median cut-off: when set to 0, it won’t delete
the barcode in front of the data.
2.After the median cut-off: when set to 0, it won’t delete the
barcode behind the data.