IDTECH Ez One Shot User manual

Version: 2015.1
Ez One Shot
UNIVERSAL
USER’S
MANUAL

7-8
12
LED & Beeper Indication..............................................
8
9
Reading Mode .........................................................11
10
5-6
4
2-3
Send Data Length, Preamble, Postamble................
15
Advanced Autosensing and Idle Mode Setting.......
16
Interface.................................................................
Bluetooth Profile.....................................................
Pincode Setup........................................................
Getting Connected - iOS & Android ......................
Power Off Timeout.................................................
Set Bluetooth Device ID.........................................
Set SPP Pincode....................................................
SPP Master Mode..................................................
Batch Mode, Binary Check Character....................
SPP Remote Control, Shut Down, Disconnection..
Memory Mode - Memory Mode, Delete Record.....
Memory Mode - Data Format, Date & Time Setup.
Memory Mode - Date Format, Time Format...........
Table of Contents.......................................................
Cloning Mode............................................................
How to fix the scanner to the terminal.......................
How to change a cable.................................................
How to set up the parameter........................................
Default, Abort, Check Version, Setup Code Read....
Interface, Computer Type.......................................
1
2
17-18
Beep tone, Terminator..............................................
3
19
4
20
Accuracy Adjustment................................................
5
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Code ID, Inverse Barcode........................................
6
Symbologies Code Identifier.....................................
7
Set Code ID....................................................
8~9
Inter-block and Inter-character Delay.....................
10
Keyboard Layout....................................................
Caplock Mode, Numeric Key..................................
11
12
13
14
15
16
17
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33 Memory Mode - Quantity........................................
18
RS232 - Baud rate, Data bits, Parity.......................
RS232 - Stop bit, Handshaking, ACK/NAK,
Flow Control, BCC..................................................
Wand Emulation ....................................................
GENERAL SETTINGS (GROUP 1 - 12)
PREFACE
CONTENTS
Bi-color Setting ......................................................
13
Advanced Autosensing Setting ..............................
14
TETHERED SCANNER SETTINGS (GROUP 13 - 19)
WIRELESS SCANNER SETTINGS (GROUP 20 - 33)

67
DataBar(RSS) Stacked, Limited, Expanded...........
68-76
77-79
80-82
52~60
61~63
64~66
83-86
87-88
89-90
Code 39 (Full ASCII/Standard), Code 32...............
Industrial 2 of 5, Matrix 2 of 5.................................
34~36 Enable/Disable Barcode Symbology.......... 43-45
SYMBOLOGIES (GROUP 34 - 51)
FULL ASCII(CODE39)TABLE, FUNCTION
KEY TABLE(GROUP 52 - 66)
APPENDIX
45
China postcode(Toshiba code)...............................36
37 MSI code, UK Plessey code...................................47
49
Code 93, Telepen, IATA..........................................38
Interleaved 2 of 5, Code 11.................................... 51 39
40 53
41 Codabar..................................................................55
ABC Codabar, CX Codabar....................................
42 57
58
43 Codabar Coupling...................................................
44 59
45 UPC-E....................................................................61
46 UPC-E(0)&(1), UPC-E EXPAND............................ 62
UPC-A....................................................................
47 63
64
65
66
48 EAN-8.....................................................................
EAN-13, ISSN, ISBN, ISMN...................................
49
50
51
EAN/UCC 128, Code 128, PDF417........................
Full ASCII table(Code 39)...........................
Trouble Shooting.........................................
Function Key table(Code 39) for PC-AT......
Appendix 1 Default table........................................
Appendix 2 Cable Pin Assignment.........................
Appendix 3 Barcode test chart...............................
CONTENTS

LED & BEEPER INDICATION
Scanner
Cradle
Status
Status
Blue/Green LED
Blue LED
Red LED
Red LED Green LED
Beeper
Remark
Remark
Initializing/
Power-up
Successful
Connection
Barcode
Scann w/o
Connection
Barcode
Scan w/o
Connection
Successful
Barcode
Scan
Low Power
Power Off
or Standby
Wireless
Disconnection
Unexpected
Barcode
Scan during
Configuration
Charging
Successful
Connection
Full Charge
Unsuccessful
Pincode
Setup
Solid for 2 sec
Flashing
Flashing
Flashing
Flashing
1 Flash
2 Flashes
1 Flash
Solid for 2 sec
Flashing
Flashing
Solid
Solid
4 hours to
fully charge
Power adaptor
needed
See Power Off
Timeout
Scan Pincode
Stop and retry
Scan RESET/
ABORT and retry
See Batch Mode
or Memory Mode
1 long beep
2 beeps
2 beeps
3 beeps
Reads
Configuration
Barcode
Data
Temporarily/
Permanently
Stored
2 short beeps
1 beep
3 short beeps
3 short beeps
3 short beeps
Several short
beeps
5 beeps

CLONING MODE
FORMAT OF CLONING
WHAT IS CLONING MODE?
CLONING duplicates a scanners settings in other scanners. It can
save time when a number of scanners must be programmed to the
same settings.
HOW SHOULD CLONING WORK?
1. Using this guide, make all the necessary settings for one wand.
2. Scan the CLONING MODE bar code shown below.
3. When CLONING MODE is scanned, all setup parameters will be
converted to alphanumeric characters and shown on the monitor.
4. Using a bar code printer, print out all the setup parameters as
Code 39 bar code labels.
5. Scan the printed labels sequentially with each wand to be
programmed.
Figure 1
CLONING MODE
CLONING MODE ON- PC/ AT
.A018$(Cloning Mode on PC/AT) - you can clone the settings to a PC/AT
regardless of the kind of device chosen on the scanner.
NOTES:
1. All cloning strings are upper case.
2. All cloning strings printed on labels should be the same as those on
the monitor sequentially from first to last.
3. Cloning mode works in Word Note Pad only.
4. Never edit the data on the first row (.A017$). It is an entry command
for cloning.
5. The cloning string’s length can be adjusted by combining multiple
strings into one, or by breaking one string into multiple strings starting
from the second row after “....”. Length must be in sequences of four,
such as 4, 8, 12, 16, 20 (MAX).
6. Be sure to print the dots exactly where they are shown on the monitor.
* Format of Cloning:
1st row >>> “.A017$” ( never edit any data of the first row )
2nd row >>> “....XXXX” you can adjust the String’s Length starting
from the dots “....” forward. The length of the string should
be in 4, 8, 12, 16 or 20 ( MAX )digits.
3rd row ~ so on >>> XXXX
End row - A dot “.” Is the ending of cloning.
XXXX Stands for any string
. A016$
. A018$

CORRECT SETTING
WRONG SETTING
EXAMPLE :
1. PROJECT ASSIGNMENTS:
1.1. Beep tone: BEEP LOW -- HIGH.
1.2. Capslock Mode: CAPSLOCK ON.
1.3. Reading Mode: CONTINUOUS AUTO OFF.
2. SETTING PROCEDURE:
2.1. Scan BEEP LOW -- HIGH (GROUP 3).
2.2. Scan CAPSLOCK ON (GROUP 12).
2.3. Scan CONTINUOUS AUTO OFF (GROUP2).
3. All parameters will be converted to alphanumeric characters
and shown on the monitor.
4. Print the results shown on the monitor as bar codes with a bar
code printer. The bar codes should be in the Code 39 symbology.
5. Scan these labels with any of the wands that must be
programmed with the same settings as the first wand. Be sure
to scan from the first row to the second and so on sequentially,
top to bottom.
.A017$
....0604
5A025F04
.
.A017$
....
0604
5A02
5F04
.
4
4
4
4
. (Dot)
.A017$
....06045A02
5F04.
12
4+.(Dot)
. A017$
. . . . 0604
5A025F04.
.A017$
..
..0604
5A02
5F04
.
Wrong Setting: The string “....”
consists of 4 Dots, located at the
beginning of second row; do not
break the “....” into multiple strings.
Wrong Setting: The string lengths of the
second and third row do not match the
length requirements, because rows should
be in length of four digits.
.A017$
....06045
A025F04
.
Wrong Setting because you add
“....” after .A017$:
The .A017$ is a FIXED parameter to
enter setup procedure. It is an unchangeable
parameter. Never add, delete or rearrange
data from the FIRST row.
.A017$....
0604
5A02
5F04.
9 x
7 x
. (Dot)
X
4
4
4+.(Dot)
CLONING MODE

RS-232
Connector
Scanner
Power
Adaptor
Power
Jack
Scanner PS/2
Connector
PS/2
Connector
1. Power down the host computer.
2. Disconnect the keyboard cable from the computer.
3. Connect the “Y ” cable between the keyboard and the scanner and computer.
4. Restart the computer.
5. The scanner will beep.
6. Set the scanner to KEYBOARD interface by referring to GROUP 13
(Interfaces)
7. Scanner will beep to confirm the setting.
8. Scan a bar code to confirm that data shows on the monitor.
HOW TO CONNECT THE SCANNER TO THE
HOST TERMINAL: Handheld Barcode Scanner
KEYBOARD WEDGE INTERFACE
RS-232 INTERFACE
1. Power down the host computer.
2. Disconnect the cable between the scanner and computer.
3. Connect the power adaptor to the cable.
4. Restart the computer,
5. Plug the power adaptor into a power outlet.
6. The scanner will beep.
7. Set the scanner to RS-232 interface by referring to GROUP 13
(Interfaces).
8. Set RS-232 protocol: Baud Rate, Stop Bits, Handshaking, Data Bits
and Parity.
9. Scan a bar code to confirm that data shows on the monitor.
NOTES:
1. Before plugging the power adaptor into the scanner, be sure the voltage, power
consumption, and inner and outer DC characteristics are correct to avoid serious
damage to the scanner and/or the computer.
2. Make sure the protocol communication settings of the scanner (such as baud rate,
data bits, etc.) match those of the host computer. Otherwise, no data will be
transmitted.
Check the power adaptor to ensure:
1. Input of AC current 110V/ 220V matches the power
supply standard of the country in which the scanner
is being used.
2. Adaptor output is +5V DC
3. The jack input is +5V DC

Step 1
Step 2 Step 3
elbaCweNelbaCtneserP
USB
Connector
Scanner
The USB Interface supported is compatible with Apple MAC series,
, Windows 98, 2000, XP, Vista, 7, 8 and so on.
1. Connect the USB cable between the scanner and the computer.
2. The scanner will beep.
3. The scanner will detect the USB driver automatically. (The first time
the scanner is connected via the USB port, follow the appropriate
instructions for the host computer.)
4. Set the scanner to KEYBOARD/USB interface by referring to
GROUP-13 (Interfaces)
5. Scanner will beep to confirm the setting.
6. Scan a bar code to confirm that data shows on the monitor.
USB INTERFACE
HOW TO CHANGE A CABLE
The scanners are designed to switch easily between interface options.
To switch from one interface to another, the appropriate cable must be
installed. To change a cabl, simply follow these steps:
1. To release the cable, insert a pin or straightened paper clip into the
hole at the base of the scanner where the cable is connected.
2. Remove the cable from the scanner.
3. Plug in the new cable.
After changing to a new cable, be sure to reset the interface setting as
appropriate (including parameter settings for the RS-232 interface).

HOW TO SET PARAMETERS
1. Use the scanner to scan at the bar code representing the function/
parameter you want to set.
2. When you hear two beeps, the new settings have been defined or
updated into the memory processor.
Default parameters are indicated in bold type and underlined
characters. The character font is ARIAL BLACK. CD = Check Digit.
CDV = Check Digit Verification.
Most settings require only a single bar code, but a few need several
different bar codes to be scanned in order to completely define a
setting. They are:
How do you program a scanner with this user’s guide?
Preamble / Postamble (maximum 16 digits)
Step 1: Scan CLR PRE/POSTAMBLE.
Step 2: Scan PREAMBLE or POSTAMBLE.
Step 3: Scan any alphanumeric from Full ASCII Table in Group 52-63
Step 4: Scan PREAMBLE or POSTAMBLE.
Min Length / Max Length
Step 1: Scan MIN LENGTH or MAX LENGTH.
Step 2: Scan two digits from Group 60 or Full ASCII numeric table in Appendix
Step 3: Scan MIN LENGTH or MAX LENGTH.
Accuracy Adjustment
Step 1: Scan ACCURACY ADJUSTMENT.
Step 2: Scan one digit from GROUP 5
Step 3: Scan ACCURACY ADJUSTMENT.
Set Code ID (Example: Code 39)
Step 1: Scan CODE 39 SET ID from Group 8
Step 2: Scan either one or two alphanumerics (maximum 2 digits)
from Full ASCII table in Group 54-60
Step 3: Scan CODE 39 SET ID from Group 8
Set A Data - (CX-Codabar, ABC Codabar, Codabar Coupling).
Step 1: Scan SET INSERT DATA.
Step 2: Scan one alphanumeric character from Full ASCII Table in Group 54-60
Step 3: Scan SET INSERT DATA.
1. The scanner will beep three times as a reminder that a setting is
not yet complete.
2. If you make a mistake, forget a step, etc., scan RESET to start again.
NOTES:
. P023$
*.P023$*

SETUP CODE OFF
SETUP CODE ON
. A001$
DEFAULT
GROUP-1
SETUP CODE READ
GENERAL SETTINGS
. A007$
CHECK VERSION
RESET/ ABORT
. P023$
*Reset to factory default
*Check firmware version
*Abort multi-step configuration
*Caution: Scanning SETUP CODE OFF will turn the
scanner into unprogrammable state and the scanner
will not react to any configuration barcode!

If Auto-Sensing Mode(CCD) is on, the
LED will go off if no bar code is detected
after Deactivation Time elapses.
(The default is 3 sec.)
The LED lights automatically when a BAR
CODE is detected.
1. To extend the scanner's life, keep the scanner set to Trigger Mode or
Continuous Auto Off Mode.
2. The LED indicator will glow for GOOD READ.
3. For advanced settings of Auto-Sensing Mode(such as Deactivation Time,
Magnetic Switch and Blue LED) please refer to the next pages.
GENERAL SETTINGS - READING MODE
GROUP-2
CONTINUOUS MODE
. F005$
. F001$
FLASH MODE
. F002$
TRIGGER MODE
CONTINUOUS AUTO OFF
. F006$
TOGGLE MODE
. F003$
. F007$
*AUTO SENSING MODE (CCD)
The LED is always on when the trigger
is pressed.
The LED will go off if one bar code is
read.
The LED is always on when the trigger
is pressed.
The LED will go off if no bar code has
been detected after 60 seconds.
The LED will light when the trigger is
pressed.
The LED will go off when the trigger is
released.
The LED is on steady if a bar code is
close to the scanner, but starts flashing
if no bar code is detected after 60
seconds.
The trigger does not function in Flash
Mode.
LED is always on.
The trigger does not function in
Continuous Mode.
NOTES:
If Auto-Sensing Mode(Laser) is on, the LED
will go off if no barcode is detected after
Deactivation Time elapses.
(The default is 3 sec.)
The laser emits automatically when an
OBJECT is detected.
. F010$
*AUTO SENSING MODE (Laser)

. F017$
BEEP LOW
. F015$
BEEP LOW--HIGH
. F013$
BEEP MEDIUM
. F016$
BEEP HIGH--LOW
. F014$
BEEP HIGH
. D012$
CR
. D013$
CR+LF
. D014$
TAB
. D015$
SPACE
. D010$
NONE
. D016$
ESC
. D011$
LF
.F019$
BEEP HIGH
.F020$
BEEP LOW--HIGH
.F022$
BEEP LOW
BEEP OFF
. F012$
.F021$
BEEP HIGH--LOW
.F018$
BEEP MEDIUM
GROUP-3
GENERAL SETTINGS
BEEP TONE
TERMINATOR
2.7KHz Buzzer
(Wireless Scanner)
2.1KHz Buzzer
(Tethered Scanner)
Below is the position of Terminator among output data string:
[Preamble] [Symbology ID] [Barcode Length] [Barcode Data] [Postamble] [Terminator]
By default, with Preamble, Postamble, Barcode Length and Symbology ID
disabled, the scanner data output will be:
[Barcode Data] [Terminator]
1. For the Keyboard Wedge interface the default terminator is CR.
2. For the USB interface the default terminator is CR.
3. For the RS232 interface the default terminator is CR+LF.
NOTES:

PREAMBLE (16)
. A012$
POSTAMBLE (16)
. A013$
CLEAR PRE/ POSTAMBLE
. A011$
SEND DATA LENGTH ON
.D019$
SEND DATA LENGTH OFF
.D020$
GROUP-4
SEND DATA LENGTH, PREAMBLE & POSTAMBLE.
SEND DATA LENGTH
PREAMBLE & POSTAMBLE ( PREFIX AND SUFFIX )
EXAMPLE:
SETTING PROCEDURE:
DATA FORMAT:
NOTES:
1. A PREAMBLE is a string of up to 16 characters added
to the beginning of a scanned barcode.
2. A POSTAMBLE is a string of up to 16 characters added
to the end of a scanned barcode.
3. Default value for both: None.
[Preamble] [Symbology ID] [Barcode Length] [Barcode Data] [Postamble] [Terminator]
Set PREAMBLE String as “ ## ”
POSTAMBLE String as “ $$ ”
STEP 1 : Scan : CLEAR PRE/ POSTAMBLE.
STEP 2 : Scan : PREAMBLE.
STEP 3 : Scan : “ # ” twice from FULL ASCII Table.
STEP 4 : Scan : PREAMBLE.
STEP 5 : Scan : POSTAMBLE.
STEP 6 : Scan : “ $ ” twice from FULL ASCII Table.
STEP 7 : Scan : POSTAMBLE.

. A010$
0
1
2
3
4
5
6
7
8
9
. P023$
GROUP-5
GENERAL SETTINGS - ACCURACY ADJUSTMENT
NOTES:
1. The scanner will beep three times as reminder that a setting
is not yet complete.
2. If you make a mistake, forget a step, etc., scan RESET to start
again.
ACCURACY
ADJUSTMENT
Accuracy Adjustment assures a more reliable decoded output.
Enabling the feature and setting a number from 1 to 9 subjects
the decoded output a higher standard of accuracy. The higher
the number, the greater the accuracy.
SETTING PROCEDURE:
1. Scan ACCURACY ADJUSTMENT.
2. Scan one digit (1~9) from barcode menu above.
3. Scan ACCURACY ADJUSTMENT.

AIM ID ON
.A014$
FACTORY ID ON
.A008$
SET ID ON
.A015$
.A009$
563987 123453
12411
145287 ]E0
Preamble
145287
CODE ID
AIM ID : ]E0
BARCODE / DATA
EAN 13 +5
OUTPUT
: 145287]E0456398712345312411
[READS POSITIVE BARCODE ONLY]
.D021$
ENABLE INVERSE BARCODE
[READS POSITIVE & NEGATIVE BARCODES]
.D022$
GROUP-6
GENERAL SETTINGS
ENABLE INVERSE BARCODE
ENABLE CODE ID
DISABLE CODE ID
NOTES:
1. Only ONE code ID will be sent.
2. The code ID is located at the position before the bar code data
and after the preamble.
EXAMPLE :
1.Preamble 145287,
2.Code ID: enable AIM ID,
3.Bar code symbologies : EAN 13+5
4
DISABLE INVERSE BARCODE

SYMBOLOGIES CODE ID IDENTIFIER
1. The length of a Code ID is either one or two characters. If one
character is set, the Code ID output will be one character. If two
characters are set, the Code ID output will be two characters.
2. Only one type of Code ID will be sent.
GROUP-7
GENERAL SETTINGS
NOTES:
Steps:
1. Scan the SET ID bar code for a particular symbology.
2. Scan one or two alphanumeric characters from the Full ASCII Table.
3. Scan the SET ID bar code again.
Example: Define the MSI Code ID = A, Code 93 = G9
MSI :
Step1: Scan MSI Set ID (Group 9).
Step2: “A” from Group 56.
Step3: Scan MSI Set ID (Group 9).
Code 93:
Step1: Scan Code 93 Set ID (Group8).
Step2: “G” from Group 56, Scan “9” from Group 60.
Step3: Scan Code 93 Set ID (Group8).
SET ID - SETTING PROCEDURES
Symbologies Factory
ID
AIM ID
(new) Symbologies Factory
ID
AIM ID
(new)
EAN 128
Code 128
EAN8(+2/+5 OFF)
EAN8(+2 ON)
EAN8(+5 ON)
UPC-E(+2/+5 OFF)
UPC-E(+2 ON)
UPC-E(+5 ON)
UPC-A(+2/+5 OFF)
UPC-A(+2 ON)
UPC-A(+5 ON)
EAN-13(+2/+5 OFF)
EAN-13(+2 ON)
EAN-13(+5 ON)
Code 93
Code 11(disable CDV)
Code 11(send one CD)
Code 11(send two CD)
Code 11(not send CD)
Databar
Databar Stacked
Databar Stacked Omnidirectional
Databar Truncated
Telepen(ASCII)
Telepen(Numeric)
J
U
L
F
A
E
S
K
T
]C1
]C0
]E4
]E4
]E4
]E0
]E3
]E3
]E0
]E3
]E3
]E0
]E3
]E3
]G0
]H0
]H0
]H1
]H3
]B0
]B1
MSI
MSI(MOD 10 / CDV & not send CD)
Code 32
Codabar
Codabar(ABC Codabar)
Codabar(CDV & Send CD)
Codabar(CDV & not send CD)
UK Plessey
Matrix 2 of 5
Full ASCII Code 39(disable CDV)
Full ASCII Code 39(CDV & send CD)
Full ASCII Code 39(CDV & not send CD)
Standard Code 39(disable CDV)
Standard Code 39(CDV & send CD)
Standard Code 39(CDV & not send CD)
IATA 2 of 5
detimiLrabataD5fo2lairtsudnI
Databar Expanded
Databar Expanded Stacked
China Post Code
Interleaved 2 of 5(CDV & send CD)
Interleaved 2 of 5(CDV & not send CD)
Interleaved 2 of 5(disable CDV)
O
B
N
P
Y
D
M
G
C
Q
R
V
H
I
]M0
]M1
]X0
]F0
]F1
]F2
]F4
]P0
]X0
]A4
]A5
]A7
]A0
]A1
]A3
0e]0R]
]S0
]X0
PDF417
Z
]E0
]I1
]I3
]I0

. P002$
. P003$
. P004$
. P005$
. P013$
. P007$
. P021$
. P010$
. P016$
. P022$
. P009$
. P011$
. P012$
GROUP-8
GENERAL SETTINGS - SET CODE ID
. P001$
EAN 13 Set ID
EAN 8 Set ID
UPC E Set ID
UPC A Set ID
Code 39 Set ID
Code 93 Set ID
Codabar Set ID
IATA Set ID
Code 128 Set ID
EAN 128 Set ID
Telepen Set ID
Code 11 Set ID
Code 32 Set ID
China Post Code
[TOSHIBA Code] Set ID

. P023$
. P015$
. P014$
. P017$
. P006$
. P018$
. P008$
. P019$
. P020$
. P020$
. P024$
1. The scanner will beep three times as a reminder that a setting is
not yet complete.
2. If you make a mistake, forget a step, etc., scan RESET to start
again.
GROUP-9
GENERAL SETTINGS - SET CODE ID
MSI Code Set ID
UK Plessey Set ID
Matrix 2 of 5 Set ID
Interleaved 2 of 5
Set ID
Industrial 2 of 5 Set ID
Full ASCII Code39
Set ID
GS1 Databar (RSS)
Limited Set ID
GS1 Databar (RSS)
Expanded Set ID
GS1 Databar (RSS)
Set ID
LABEL Code Set ID
[ Reserved ]

GENERAL SETTINGS
GROUP-10
INTERBLOCK DELAY
INTERCHARACTER DELAY
0mS
10mS
50mS
100mS
200mS
500mS
140uS
500uS
1mS
4mS
16mS

GROUP-11
GENERAL SETTINGS
KEYBOARD LAYOUT
. C010$
ENGLISH (USA)
. C018$
ENGLISH (UK)
. C011$
GERMAN
. C012$
FRENCH
. C013$
SPANISH
. C014$
ITALIAN
. C009$
JAPAN (106 key)
CANADIAN
(TRADITIONAL)
. C034$
NORWEGIAN
. C029$
SWEDISH
. C026$
PORTUGUESE
. C031$
CANADIAN (FRENCH)
. C025$
. C016$
SWISS (GERMAN)
. C017$
CZECH (QWERTY)
. C022$
CZECH (QWERTZ)
HUNGARIAN (QWERTZ)
. C021$
. C015$
ALT CODE
HUNGARIAN (101 KEY)
. C024$
SWISS (FRENCH)
. C023$
BRAZILIAN (PORTUGUESE)
. C033$
SLOVAK
. C032$
DANISH
. C027$
DUTCH
. C028$
BELGIAN (AZERTY)
. C030$