IDTECK Star RFL200C User manual

User’s Manual
Proximity Access Controller

2
Table of Contents
1. Important Safety Instructions....................................................................3
2. General.........................................................................................................3
3. Features........................................................................................................4
4. Identifying Supplied Parts..........................................................................4
5. Specification................................................................................................5
6. Installation....................................................................................................6
7. Color Coded & Wiring Table.......................................................................7
8. Wire Connection to Controller...................................................................7
11. Operation..................................................................................................12
12. FCC Registration Information................................................................14
13. Warranty Policy and Limitation of Liability..........................................15
14. How to Make RMARequest (After Sales Service)...............................16

3
1. Important Safety Instructions
When using Proximity Access Controller, basic safety precautions should always be followed to
reduce the risk of fire, electrical shock, and injury to persons. In addition, the following safety guides
should also be followed:
1. Fully read and understand all instructions and follow them completely.
2. Follow all warnings and instructions marked on the product.
3. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. If necessary, use mild soap.
4. Do not use this product near water.
5. Only operate this product using the type of power source indicated. If you are not sure of the type
of power supplied to your installation site, consult your dealer of local power company.
6. Never insert objects of any kind into the product or through the cabinet slots as they maytouch
voltage points and/orshort circuit parts possibly resulting in fire or electric shock.
Never spill liquid of any kind on the product.
7. Never disassemblethis productby yourself; take theunit to a qualified service center whenever
service or repair is required. Opening or removing the covers may expose you to dangerous
voltages or other risks.Also, incorrect reassembly can cause electric shock when the unit is
subsequently used.
8. Unplug this product from the Direct Current (DC) power source and refer to qualified service
personnel under these conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled on the product.
c. If the product does not operate normally after following the operating instructions in this
manual.
Adjust only those controls that are covered by the operating instructions in this manual.
Improper adjustment of other controls that are not covered by this manual may damage the
unit and will often requireextensive work by a qualified technician to restore normal operation.
d. If the product exhibits a distinct change in performance.
2. General
The Star RFL200C / iPASS IP-RFL200Care an elegant looking and an attractive 4"read range
proximity reader built-in Proximity Single Door Access Controller which can be mounted to metal
door frame (mullion) or to any flat wall surface. The Star RFL200C / iPASS IP-RFL200C is epoxy
potted that ensure you a successful operation even in harsh environments.
Two-color LED of green and red, inside Piezo buzzer sound will guarantee you an accurate and
reliable Door Access Operations.

4
3. Features
- 125KHz Standalone ProximityAccess Controller
- iPASS IP-RFL200C:ASK[EM] Format
Star RFL200C: PSK Modulation
- 512 Users
- Network Communication via RS485 (Max.255ch)
TCP/IP (External LAN Converter required, optional)
Wireless (e.g. Bluetooth module required, optional)
- 512 Users/ 256 EventBuffers
- Direct Control of Door Lock
- Power Fail Safe or Power Fail Secure Locks Selectable
- Solid Epoxy Potted
- Waterproof
- Warranty: LifeTime
- Compatible Software: STAR RFL200C
4. Identifying Supplied Parts
Please unpack and check the contents of the box.
Reader Module RFL200C / IP-RFL200C User’s Manual
Bezel
(1ea) (1ea) (1copy)
3.5*40 Screw 3.5*25 Screw Anchor Bolt
(2ea) (2ea) (2ea)

5
5. Specification
Model
RFL200C
IP-RFL200C
CPU
Dual 8bit Microprocessor
Memory
Program
Memory 64KByte Flash ROM
Data Memory
4KByte EEPROM
User
512 Users
Event Buffer
256 Event Buffers
Read Range Passive Type
IDK50 / IMC125:
Up to 2 inch (5cm)
IDC80 / IDC170:
Up to 4 inch (10cm)
IPK50:
Up to 2 inch (5cm)
IPC80 / IPC170:
Up to 4 inch (10cm)
Active Type
IDA150 / IDA200 Compatible
N/A
Reading Time (Card)
30ms
Door Open Time
1~99sec.(Selectable)
Power / Current
DC 12V / Max.150mA
Communication
RS485 (Max.255ch)
Input Port 3ea (Exit Button, Door Sensor,Aux#1)
Output Port
2ea (TR Output / open collector output)
Rating Max 300mAAlarm Output, 1ALock Output
LED Indicator / Beeper
9Array LED Indicators (Red and Green) / Piezo Buzzer
Operating
Temperature
Controller
-35
°
to +60
°
C (-31
°
to +140
°
F)
RF Reader
-35
°
to +65
°
C (-31
°
to +149
°
F)
Operating Humidity
10% to 90% relative humidity non-condensing
Color
Dark Pearl Gray
Material
Polycarbonate
Dimension (W x H x T)
45mm x 124mx 19.64mm (1.8” x 4.9” x 0.8”)
Weight
80g (0.18 lbs)
Warranty
Life Time
Certification
FCC, CE, MIC

6
6. Installation
6-1.Drill one 0.5”(12.7mm) holeat the central of the RFL200C / IP-RFL200C on mullion or wall
mount. Route the cable of reader modulethrough the central hole.
6-2.Drill one 0.39"(10mm) in right horizontal and 1.74"(44.4mm)in upper vertical through the
central hole. And drill the other 0.33"(8.5mm) in lefthorizontaland 1.59”(40.6mm) in under
vertical through the central hole.
6-3. Push reader module on mullion or wall mount then install the main unit using two 6-32 or M3
screws.

7
7. Color Coded & Wiring Table
8. Wire Connection to Controller
SIGNAL
COLOR
Main Power (+12V)
Red
Power Ground (GND)
Black
Aux In 1
Yellow
Door Contact In
Blue
Exit Button In
Green
Alarm Out
Purple
Door Lock Out
White
RS485 (A)
Gray
RS485 (B)
Orange
Not Connect
Brown
* Please cut out tail connector before installation.

8
8-1. Connecting a power supply
- Connect +12V of power supply to Red wire.
- Connect GND of power supply to Black wire.
8-2. Connecting a door lock
- Connect (+) wire of door lock to +12V wire of power supply.
- Connect (-)wire of doorlock to white wire of reader module.
8-3. Connecting an exit button
- ConnectGreen wire ofexit button input to one wire between wiresof exit button.
- Connect GND wire of power supply to the other wire.
8-4. Connecting a door sensor
- Connect COM terminal of door sensor to Blue wire of door sensor input.
- Connect NO terminal of door sensor to GND of power supply.
8-5. Connecting a door lock type
- In a powerfail safe, connect GND wire of power supply to Yellow wire ofdoor locktype input.
- In a powerfail secure, put a floating state onYellow wire of door locktype input.
8-6. RS485 Communication port connection
The INC300 for RS485/RS232 converter is required to connect a product to the PC.
- Connect gray wire for RS485(A) to 485(+) terminal of converter.
- Connect orange wire for RS485(B) to 485(-) terminal of converter.
- Plug 9-pin connector ofconverter into COM Port of the PC.
- Install the application software and then run.
Orange wire
Gray wire
COM Port of the PC
RFL200C /
IP-RFL200C
RS232/RS485 Converter
(ATC)
485 (-)
485 (+)

9
9.
Network connection to the access controller
You can install up to 255 Units of RFL200C / IP-RFL200C.as in the below figure.
- Max. 255 units (Board ID :1~255) canbe installed in a loop.
- Able to connect directly via RS485 or RS232 converter.
485 Converter
RFL200C /
IP-RFL200C
485(-)
Orange wire
485(+)
Gray wire

10
10.
All parameters of Star RFL200C / iPASS IP-RFL200C are set by the application software.
Set up Hardware
10-1 Set up “SystemAddress” and “Normal” or “Toggle Mode”.
①Choose “System Name” and “SystemAddress” on drop down list.
②Click “Normal Mode” or “Toggle Mode”.
③Click “Save” and then “Transmit” button if finishing to step①~②.
10-2 Set “In / Out Point”
①Choose “Door Open Time (sec)” of 1 to 99sec.
②Choose “Lock Type” one whether Power Fail Safe or Power Fail Secure.
③If clicking “Save” button, one dooramong “System (Door)Address” is checked.
④Click “Transmit” button.
SELECT RFL200C
DOOR OPEN TIME (sec)
1~99 (sec)
POWER FAIL SAFE
POWER FAIL SECURE
RFL200C
BOARD ID
DOOR NAME
SYSTEM MODE SELECT

11
10-3 Card Holder Registration or Deletion
- Card Holder Registration or Deletion is performed by the application software.
①Choose “INPUT CARD DATA” and “EMPLOYEE INFORMATION”.
②Click “Save” and then “Transmit” button.
10-4 System Initialization
StarRFL200C / iPASS IP-RFL200C is initialized by the software.
10-5 LED Color Control
The Star RFL200C / iPASS IP-RFL200C can change its LED colorto red orgreen
by the application software.
INPUT CARD DATA
EMPLOYEE INFORMATION
SELECT RFL200C

12
※See “STAR RFL200C”software manual to setup hardware.
11. Operation
11-1. When the RFL200C / IP-RFL200C is powered on,
①All LEDs are lit red or green, then they flash on andoff twice and then turn off.
②Then, red LEDs are lit sequentially frombottom to top.
③The RFL200C / IP-RFL200C beeps once.
11-2. When a registered tag is read on the RFL200C / IP-RFL200C or the exit button is pressed,
①All LEDs switch from red to green, then they turn off sequentially from top to bottom. After
all LEDs are off, they turn on red again.
②The dooropens fora predefinedlength of time andthe first two LEDS fromthe top turn red,
indicating the open status ofthe door.
③The RFL200C / IP-RFL200C beeps once.
11-3. When an unregistered tag is read on the RFL200C / IP-RFL200C,
①All LEDs are lit red, then they flash on and off twice and stay on.
②The RFL200C / IP-RFL200C beeps twice.
11-4. When a tag is read on the RFL200C / IP-RFL200C while the door is open.
①The first two LEDs from the top still stay lit green, indicating the open status of the door.
The rest of the LEDs indicate the authentication status(access granted or denied).
SELECT RFL200C
LED COLOR SELECT

13
11-5. When you need to know the Board ID(or Communication Address),
①Connectthe purple and blue wires together while power is not supplied.
②Apply power and, the first LED flashes on and off either red or green, and the rest of the
LEDs show the Board ID.
③After checking the Board ID,power off the RFL200C / IP-RFL200C and return the purple
and blue wires to their original positions.
④Power on the RFL200C / IP-RFL200Cagain, and it will operate normally again.
Example
11.6 To initialize the RFL200C / IP-RFL200C,
①Power off the RFL200C / IP-RFL200C, and connect the white, green and yellow wires
together.
②Power on the RFL200C / IP-RFL200C, then all LEDs will flash on and off either red or
green and turn off.
③Then, green LEDs are lit sequentially from bottom to top. All LEDs turn green.
④The RFL200C / IP-RFL200C beeps four times, indicating the completion of initialization.
⑤After initialization is finished, return the white,green, and yellow wires to theiroriginal
positions.
⑥Power on the RFL200C / IP-RFL200C again, and it will operate normally again.
11.7 Besides the operations described above, users can register or delete cards using the STAR
RFL200C software, as well. Using this software, you can also adjust orchange “Normal Mode” /
“Toggle Mode”, “Door Open Time” and “LED Color Control”.
※Refer to the “STAR RFL200C” software manualfor more information.
Green / Red LED flashes
Green LED ON (1)
Red LED ON (0)
20=1
21=2
22=4
23=8
24=16
25=32
26=64
27=128
0 * 27= 0
0 * 26= 0
0 * 25= 0
0 * 24= 0
0 * 23 = 0
0 * 22= 0
0 * 21= 0
0 * 20= 0
Board ID = 0
1 * 20= 1
0 * 21= 0
1 * 22= 4
0 * 23 = 0
Board ID =85
1 * 24= 16
0 * 25= 0
1 * 26= 64
0 * 27= 0

14
12. FCC Registration Information
FCC REQUIREMENTS PART 15
Caution: Any changes ormodifications in constructionof this device which are notexpressly
approved by the responsible for compliance could void the user's authority to operate the equipment.
NOTE: This device complies with Part 15 of the FCCRules.
Operation is subject to the following twoconditions;
1. This device may not cause harmful interface, and
2. This device mustaccept any interference received, including interference that may cause undesired
operation.
This equipment hasbeen tested and foundto comply with the limits for a Class A Digital Device,
pursuant to Part 15 of the FCC Rules. These limits are designed to thisequipment generates,uses,
and can radiate radio frequency energyand, if not installed and usedin accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference willnot occur in a particularinstallation. If this
equipment does cause harmfulinterference to radio ortelevision reception, whichcan be determined
by turning the radio or television off and on, theuser is encouraged to try to correct interference by
one or more of the following measures.
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on another circuit.
4. Consult the dealeror anexperienced radio/TV technician for help.

15
13. Warranty Policy and Limitation of Liability
IDTECK warrants this product against defects in material and workmanship for the life of the product
under normal customer use. This Warranty doesn’t apply: 1) to any product which has been dismantled
without authorization of IDTECK or/and has a damaged or detached QC label on itsback side; 2) to any
losses, defects, or damages caused by improper testing, operation, installation, maintenance,
modification, alteration, or adjustment; 3) to any product with a damaged or faded serial number on it; or
4) to any losses, defects, or damages caused by lightning or other electrical discharge, natural disaster,
misuse, accident or neglect.
This Limited Warranty is in lieu of all other warranties, obligations, or liabilities on the part of IDTECK,
and IDTECK DISCLAIMS ANY AND ALL WARRANTY, WHETHER EXPRESS OR IMPLIED, OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.IDTECK does not, and cannot,
know who is present, what property is located, where this product will be used; it would be extremely
difficult to determine the actual damages that may result from a failure of the product to perform as
anticipated; and the low price of this product is based upon the nature of the product provided and the
limited liability that IDTECK assumes. IDTECK IS NOT RESPONSIBLE FOR ANY PERSONAL INJURY,
PROPERTY DAMAGE OR LOSS, DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIALDAMAGES,
OR OTHER LOSS, AND IDTECK’S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
To obtain repair or replacement under the terms of this warranty, visit IDTECK’s Website
(http://www.idteck.com) and place an online RMA request. After an RMA code is issued, return the
productalong withthe authorization RMAcode.
>> Warranty Period
Product Category
Warranty
Period
1 RF CARDS (ACTIVE TYPE) 1 year
FINGERPRINT MODULE / SENSOR
2 RF READERS (WITHOUT EPOXY POTTING)
2 years
3 STANDALONE CONTROLLERS
4 CONTROL PANELS
5 FINGERPRINT READERS
6 RF READERS (WITH EPOXYPOTTING) Lifetime
7 RF CARDS (PASSIVE TYPE)

16
14. How to Make RMA Request (After Sales Service)
To make the RMA request, the product must be initially registered on IDTECK webpage. Please attach
the RMArequestform on the product andsend it to IDTECK RMACenter.
Please follow the instructions below:
1. Please register the RMA request via IDTECK webpage.
: www.idteck.com “Support & Download” “Online RMA” “RMA REQUEST”
(Please refer to the IDTECK webpage for more details.)
2. RMA Code will be issued afterthe RMA Center reviews the RMA request form.
3. Fill out the A/S request form (included in the product package) and attach it to the product using
the aluminum string.
4. Enclose the product along with the RAMCode and send it toIDTECK RMA Center.
(Product without RMA Code is not accepted.)
If you have any questions or problems regarding the RMA services, please contact us using the
following contact information below. Friendly representatives at IDTECK are always standing by to
provide the best after sales services.
IDTECK Headquarter
5F,Ace Techno Tower B/D, 684-1, Deungchon-Dong,
Gangseo-Gu, Seoul, 157-030, Korea
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
Website: www.idteck.com
E-Training Center: http://www.idtecktraining.com
IDTECK Production Facility and RMA Center
3F, 10/10-1/10-2, Dodang-Dong,
Weonmi-Gu, Bucheon-Si, Gyeonggi-Do 420-130, Korea
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
Website: www.idteck.com
E-Training Center: http://www.idtecktraining.com

Mar. 2010 Copyright ©2008 IDTECK Co., Ltd.
The specifications contained in this manual are subject to change without notice at any time.
5F,Ace Techno Tower B/D, 684-1, Deungchon-Dong,
Gangseo-Gu, Seoul, 157-030, Korea
Tel : [phone]
Fax : [phone]
E-mail : [e-mail]