IEI Technology ISP-9652 User manual

1
Socket P Intel® Core™2 Duo MB, GME965/GLE960 with
800/533MHz FSB, VGA, CF, 6 Intel® GbE Lan with Dual
group Lan-Bypass function, USB2.0, SATAII, RoHS
ISP-9652/9602
Quick Installation Guide
Version 1.0
Feb. 22, 2010
Package Contents
ISP-9652/9602 package includes the following items
z1 x ISP-9652/9602 Single Board Computer
z3 x SATA cable
z1 x Mini Jumper Pack
z1 x Utility CD
z1 x QIG(Quick Installation Guide)
©2006 Copyright by IEI Technology corp.
All rights reserved.

2
Specifications
zCPU :
Socket P Intel® Core™ 2 Duo Processor with 800MHz FSB
Socket P Intel® Celeron® M Processor with 533MHz FSB
zSystem Chipset :
Intel® GME965 + ICH8M for ISP-9652
Intel® GLE960 + ICH8M for ISP-9602
zBIOS : AMI Flash BIOS
zFSB :
800 / 533MHz FSB for ISP-9652
533MHz FSB for ISP-9602
zSystem Memory :
Two 240-pins 667/533MHz dual-channel DDR2 SDRAM DIMM
Supported (max. 4GB) for ISP-9652
Two 240-pins 533MHz dual-channel DDR2 SDRAM DIMM Supported
(max. 2GB) for ISP-9602
zEthernet :
LAN1~LAN6: Six Intel® 82574L PCIe GbE Controller(PCIe x1
Interface)
2 x LAN By-Pass Function Gruop(with Relay Control)：
By-Pass Group 1: LAN1/LAN2
By-Pass Group 2: LAN3/LAN4
zI/O Interface :
2 x RS-232 (1 on rear side, 1 on board by pin-header)
10 x USB 2.0 (2 on rear side, 8 on board by pin-header)
3 x SATA II
1 x CF Type II Slot
zDisplay Interface :
CRT/VGA integrated in Intel® GME965/GLE960 (Intel® GMA X3100)
zExpansions :
1 x PCI Slot
1 x PCIe x16 Signal to Golden finger (for ISP-9652 Only)
zSuper I/O : ITE IT8718F

3
zEmbedded Controller: ITE IT8512E
zWatchdog Timer :
Software Programmable support 1~255 sec. System reset by Super
I/O : ITE IT8718F.
zPower Supply : ATX Power Supply
zPower Consumption :
5V@ 12.9 A, 12V@ 0.14A, 12V_Core@ 12.69A, 3.3V@ 0.47A
(Intel® Core™ 2 Duo T7500 2.2GHz with DDR2 800MHz 2GB DRAM
x2)
zOperation Temperature : 0°C ~ 60°C (32°F ~ 140°F)
zOperation Humidity : 5% ~95% non-condensing
zDimensions : 220mm x 244mm
zWeight : GW: 1000g / NW: 450 g
Ordering Information
ISP-9652-R10 :
Socket P Intel® Core™2 Duo MB, GME965 with 800MHz FSB, VGA, CF, 6
Intel® GbE Lan with Dual group Lan-Bypass function, USB2.0, SATAII,
RoHS
ISP-9602-R10 :
Socket P Intel® Core™2 Duo MB, GLE960 with 533MHz FSB, VGA, CF, 6
Intel® GbE Lan with Dual group Lan-Bypass function, USB2.0, SATAII,
RoHS
19800-000114-RS :
RS-232 Cable with Bracket
CB-USB14-RS: Quad Ports USB Cable with Bracket
CB-USB02-RS: Dual Ports USB Cable with Bracket
32100-088600-RS/ 32102-000100-RS/ 32102-000100-200-RS :
SATA Power cable
CF-479B-RS: CPU Cooler

4
Jumpers setting and Connectors
LABEL FUNCTION
J_CMOS1 Clear CMOS jumper
USB_C01 External USB Connector
USB23
USB45
USB67
USB68
Internal USB Connectors
COM1 External Serial Port DB-9 Connector
COM2 Internal Serial Port Connector
VGA1 On Board VGA DB-15 Connector
LAN1
LAN2
LAN3
LAN4
LAN Connectors with Bypass Function
LAN5
LAN6 LAN Connectors without Bypass Function
LAN_LED1 External LAN LED connectors
JEC_SET1 EC Function Setting connector
JSPI2 Flash BIOS/EC FW SPI ROM connector
SATA1
SATA2
SATA3 Serial ATA Connectors
CPU_FAN1
SYS_FAN1 CPU / System Fan Connectors
F_PANEL1 PWR、RST Buttons、Indicators and Speaker
CPU12V1 +12V CPU Power Input Connector
ATX1 ATX Power Input Connector
CF1 Compact Flash Slot
PCI1 PCI Slot
BAT1 Battery connector
DIMM1
DIMM2 DDR2 DIMM Slots

5
J_CMOS1: Clear CMOS Jumper
JP3 DESCRIPTION
1-2
(default) Normal Operation
2-3 Clear CMOS Setup
USB23,USB45,USB67,USB68:
Internal USB Connectors
PIN DESCRIPTION PIN DESCRIPTION
1 VCC(+5V) 2 GND
3 DATA- 4 DATA+
5 DATA+ 6 DATA-
7 GND 8 VCC(+5V)
JSPI2: Flash BIOS/EC FW SPI ROM Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +3.3V 5 GND
2 CS0# 6 CLK
3 SO0 7 SI
4 N/C 8 N/C
COM2 :
Internal Serial Port Connector (RS-232)
PIN DESCRIPTION PIN DESCRIPTION
1 DCD# 6 DSR#
2 RXD 7 RTS#
3 TXD 8 CTS#
4 DTR# 9 VCC(+5V)
5 GND 10 NC

6
CPU12V1:+12V CPU Power Input Connector
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 GND 2 GND
3 +12V 4 +12V
CPU_FAN1,SYS_FAN1:
FAN Connectors
PIN DESCRIPTION
1 GND
2 +12V
3 Rotation Signal
4 Control
BAT1 :
Battery Connector
PIN DESCRIPTION
1 BAT+ (+3.3V)
2 BAT- (GND)
F_PANEL1 : PWR、RST Buttons、Indicators and Speaker
PIN DESCRIPTION PIN DESCRIPTION
1 Power LED+ 2 Speaker+
3 N/C 4 N/C
Power
LED 5 Power LED- 6 N/C
7 PWRBTN+ 8 Speaker-
Speaker
PWRBTN 9 PWRBTN- 10 N/C
11 HDLED+ 12 Reset+
HDDLED 13 HDLED- 14 Reset - RESET

7
JEC_SET1: EC Function Setting Connector
By-Pass Mode/Normal Mode Selection
JEC_SET1(1 – 2)
By-Pass Mode
(Default) Short(Hi)
Normal Mode Open(Low)
JEC_SET1: EC Function Setting Connector
SMBUS ID Selection
JEC_SET1
(3 – 4) JEC_SET1 (5 – 6) JEC_SET1 (7 – 8)
0x60 Open(Low) Open(Low) Open(Low)
0x62 Open(Low) Open(Low) Short(Hi)
0x64 Open(Low) Short(Hi) Open(Low)
0x68 Short(Hi) Open(Low) Open(Low)
0x6A Short(Hi) Open(Low) Short(Hi)
0x6C Short(Hi) Short(Hi) Open(Low)
0x6E
(Default) Short(Hi) Short(Hi) Short(Hi)
System software can send command to Network Bypass MCU through
SMBUS. This jumper selects SMBUS slave address for it.
LAN_LED1: External LAN LED connectors
PIN DESCRIPTION PIN DESCRIPTION
1 CN_L1_LINK_ACT# 14 CN_L1_LED
2 CN_L1_100# 15 CN_L1_1000#
3 CN_L2_LINK_ACT# 16 CN_L2_LED
4 CN_L2_100# 17 CN_L2_1000#
5 CN_L3_LINK_ACT# 18 CN_L3_LED
6 CN_L3_100# 19 CN_L3_1000#
7 CN_L4_LINK_ACT# 20 CN_L4_LED
8 CN_L4_100# 21 CN_L4_1000#
9 CN_L5_LINK_ACT# 22 CN_L5_LED
10 CN_L5_100# 23 CN_L5_1000#
11 CN_L6_LINK_ACT# 24 CN_L6_LED
12 CN_L6_100# 25 CN_L6_1000#
13 N/C 26 N/C

8
JEC_SET1: EC Function Setting Connector
ACK Count
JEC_SET1
(9 – 10) JEC_SET1 (11 – 12) JEC_SET1 (13 – 14) JEC_SET1 (15 – 16)
1 Second Open(Low) Open(Low) Open(Low) Open(Low)
2 Second Open(Low) Open(Low) Open(Low) Short(Hi)
3 Second Open(Low) Open(Low) Short(Hi) Open(Low)
4 Second Open(Low) Open(Low) Short(Hi) Short(Hi)
5 Second Open(Low) Short(Hi) Open(Low) Open(Low)
6 Second Open(Low) Short(Hi) Open(Low) Short(Hi)
… … … … …
16 Second
(Default) Short(Hi) Short(Hi) Short(Hi) Short(Hi)
This jumper sets counting-down interval for SMBUS monitoring.
JEC_SET1: EC Function Setting Connector
HW MCU(EC) Enable/Disable
JEC_SET1(19 – 20)
Enable
(Default) Short(Hi)
Disable Open(Low)

9
LAN Connectors & Bypass Function
•LAN Bypass Definition
LAN Bypass feature removes a single point of failure so that
essential business communication can continue while a
network failure is diagnosed and resolved. In the event of a
power, hardware or software failure, Hardware Bypass will
automatically activate, allowing network traffic to continue.
Traffic between the LAN and WAN is allowed without
interruption.

10