IEI Technology LAN-100G2SF-E810 User manual

LAN-100G2SF-E810
PCIe x16 card with two QSFP28
Quick Installation Guide
Version 1.00
Features
1 x Intel® E810 Ethernet controller
Dual 100GbE QSFP28 connector
PCIe 4.0 x16 interface
RoHS compliant
Packing List
1 x LAN-100G2SF-E810
1 x QIG (Quick Installation Guide)

Specifications
Host Interface
PCIe 4.0 x16
NIC
Intel
®
Ethernet Controller E810-CAM2
External Connector
2 x QSFP28 connector
Speed
100 GbE
Operating Temperature
0°C ~ +40°C (+32°F ~ +104°F)
Storage Temperature
-20°C ~ +75°C (-4°F ~ +167°F)
Operating Humidity
5% ~ 90%, non-condensing
Dimensions
169.54 mm x 56.16 mm x 21.59 mm
Ordering Information
LAN-100G2SF-E810:
Intel® Ethernet Controller E810-CAM2 based PCIe card with two QSFP28 by
PCIe 4.0 x16 interface
Block Diagram

Connector Pinouts
QSFP28 Connectors
Pin
Description
Pin
Description
1 GND (Module ground) 20 GND (Module ground)
2 TX2- (Transmitter inverted data input)21 RX2- (Receiver inverted data output)
3 TX2+ (Transmitter noninverted data input)22 RX2+ (Receiver noninverted data output)
4 GND (Module ground) 23 GND (Module ground)
5 TX4- (Transmitter inverted data input)24 RX4- (Receiver inverted data output)
6 TX4+ (Transmitter noninverted data input)25 RX4+ (Receiver noninverted data output)
7 GND (Module ground) 26 GND (Module ground)
8 MODSEIL (Module select)27
ModPrsL
(Module Present, internal pulled
down to GND)
9 ResetL (Module reset)28
IntL
(Interrupt output, should be pulled up
on host board)
10 VCCRx (+3.3V receiver power supply)29 VCCTx (+3.3V transmitter power supply)
11 SCL (2-wire serial interface clock)30 VCC1 (+3.3V power supply)
12 SDA (2-wire serial interface data)31 LPMode (Low power mode)
13 GND (Module ground) 32 GND (Module ground)
14 RX3+ (Receiver noninverted data output)33 TX3+ (Transmitter noninverted data input)
15 RX3- (Receiver inverted data output)34 TX3- (Transmitter inverted data input)
16 GND (Module ground) 35 GND (Module ground)
17 RX1+ (Receiver noninverted data output)36 TX1+ (Transmitter noninverted data input)
18 RX1- (Receiver inverted data output)37 TX1- (Transmitter inverted data input)
19 GND (Module ground) 38 GND (Module ground)
LAN LED
Description
LAN LED
Description
Speed
(Left)
Green: 100Gbps data rate
Orange: other data rate
Link
(Right) Yellow: Active

Installation
To install the LAN-100G2SF-E810, please follow the steps below.
1. Prepare the computer: Turn off the computer, and remove the power cord from the rear of
the power supply. WARNING: Disconnect the computer from the power supply and from
any networks to which you will install the LAN-100G2SF-E810, or you risk damaging the
system or experiencing electrical shock.
2. Remove the cover from the chassis.
3. Locate available PCIe slots. The LAN-100G2SF-E810 is compatible with PCIe x16 slot.
Remove a blank bracket panel on the back of the computer that aligns with the PCIe slot for
installing the LAN-100G2SF-E810. Save the bracket screw.
4. Align the LAN-100G2SF-E810 to the PCIe slot. Press down gently, but firmly, to seat the
LAN-100G2SF-E810 correctly in the slot. Install the bracket screw to secure it to the
system’s chassis.
5. Replace the cover of the chassis. Reconnect any power cords and any network cables to the
system. Power up the system.
Dimensions (Unit: mm)

Safety Instructions
Warning! To prevent the system from overheating, do not operate it in an area that exceeds
the maximum operating temperature described in the user manual. Ultimate disposal of this
product should be handled according to all national laws and regulations.
IEI Support URL
http://new.ieiworld.com/tw/online_support_form
Product Disposal
According to the requirement of the WEEE legislation the following user information is provided to customers
for all branded IEI Electronics products subject to the WEEE directive.
This symbol on the product or on its packaging indicates that this product must not be disposed of with your
other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over
to a designated collection point for the recycling of waste electrical and electronic equipment. The separate
collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources
and ensure that it is recycled in a manner that protects human health and the environment. For more
information about where you can drop o- your waste equipment for recycling, please contact your local city
office, your household waste disposal service or the shop where you purchased the product.
Headquarters
IEI Integration Corp.
No. 29, ZhongXing Rd., Xizhi Dist.,
New Taipei City 221, Taiwan
TEL: [phone]
FAX: [phone]
[email protected]om
www.ieiworld.com
America
IEI Technology USA Corp.
138 University Parkway, Pomona,
CA 91768, USA
Tel :+ 1-909-595-2819
Fax:[phone]
[email protected]world.com
usa.ieiworld.com
China
IEI Integration (Shanghai) Corp.
No. 515, Shen Fu Rd., Xin Zhuang Industrial Develop Zone,
Shanghai, 201108, China
Tel:[phone]
Fax:[phone]
[email protected]om.cn
www.ieiworld.com.cn
Copyright ©2021 IEI Integration Corp. All rights reserved.