IEI Technology MPCIE-CAN-R10 User manual

MPCIE-CAN
PCIe Mini CAN Bus Card
Quick Installation Guide
Version 1.00 April 26, 2019
Features
Supports dual CAN 2.0B port
USB 2.0 based; no additional driver required
Galvanic isolation 2500 V
Operation temperature: -20°C to 60°C
Packing List
1 x MPCIE-CAN card
2 x CAN-bus cable (3-pin wafer to DB-9)
1 x QIG (Quick Installation Guide)

Specifications
Form Factor
Full-size PCI Express Mini card
Input Interface
PCIe Mini interface (USB interface)
Communication Baud Rate
50/125/250/500/1000K @ 40 meter
Host Site Connector
Internal USB port: Mini PCIe via USB
Output Interface 2 x CAN 2.0B port (with optional isolation)
Connector type: 3-pin male wafer box (p=1.25 mm)
Supported Voltage
5.0 V
Output Connector
DB-9 via 3-pin (1.25 mm) to DB-9 cable (L=150 mm)
LED Indicators
LED1 (green): Power on/off LED
LED2 (red): CAN-1 Tx LED
LED3 (red): CAN-2 Tx LED
Temperature Operation: -20°C ~ +60°C
Storage: -30°C ~ +70°C
OS Support
Windows /Linux
Dimensions (L x W x H)
30 mm x 51 mm x 6 mm
EMI - Complies with EN61000-4-5 2.5kV surge protection
- Complies with IEC 60950-1:2005 + A1: 2009 + A2:2013
2.5kV HiPOT protection
- Complies with EN61000-4-2 (ESD) Air-15kV, Contact-8kV
Ordering Information
MPCIE-CAN-R10:
PCI Express Mini dual CAN bus module, full size, RoHS
32133-026500-100-RS:
CAN bus cable (3-pin wafer to DB-9, 150 mm)

Connector Pinouts
CAN1 & CAN2: CAN bus connector (p=1.25 mm)
Pin
Description
Pin
Description
1 CAN_H 3 GND
2 CAN_L 4 NC
DB-9 connector of CAN bus cable
1 NC 6 NC
2 CAN_L 7 GND
3 CAN_H 8 NC
4 NC 9 NC
5 NC
JSP1: SPI flash connector (p=1.25 mm)
Pin
Description
Pin
Description
1 +VDD 4 TICERST
2 TICEDAT 5 GND
3 TICECLK 6 NC
Dimensions (Unit: mm)

Safety Instructions
Warning! To prevent the system from overheating, do not operate it in an area that exceeds
the maximum operating temperature described in the user manual. Ultimate disposal of this
product should be handled according to all national laws and regulations.
IEI Support URL
http://new.ieiworld.com/tw/online_support_form
Compliance
This equipment has been tested and found to comply with specifications for CE marking. If the user modifies and/or
installs other devices in the equipment, the CE conformity declaration may no longer apply.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
According to the requirement of the WEEE legislation the following user information is provided to customers for all
branded IEI Electronics products subject to the WEEE directive.
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other
household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and electronic equipment. The separate collection
and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure
that it is recycled in a manner that protects human health and the environment. For more information about where
you can drop o- your waste equipment for recycling, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.
Headquarters
IEI Integration Corp.
No. 29, ZhongXing Rd., Xizhi Dist.,
New Taipei City 221, Taiwan
TEL: [phone]
FAX: [phone]
[email protected]om
www.ieiworld.com
America
IEI Technology USA Corp.
138 University Parkway, Pomona,
CA 91768, USA
Tel :[phone]
Fax:[phone]
[email protected]world.com
usa.ieiworld.com
China
IEI Integration (Shanghai) Corp.
No. 515, Shen Fu Rd., Xin Zhuang Industrial Develop Zone,
Shanghai, 201108, China
Tel:[phone]
Fax:[phone]
[email protected]om.cn
www.ieiworld.com.cn
Copyright ©2019 IEI Integration Corp. All rights reserved.