IEI Technology EP-265-910 Mounting instructions

EP-265-910/EP-267-910 Enrich POS System
Page i
EP-265-910/ EP-267-910 Enrich POS System

E-265-910/EP-267-910 Enrich POS System
Page ii
Revision
Date Version Changes
2008-11 1.01 Added current rating of the 12 V output connector and PoweredUSB
connectors
2008-08 1.00 Initial release

EP-265-910/EP-267-910 Enrich POS System
Page iii
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

E-265-910/EP-267-910 Enrich POS System
Page iv
Manual Conventions
WARNING!
Warnings appear where overlooked details may cause damage to the equipment or result
in personal injury. Warnings should be taken seriously. Warnings are easy to recognize.
The word “warning” is written as “WARNING,” both capitalized and bold and is followed by
text. The text is the warning message. A warning message is shown below:
WARNING:
This is an example of a warning message. Failure to adhere to warning
messages may result in permanent damage to the EP series or
personal injury to the user. Please take warning messages seriously.
CAUTION!
Cautionary messages should also be heeded to help reduce the chance of losing data or
damaging the EP series. Cautions are easy to recognize. The word “caution” is written as
“CAUTION,” both capitalized and bold and is followed. The italicized text is the cautionary
message. A caution message is shown below:

EP-265-910/EP-267-910 Enrich POS System
Page v
CAUTION:
This is an example of a caution message. Failure to adhere to cautions
messages may result in permanent damage to the EP series. Please
take caution messages seriously.
NOTE:
These messages inform the reader of essential but non-critical information. These
messages should be read carefully as any directions or instructions contained therein can
help avoid making mistakes. Notes are easy to recognize. The word “note” is written as
“NOTE,” both capitalized and bold and is followed by text. The text is the cautionary
message. A note message is shown below:
NOTE:
This is an example of a note message. Notes should always be read.
Notes contain critical information about the EP series. Please take note
messages seriously.

E-265-910/EP-267-910 Enrich POS System
Page vi
Packing List
NOTE:
If any of the components listed in the checklist below are missing,
please do not proceed with the installation. Contact the IEI reseller or
vendor you purchased the EP series from or contact an IEI sales
representative directly. To contact an IEI sales representative, please
send an email to [email protected].
The items listed below should all be included in the EP-265-910/EP-267-910 series
package.
 1 x EP-265-910/EP-267-910 POS system
 1 x Screw set
 1 x Power cord
 1 x Power supply
 1 x Touch pen
 1 x User Manual and driver CD
Images of the above items are shown in Chapter 3 on page 29.

EP-265-910/EP-267-910 Enrich POS System
Page vii
Table of Contents
1INTRODUCTION..................................................................................................... 1
1.1 EP-265-910/EP-267-910 ENRICH POS OVERVIEW ................................................... 2
1.1.1 Features and Model Variations.......................................................................... 3
1.1.2 Applications ....................................................................................................... 3
1.2 EXTERNAL OVERVIEW ............................................................................................... 4
1.2.1 General Description........................................................................................... 4
1.2.2 Monitor Front Panel.......................................................................................... 4
1.2.3 Monitor Right Side Panel................................................................................... 5
1.2.3.1 I/O Interface Panel...................................................................................... 6
1.2.4 I/O Interface Panel ............................................................................................ 6
1.2.5 Chassis Left Side Panel...................................................................................... 8
1.3 SPECIFICATIONS ......................................................................................................... 8
1.3.1 Preinstalled Hardware Components.................................................................. 8
1.3.2 System Specifications......................................................................................... 9
2DETAILED SPECIFICATIONS ........................................................................... 12
2.1 DIMENSIONS ............................................................................................................ 13
2.1.1 EP-265-910 Dimensions.................................................................................. 13
2.1.2 EP-267-910 Dimensions.................................................................................. 14
2.2 INTEL®CELERON®M PROCESSOR SUPPORT ............................................................ 14
2.3 MOTHERBOARD COMPONENTS................................................................................. 15
2.3.1 Memory Support............................................................................................... 15
2.3.1.1 Installed Memory...................................................................................... 15
2.3.1.2 Additional Memory................................................................................... 15
2.3.2 Storage Capacity.............................................................................................. 16
2.4 EXTERNAL PERIPHERAL INTERFACE CONNECTORS .................................................. 17
2.4.1 Serial Port Connectors .................................................................................... 17
2.4.2 LAN Connectivity............................................................................................. 18
2.4.3 External USB Connectors................................................................................ 19
2.4.3.1 Standard USB Connectors ........................................................................ 19
2.4.3.2 PoweredUSB Connectors.......................................................................... 20

E-265-910/EP-267-910 Enrich POS System
Page viii
2.4.4 Keyboard and Mouse Connectivity.................................................................. 21
2.5 EP-265-910/EP-267-910 FRONT SIDE..................................................................... 21
2.5.1 Monitor ............................................................................................................ 21
2.5.2 Touch-Screen Module....................................................................................... 22
2.6 GRAPHICS ................................................................................................................ 22
2.6.1 Intel®910GMLE Integrated Graphics Media Accelerator 900....................... 22
2.6.2 Dual-Display.................................................................................................... 22
2.7 AUDIO...................................................................................................................... 23
2.7.1 High Definition Audio Controller.................................................................... 23
2.7.2 Stereo Speakers................................................................................................ 23
2.8 SYSTEM POWER ....................................................................................................... 23
2.8.1 Power Mode..................................................................................................... 23
2.8.1.1 AT Power Mode ........................................................................................ 24
2.8.1.2 ATX Power Mode ..................................................................................... 24
2.8.2 Power Supply................................................................................................... 24
2.8.3 Power Connectors............................................................................................ 24
2.8.3.1 Power Input Connector............................................................................. 25
2.8.3.2 Power Output Connector........................................................................... 25
2.8.4 RJ-12 Connectors for Cash Drawer Power..................................................... 25
2.9 WIRELESS ETHERNET............................................................................................... 26
2.10 THERMAL MANAGEMENT....................................................................................... 26
3UNPACKING.......................................................................................................... 27
3.1 UNPACKING.............................................................................................................. 28
3.1.1 Packing List ..................................................................................................... 29
4INSTALLATION .................................................................................................... 30
4.1 ANTI-STATIC PRECAUTIONS...................................................................................... 31
4.2 INSTALLATION PRECAUTIONS................................................................................... 31
4.3 PREINSTALLED COMPONENTS .................................................................................. 32
4.4 INSTALLATION AND CONFIGURATION STEPS............................................................. 32
4.5 REMOVE THE BOTTOM PANELS ................................................................................ 33
4.6 CF CARD INSTALLATION.......................................................................................... 34
4.7 HDD INSTALLATION ................................................................................................ 35
4.8 JUMPER SETTINGS.................................................................................................... 37

EP-265-910/EP-267-910 Enrich POS System
Page ix
4.8.1 Access the Jumpers.......................................................................................... 38
4.8.2 Preconfigured Jumpers.................................................................................... 40
4.8.3 Cash Drawer Voltage Select ............................................................................ 40
4.8.4 CF Voltage Select............................................................................................. 41
4.8.5 Clear CMOS Jumper........................................................................................ 42
4.8.6 COM3, COM4 and COM5 Pin 9 Select........................................................... 44
4.9 MOUNTING THE SECOND DISPLAY (OPTIONAL)........................................................ 45
4.10 BOTTOM PANEL SWITCH AND CONNECTORS .......................................................... 47
4.10.1 AT/ATX Mode Selection................................................................................. 47
4.10.2 LAN Connection............................................................................................. 47
4.10.3 Serial Device Connection .............................................................................. 48
4.10.4 USB Device Connection................................................................................. 49
4.10.5 Parallel Device Connection........................................................................... 50
5SYSTEM MAINTENANCE .................................................................................. 52
5.1 SYSTEM MAINTENANCE INTRODUCTION.................................................................. 53
5.2 ANTI-STATIC PRECAUTIONS...................................................................................... 53
5.3 TURN OFF THE POWER.............................................................................................. 54
5.4 REPLACING COMPONENTS ....................................................................................... 54
5.4.1 Hard Disk Drive Replacement......................................................................... 54
5.4.2 CF Card Replacement...................................................................................... 54
5.4.3 DIMM Module Replacement............................................................................ 55
5.4.4 Wireless Module Replacement ......................................................................... 56
5.4.5 Motherboard Replacement............................................................................... 57
6AMI BIOS SETUP.................................................................................................. 58
6.1 INTRODUCTION ........................................................................................................ 59
6.1.1 Starting Setup................................................................................................... 59
6.1.2 Using Setup...................................................................................................... 59
6.1.3 Getting Help..................................................................................................... 60
6.1.4 Unable to Reboot After Configuration Changes.............................................. 60
6.1.5 BIOS Menu Bar................................................................................................ 60
6.2 MAIN ....................................................................................................................... 61
6.3 ADVANCED............................................................................................................... 62
6.3.1 CPU Configuration.......................................................................................... 63

E-265-910/EP-267-910 Enrich POS System
Page x
6.3.2 IDE Configuration........................................................................................... 64
6.3.2.1 IDE Master, IDE Slave ............................................................................. 66
6.3.3 Super IO Configuration.................................................................................... 72
6.3.4 Hardware Health Configuration...................................................................... 76
6.3.5 Remote Access Configuration.......................................................................... 81
6.3.6 USB Configuration........................................................................................... 83
6.4 PCI/PNP .................................................................................................................. 85
6.5 BOOT ....................................................................................................................... 88
6.5.1 Boot Settings Configuration............................................................................. 88
6.5.2 Boot Device Priority........................................................................................ 91
6.6 SECURITY................................................................................................................. 91
6.7 CHIPSET ................................................................................................................... 93
6.7.1 Northbridge Chipset Configuration................................................................. 93
6.7.2 Southbridge Configuration .............................................................................. 96
6.8 POWER..................................................................................................................... 97
6.8.1 Advanced Power Configuration....................................................................... 98
6.9 EXIT....................................................................................................................... 100
7SYSTEM MONITORING.................................................................................... 102
7.1 IEI INTELLIGENT SYSTEM MANAGEMENT MODULE (ISMM)................................. 103
7.1.1 What is iSMM................................................................................................. 103
7.1.2 iSMM Features............................................................................................... 103
7.2 COM PORT LED INDICATORS................................................................................ 104
ASYSTEM SPECIFICATIONS ............................................................................. 105
7.3 MOTHERBOARD SPECIFICATIONS ........................................................................... 106
A.1 PROCESSOR SPECIFICATIONS................................................................................. 106
A.2 SCREEN SPECIFICATIONS ....................................................................................... 107
A.3 TOUCH SCREEN SPECIFICATIONS........................................................................... 108
A.4 WIRELESS MODULE .............................................................................................. 108
A.5 POWER SUPPLY MODULE ...................................................................................... 109
BEXTERNAL CONNECTOR PINOUTS..............................................................111
B.1 INTRODUCTION.......................................................................................................112
B.2 RJ-12 CASH DRAWER CONNECTOR........................................................................112
B.3 POWER INPUT CONNECTOR ....................................................................................112