iHome Control SMARTPLUG iSP100 User manual

Intelligent Home Solutions
Model: iSP100
Control your SmartPlug from anywhere with your smartphone
SMARTPLUG
Quick Start Guide
Quick Start Guide
WHAT YOU’LL NEED
Apple®device running iOS 9.3 or later or Android device running KitKat 4.4 or later connected
to your preferred WiFi network
WiFi network transmitting at 2.4GHz1
NOTE: If you intend to use a mix of devices (iOS AND Android), please set up
the SmartPlug using your iOS device and then share to your Android device(s).
back
(blank)
Model: iSP100 QSG (English)
Size: 153mm x 92mm
Date : Sep 29,2017
Pages: 12
Version: 2

Quick Start Setup
Download and open the iHome Control app from the App Store or Google Play.
Plug the SmartPlug into a desired outlet*. The LED will start blinking to indicate
it is ready for setup.
Tap Add Device ... in the Devices tab and follow the on-screen directions to
complete setup.
When prompted, scan or type the Accessory Setup Code below:
Success! You should now be able to toggle your SmartPlugs ON or OFF from the
iHome Control app or by using Siri®.
* When used outdoors, must be plugged into GFCI outlet ONLY.
1
2
3
4
5
NOTE: When typing, dashes are not required
1

Sharing
Now that you’ve successfully completed setup, you may want to gain/share access
to your SmartPlugs on dierent devices. Please follow the chart below:
Grant Access to iOS Devices
NOTE: sharing works from iOS to iOS, iOS to Android, and Android to Android
w/ dierent
iCloud accounts
w/ the same
iCloud account
Download and
launch the iHome
Control app on other
device(s) and wait
for the SmartPlug(s)
to appear
NOTE: If you chose
to set up an iHome
account, use the
same login on both
devices
Tap Sharing in the
Settings section
of the iHome
Control app and
follow instructions
Download and
launch the iHome
Control app on
other devices(s)
Accept invitation on
other device(s)
Grant Access to Android Devices
option 2option 1
Download and
launch the iHome
Control app on
other device(s)
and sign in with
your existing
iHome account
credentials
Tap Sharing in
the Settings
section of the
iHome Control
app and follow
instructions
Download and
launch the iHome
Control app on
other device(s)
Accept invitation
on other device(s)
2

The iSP100 SmartPlug is a Wi-Fi enabled device that allows wireless control of lamps,
heaters, fans and other small appliances up to 1800 Watts general use.2
Plug Overview
Press once to toggle SmartPlug ON or OFF
Press and hold for 15 seconds to reset the
SmartPlug to factory settings
(Use the iHome Control app to reconfigure network settings)
Lights up when SmartPlug is ON and
electricity is flowing through
Flashing Green: SmartPlug is searching for
a Wi-Fi network
Solid Green: SmartPlug is connected to
a Wi-Fi network
Flashing Red: SmartPlug is disconnected
from a Wi-Fi network
Button
Wi-Fi Status Indicator
Power Indicator
Mounting Tab
3

4
Mounting your iSP100 (optional)
Choose a mounting placement that positions the bottom of your iSP100 at least 2ft
from the ground.
Mark the area behind the center of the mounting tab with a pencil. Move the iSP100
away from the wall for the next step.
Install the screw into the wall using an appropriate tool. Leave around ¼” of the screw
exposed from the wall.
Place the mounting hole of the iSP100 over the screw and allow it to hang. Do not
over-tighten.
*The supply cord of this control can be replaced only by the manufacturer or his
accredited service agent
1
2
3
4
A screw has been provided for your convenience. If you choose to mount your
iSP100 SmartPlug on an exterior wall we recommend following these steps:
Mounting
Tab

HomeKit also enables control of your SmartPlug with your voice, using Siri. Here are
some examples of how to execute commands successfully. Activate Siri and say:
HomeKit is an Apple standard for home control. HomeKit allows you to group
together several devices into Homes, Rooms, and Zones.
Establish Zones — a collection of rooms (e.g. “First Floor”)
Create Scenes —a collection of on-demand device triggers (e.g. a
“Bedtime” Scene can be set to turn ON a Fan and turn OFF a Lamp)
Siri (iOS only)
Zones
Scenes
“Turn ON
my Living Room”
“Turn OFF my
Bedroom Lamp”
“Set Bedtime
Scene”
This command will turn ON
all SmartPlugs assigned to
a particular room, in this
case, the Living Room.
This command turns OFF
a particular SmartPlug.
For example, if you have
an accessory named
“Lamp” in your Bedroom.
This command will execute
your Bedroom Scene if set
up in the Scenes tab of
your iHome Control app.
5
HomeKit™ (iOS only)

Ways to Use Your SmartPlug
Rules
6
Create Rules — think of a rule as a schedule or trigger
For example, create a rule named “Nighttime.” This will
turn a flood light ON at 5:00 pm and OFF at 11:00 pm. It can
be set to repeat every day or for specific days that you choose.
Nightime
Every day at 5:00 PM

3rd Party Connections
Your iHome Smart Plug works with the following leading platform partners to extend
your smart home integration:
7
SmartPlugs integrates with your Wink app and other Wink enabled
products. No hub required!
Works with your Nest “Home” and “Away” status to automatically
turn your SmartPlug on or off.
Just ask Alexa to control your SmartPlug from any Alexa enabled device.
Use your voice to control Smart Plugs with any Google Assistant
enabled device.

8
Electrical Ratings
120V Volts AC, 60Hz
15A General use
1800W Resistive
960W Tungsten
500 VA Electronic Ballast
Safety Warnings
Electric Shock Can Kill or Cause Serious Injury
Be safe and take necessary precautions when handling the Smartplug, including:
Plug directly into grounded 3-prong electrical outlet only (DO NOT plug into an extension cord)
DO NOT exceed the recommended electrical ratings
When using outdoors, use only with ground fault circuit interrupter (GFCI) outlet
When plugged into grounded 3-prong outlet, always ensure that the housing is facing downwards,
and is at least 2 feet o the ground. Use the plug’s mounting tag to hang from a screw to ensure
correct orientation
DO NOT use in wet or damp areas
DO NOT expose to heavy rain or immerse in water or any other liquid.
Remove Smartplug from outlet before cleaning
DO NOT clean with liquid
DO NOT remove ground pin (middle pin) or use with 3- to 2-prong adaptor
DO NOT use with devices that should not be operated unattended, such as power tools
DO NOT use in precision timing applications where inaccurate timing could be dangerous
(sunlamps, saunas, etc.)
Keep children away from SmartPlug and outlet
No Serviceable parts inside. DO NOT open or tamper with unit.
Recommendations
Test device locally for safe operation before attempting to control it remotely
DO NOT use with an outlet controlled by a wall switch as the switch may be o

Notices
9FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
To assure continued FCC compliance:
1. Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to
operate the equipment.
2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.
FEDERAL COMMUNICATIONS COMMISSION
INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Indoor/Outdoor Use:

10
1All Wi-Fi routers support 2.4GHz spectrum. If your router was deliberately set to only transmit 5GHz, then please
note that the SmartPlug will not work properly on your network. Enterprise networks (such as in colleges and
businesses) often have more restricted security settings that may impact the performance of your SmartPlug.
2Your SmartPlug supports devices or appliances up to 1800 Watts for general use. Please consult the owner’s manual
of your device.
Notes
For warranty information: visit https://www.ihomeaudio.com/support/
IC
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator and your body.
Cet appareil radio est conforme au CNR-247d’Industrie Canada. L’utilisation de ce dispositif est autorisée seulement aux deux
conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit être prêt à accepter tout
brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Legal
Use of the Works with Apple HomeKit logo means that an electronic accessory has been designed to connect specifically to iPod
touch®, iPhone®, or iPad®, respectively, and has been certified by the developer to meet Apple performance standards. Apple is
not responsible for the operation of this device or its compliance with safety and regulatory standards.
Controlling this HomeKit-enabled accessory automatically and away from home requires an Apple TV® with tvOS 10.1 or later or
an iPad with iOS 10.1 or later set up as a home hub.
Wink is a registered trademark. Nest®, Nest Learning Thermostat and the Works with Nest logos are trademarks licensed by Nest
Labs, Inc. Amazon Echo and Amazon Alexa are trademarks of Amazon.com, Inc. or its aliates.
CAN ICES-(B)/NMB-3(B)

Questions?
1.800.288.2792
www.ihome.com
iSP100_2017_QSG_v12