iHome iSPR4 QSG User manual

A
B
A
B
C
Intelligent Home Solutions
Model: iSPR4
Quick Start Guide
Open the iHome Control app
and tap the “ ” beside the
SmartPlug you want to pair
Scroll down and tap:
initiate remote control pairing
Choose any of the four remote
buttons you want to pair
Press the ON button five times
Press the OFF button. If the
SmartPlug turns o, pairing was
successful. If not, repeat from step
i
Questions?
1.800.288.2792
www.ihome.com
FRONT
Remove plastic pull tab from battery
door before proceeding
Remote control setup requires an iSP6
or iSP8 SmartPlug connected to WiFi
Keep remote control within 15 ft. of
SmartPlug during pairing
Enable Pairing Mode on SmartPlug
ON OFF
START HERE
1
Send Pairing Commands
Send Remote Pairing Command
2
1
Quick Start Guide
Model: iSPR4 QSG (English)
Size: 65mm x 155mm
Date : Mar 1 , 2016
Pages: 1
Helpful Facts

iSPR_2016_QSG_v5
For warranty information: visit
https://www.ihomeaudio.com/support/
BACK
Helpful Facts
Notices
FCC
This device complies with Part 15 of the FCC Rules.Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may causeundesired
operation.
To assure continued FCC compliance:
1. Any changesor modifications not expresslyapproved approved by the grantee
of this device could void the user's authority to operate the equipment.
2. This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
FEDERAL COMMUNICATIONS COMMISSION
INTERFERENCE STATEMENT
This equipmenthasbeen tested and found to comply with thelimits for a Class B
digital device, pursuant to Part15 of the FCC Rules. Theselimits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radiofrequency energy
and, if not installed and used in accordance with theinstructions, may cause harmful
interference to radio communications. However, there isno guarantee that
interference will not occur in a particular installation.If thisequipment does cause
harmful interference to radio or television reception, which can bedetermined by
interference by oneormore of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipmentand receiver.
which the receiver is connected.
- Consult the dealer oran experienced radio/TV technician for help.
IC
© 2016 SDI Technologies, Inc. All rights reserved
Questions? Visit www.ihome.com
or call1-800-288-2792 Toll Free
Multiple SmartPlugs can beprogrammed to use the
same remote control button. This allows a group of
plugs to be triggered at the sametimewith a single
press (allplugsmust be within range of remote control).
The SmartPlug will retain remote control pairing
information even through power outagesand software
resets. Pleaseuse the iHome Control app to delete
remote control pairing info.
The LED at the top ofthe remote will blink green when
a button ispressed. If the SmartPlug does not respond,
please move within range. If problem persists,please
replace the battery and retry.
Each SmartPlug can bepaired to a maximum of 4
individualbuttons.
Le present appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation estautorisée aux deux
conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectrique subi,
mêmesi le brouillage est susceptible d'en compromettre le fonctionnement.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.