IKEA RENODLAD User manual

RENODLAD GB
DE

ENGLISH
Please refer to the last page of this manual for the full list of
IKEA appointed After Sales Service Provider and relative
national phone numbers.
DEUTSCH
Auf der letzten Seite dieser Broschüre nden Sie eine
vollständige Liste der oziellen IKEA After-Sales-Dienstleister
mit den jeweiligen nationalen Telefonnummern.

ENGLISH 4
DEUTSCH 32

Contents
Safety information 4
Safety instructions 6
Product description 8
Control panel 9
Programme selection 10
Basic settings 12
Before rst use 16
Daily use 18
Hints and tips 20
Care and cleaning 22
Troubleshooting 24
Technical information 29
Environmental concerns 29
IKEA guarantee 29
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible
for any injuries or damage that are the result of incorrect
installation or usage. Always keep the instructions in a safe
and accessible location for future reference.
Children and vulnerable people safety
•This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
•Children between 3 and 8 years of age and persons with
very extensive and complex disabilities shall be kept away
from the appliance unless continuously supervised.
•Children of less than 3 years of age should be kept away
from the appliance unless continuously supervised.
•Children should be supervised to ensure that they do not
play with the appliance.
•Keep detergents away from children.
ENGLISH 4

•Keep children and pets away from the appliance when the
door is open.
•Children shall not carry out cleaning and user maintenance
of the appliance without supervision.
General Safety
•This appliance is intended to be used in household and
similar applications such as:
–farm houses; sta kitchen areas in shops, oces and
other working environments;
–by clients in hotels, motels, bed & breakfast and other
residential type environments.
•Do not change the specication of this appliance.
•The operating water pressure (minimum and maximum)
must be between 0.5 (0.05) / 10 (1.0) bar (MPa)
•Follow the maximum number of 13 place settings.
•If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualied persons in order to avoid a hazard.
•WARNING: Knives and other utensils with sharp points must
be loaded in the basket with their points down or placed in a
horizontal position.
•Do not leave the appliance with the open door unattended
to avoid stepping accidentally onto it.
•Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
•Do not use high pressure water sprays and/or steam to
clean the appliance.
•If the appliance has ventilation openings in the base, they
must not be covered e.g. by a carpet.
•The appliance is to be connected to the water mains using
the new supplied hose-sets. Old hose sets must not be
reused.
ENGLISH 5

Safety instructions
Installation
Warning! Only a qualied person
must install this appliance.
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Do not use the appliance before installing
it in the built-in structure due to safety
manner.
• Follow the installation instructions
supplied with the appliance.
• Always take care when moving the
appliance as it is heavy. Always use safety
gloves and enclosed footwear.
• Do not install or use the appliance where
the temperature is less than 0 °C.
• Install the appliance in a safe and suitable
place that meets installation
requirements.
Electrical connection
Warning! Risk of re and electric
shock.
• Warning: this appliance is designed to be
installed / connected to a grounding
connection in the building.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable.
Should the mains cable need to be
replaced, this must be carried out by our
Authorised Service Centre.
• Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
• This appliance is tted with a 13 A mains
plug. If it is necessary to change the
mains plug fuse, use only a 13 A ASTA (BS
1362) fuse (UK and Ireland only).
Water connection
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not
used for a long time, where repair work
has been carried out or new devices tted
(water meters, etc.), let the water ow
until it is clean and clear.
• Ensure that there are no visible water
leaks during and after the rst use of the
appliance.
• The water inlet hose has a safety valve
and a sheath with an inner mains cable.
Warning! Dangerous voltage.
• If the water inlet hose is damaged,
immediately close the water tap and
disconnect the mains plug from the
mains socket. Contact the Authorised
Service Centre to replace the water inlet
hose.
Use
• Do not put ammable products or items
that are wet with ammable products in,
near or on the appliance.
• Dishwasher detergents are dangerous.
Follow the safety instructions on the
detergent packaging.
• Do not drink and play with the water in
the appliance.
ENGLISH 6

• Do not remove the dishes from the
appliance until the programme is
complete. Some detergent may remain
on the dishes.
• Do not store items or apply pressure on
the open door of the appliance.
• The appliance can release hot steam if
you open the door while a programme
operates.
Service
• To repair the appliance contact the
Authorised Service Centre. Use original
spare parts only.
• Please note that self-repair or non-
professional repair can have safety
consequences and might void the
guarantee.
• The following spare parts will be available
for 7 years after the model has been
discontinued: motor, circulation and drain
pump, heaters and heating elements,
including heat pumps, piping and related
equipment including hoses, valves, lters
and aquastops, structural and interior
parts related to door assemblies, printed
circuit boards, electronic displays,
pressure switches, thermostats and
sensors, software and rmware including
reset software. Please note that some of
these spare parts are only available to
professional repairers, and that not all
spare parts are relevant for all models.
• The following spare parts will be available
for 10 years after the model has been
discontinued: door hinge and seals, other
seals, spray arms, drain lters, interior
racks and plastic peripherals such as
baskets and lids.
• Concerning the lamp(s) inside this
product and spare part lamps sold
separately: These lamps are intended to
withstand extreme physical conditions in
household appliances, such as
temperature, vibration, humidity, or are
intended to signal information about the
operational status of the appliance. They
are not intended to be used in other
applications and are not suitable for
household room illumination.
Disposal
Warning! Risk of injury or
suocation.
• Disconnect the appliance from the mains
supply.
• Cut o the mains cable and discard it.
• Remove the door catch to prevent
children and pets to get closed in the
appliance.
ENGLISH 7

Product description
456
10
9
1
3
2
78
1Lower spray arm
2Filters
3Rating plate
4Salt container
5Rinse aid dispenser
6Detergent dispenser
7Cutlery basket
8Lower basket
9Upper spray arm
10 Upper basket
The graphics is a general
overview. For more details, refer
to other chapters or documents
provided with the appliance.
Beam-on-Floor
Beam-on-Floor is a light displayed on the
oor below the appliance door.
• When a programme starts, a white light is
on and stays on for the duration of the
programme.
• When the programme is completed, the
white light is o.
• When the appliance has a malfunction,
the white light ashes.
Beam-on-Floor is o when the
appliance is deactivated.
ENGLISH 8

Control panel
1 3 4 5 62
1On/O button / Reset button
2Delay start button
3Display
4Programme buttons
5Option buttons
6AUTO programme button
Display
A AB
A. Indicators
B. Time indicator
Indicators
Indicator Description
Rinse aid indicator. It is on when
the rinse aid dispenser needs re‐
lling. Refer to "Before rst
use".
Indicator Description
Salt indicator. It is on when the
salt container needs relling. Re‐
fer to "Before rst use".
Machine Care indicator. It is on
when the appliance needs inter‐
nal cleaning with the Machine
Care programme. Refer to "Care
and cleaning".
Drying phase indicator. It is on
when a programme with the dry‐
ing phase is selected. It ashes
when the drying phase operates.
Refer to "Programme selec‐
tion".
ENGLISH 9

Programme selection
Programmes
A B C D E
A. • Quick 30' is the shortest programme
suitable for dishwashing a load with
fresh and light soil.
• Rinse & Hold is a programme for
rinsing o food remains from the
dishes. It prevents odours forming in
the appliance. Do not use detergent
with this programme.
B. 60 Minutes is a programme suitable for
dishwashing a load with fresh and lightly
dried-on soil.
C. 90 Minutes is a programme suitable for
dishwashing and drying normally soiled
items.
D. Intensive is a programme suitable for
dishwashing and drying heavily soiled
items.
E. ECO is the longest programme oering
the most ecient use of energy and
water consumption for crockery and
cutlery with normal soil. This is the
standard programme for test
institutes. 1)
AUTO
The AUTO programme automatically adjusts
the dishwashing cycle to the type of load.
The appliance senses the degree of soil and
the amount of dishes in the baskets. It
adjusts the temperature and quantity of
water as well as the wash duration.
Options
You can adjust the programme selection to
your needs by activating options.
Power Clean
Power Clean improves the dishwashing
results of the selected programme. The
option increases the wash temperature and
duration.
Gentle / Glass
Gentle / Glass prevents delicate load,
glassware in particular, from damaging. The
option prevents rapid changes in the
dishwashing temperature of the selected
programme and reduces it to 45 °C.
Programmes overview
Programme Dishwasher
load
Degree of soil Programme phases Options
Crockery, cut‐
lery
Fresh • Dishwashing 50 °C
• Intermediate rinse
• Final rinse 45 °C
• AutoOpen
•
•
All All degrees of
soil
• Prewash Not applicable
1) This programme is used to assess compliance with the Ecodesign Comission Regulation (EU) 2019/2022.
ENGLISH 10

Programme Dishwasher
load
Degree of soil Programme phases Options
Crockery, cut‐
lery
Fresh, lightly
dried-on
• Dishwashing 60 °C
• Intermediate rinse
• Final rinse 50 °C
• AutoOpen
•
•
Crockery, cut‐
lery, pots,
pans
Normal, lightly
dried-on
• Dishwashing 60 °C
• Intermediate rinse
• Final rinse 55 °C
• Drying
• AutoOpen
•
•
Crockery, cut‐
lery, pots,
pans
Normal to
heavy, dried-on
• Prewash
• Dishwashing 60 °C
• Intermediate rinse
• Final rinse 60 °C
• Drying
• AutoOpen
•
•
Crockery, cut‐
lery, pots,
pans
Normal, lightly
dried-on
• Prewash
• Dishwashing 50 °C
• Intermediate rinse
• Final rinse 55 °C
• Drying
• AutoOpen
•
•
Crockery, cut‐
lery, pots,
pans
All degrees of
soil
• Prewash
• Dishwashing 50 -
60 °C
• Intermediate rinse
• Final rinse 60 °C
• Drying
• AutoOpen
Not applicable
Machine Care For cleaning the appliance in‐
terior. Refer to "Care and
Cleaning".
• Cleaning 70 °C
• Intermediate rinse
• Final rinse
• AutoOpen
Not applicable
Consumption values
Programme 1) 2) Water (l) Energy (kWh) Duration (min)
9.4 -11.4 0.57 - 0.69 30
3.7 - 4.5 0.02 - 0.05 15
ENGLISH 11

Programme 1) 2) Water (l) Energy (kWh) Duration (min)
9.3 - 11.4 0.82 - 0.94 60
9.1 - 11.1 1.01 - 1.13 90
9.2 - 11.2 0.96 - 1.08 160
9.9 0.835 240
8.2 - 11.2 0.67 - 1.08 120 - 170
Machine Care 8.4 - 10.2 0.60 - 0.71 60
1) The pressure and the temperature of the water, the variations of the mains supply, the options, the quantity of
dishes and the degree of soil can change the values.
2) The values for programmes other than ECO are indicative only.
Information for test institutes
To receive the necessary information for
conducting performance tests (e.g.
according to: EN60436 ), send an email to:
[email protected]
In your request, include the product number
code (PNC) from the rating plate.
For any other questions regarding your
dishwasher, refer to the service book
provided with your appliance.
Basic settings
You can congure the appliance by changing
basic settings according to your needs.
Number Setting Values Factory
setting Description1)
1Water hardness 1L - 10L 5L Adjust the level of the water softener
according to the water hardness in
your area.
2Rinse aid empty
notication
1d (on) / 0d
(o)
1d Activate or deactivate the rinse aid indi‐
cator.
3End sound 1b (on) / 0b
(o)
0b Activate or deactivate the acoustic sig‐
nal for the end of a programme.
4Auto door open 1o (on) / 0o
(o)
1o Activate or deactivate the AutoOpen.
ENGLISH 12

Number Setting Values Factory
setting Description1)
5Key tones 1F (on) / 0F
(o)
1F Activate or deactivate the sound of the
buttons when pressed.
6Latest pro‐
gramme selec‐
tion
1H (on) /
0H (o)
0H Enable or disable the automatic selec‐
tion of the most recently used pro‐
gramme and options.
1) For more details, refer to the information provided in this chapter.
You can change the basic settings in setting
mode. Instructions on how to congure the
appliance are provided further in this
chapter.
When the appliance is in setting mode, the
display shows a digit and a letter. For each
setting, a dedicated letter is displayed. The
dedicated letters are indicated in the table.
The order of the basic settings presented in
the table is also the order of the settings in
setting mode.
The water softener
The water softener removes minerals from
the water supply, which would have a
negative eect on the washing results and
on the appliance.
The higher the content of these minerals,
the harder your water is. Water hardness is
measured in equivalent scales.
The water softener should be adjusted
according to the hardness of the water in
your area. Your local water authority can
advise you on the hardness of the water in
your area. Set the right level of the water
softener to assure good washing results.
Water hardness
German degrees
(°dH)
French degrees
(°fH)
mmol/l Clarke de‐
grees
Water softener level
47 - 50 84 - 90 8.4 - 9.0 58 - 63 10
43 - 46 76 - 83 7.6 - 8.3 53 - 57 9
37 - 42 65 - 75 6.5 - 7.5 46 - 52 8
29 - 36 51 - 64 5.1 - 6.4 36 - 45 7
23 - 28 40 - 50 4.0 - 5.0 28 - 35 6
19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1)
15 - 18 26 - 32 2.6 - 3.2 18 - 22 4
11 - 14 19 - 25 1.9 - 2.5 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 5 - 12 2
ENGLISH 13

German degrees
(°dH)
French degrees
(°fH)
mmol/l Clarke de‐
grees
Water softener level
<4 <7 <0.7 < 5 1 2)
1) Factory setting.
2) Do not use salt at this level.
Regardless of the type of detergent used,
set the proper water hardness level to
keep the salt rell indicator active.
Multi-tabs containing salt are not
eective enough to soften hard
water.
Regeneration process
For the correct water softener operation, the
resin of the softener device needs to be
regenerated regularly. This process is
automatic and is the part of the normal
dishwasher operation.
When the prescribed quantity of water (see
values in the table) has been used since the
previous regeneration process, a new
regeneration process will be initiated
between the nal rinse and the programme
end.
Water softener level Amount of water (l)
1 250
2 100
3 62
4 47
5 25
6 17
7 10
8 5
9 3
10 3
In case of the high water softener setting, it
may occur also in the middle of the
programme, before the rinse (twice during a
programme). Regeneration initiation has no
impact on the cycle duration, unless it occurs
in the middle of a programme or at the end
of a programme with a short drying phase.
In such cases, the regeneration prolongs the
total duration of a programme by additional
5 minutes.
Subsequently, the rinsing of the water
softener that lasts 5 minutes may begin in
the same cycle or at the beginning of the
next programme. This activity increases the
total water consumption of a programme by
additional 4 litres and the total energy
consumption of a programme by additional
2 Wh. The rinsing of the softener ends with a
complete drain.
Each performed softener rinse (possible
more than one in the same cycle) may
prolong the programme duration by another
5 minutes when it occurs at any point at the
beginning or in the middle of a programme.
All the consumption values
mentioned in this section are
determined in line with the
currently applicable standard in
laboratory conditions with water
hardness 2.5mmol/L (water
softener: level 3) according to the
regulation: 2019/2022 .
The pressure and the
temperature of water as well as
the variations of the mains supply
can change the values.
The rinse aid empty notication
The rinse aid helps to dry the dishes without
streaks and stains. It is automatically
released during the nal rinse.
ENGLISH 14

When the rinse aid chamber is empty, the
rinse aid indicator turns on. If the drying
results are satisfactory while using multi-
tablets only, you can deactivate the
notication for relling the rinse aid.
However, for best drying performance,
always use rinse aid.
If standard detergent or multi-tablets
without rinse aid are used, activate the
notication to keep the rinse aid rell
indicator active.
End sound
You can activate an acoustic signal that
sounds when the programme is completed.
Acoustic signals sound also when
a malfunction of the appliance
occurs. It is not possible to
deactivate these signals.
AutoOpen
AutoOpen improves the drying results with
less energy consumption. The appliance
door opens automatically during the drying
phase and remains ajar.
AutoOpen is automatically activated with all
programmes other than Rinse & Hold.
Caution! Do not try to close the
appliance door within 2 minutes
after automatic opening. This can
cause damage to the appliance.
Caution! If children, pets or
people with disabilities have
access to the appliance,
deactivate AutoOpen. The
automatic opening of the door
may pose a danger and expose
possible hazards inside the
appliance (such as knives, sharp
objects, chemicals).
When AutoOpen opens the door,
Beam-on-Floor might not be
completely visible. To see if the
programme is complete, look at
the control panel.
Key tones
The buttons on the control panel make a
click sound when you press them. You can
deactivate this sound.
Latest programme selection
You can set the automatic selection of the
most recently used programme and options.
The latest programme that was completed
before the appliance deactivation is saved. It
is then selected automatically after you
activate the appliance.
When the latest programme selection is
disabled, the default programme is ECO.
Setting mode
How to enter setting mode
You can enter setting mode before starting a
programme. You cannot enter setting mode
while the programme is running.
To enter setting mode, press and hold
simultaneously and for about 3
seconds.
• The lights related to , and
are on.
• The display shows the current value
of the rst available setting.
ENGLISH 15

How to navigate in setting mode
You can navigate in setting mode using
programme buttons.
A B C
A. Previous button
B. OK button
C. Next button
Use Previous and Next to switch between
the basic settings and to change their value.
Use OK to enter the selected setting and to
conrm changing its value.
How to change a setting
Make sure the appliance is in setting mode.
1. Use Previous or Next to select the
desired setting.
The display shows the current setting value
(a digit and the dedicated letter).
2. Press OK to enter the setting.
The current setting value ashes.
3. Press Previous or Next to change the
value.
4. Press OK to conrm the setting.
• The new setting is saved.
• The appliance returns to the basic
settings list.
5. Press and hold simultaneously and
for about 3 seconds to exit
setting mode.
The appliance returns to the programme
selection.
The saved settings remain valid until you
change them again.
Before rst use
1. Make sure that the current level of the
water softener agrees with the
hardness of the water supply. If not,
adjust the level of the water softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start the programme Quick 30' to
remove any residuals from the
manufacturing process. Do not use
detergent and do not put dishes in the
baskets.
After starting the programme, the appliance
recharges the resin in the water softener for
up to 5 minutes. The washing phase starts
only after this procedure is complete. The
procedure is repeated periodically.
The salt container
Caution! Use rough salt designed
for dishwashers only. Fine salt
increases the risk of corrosion.
The salt is used to recharge the resin in the
water softener and to assure good washing
results in daily use.
ENGLISH 16

Filling the salt container
1 2
3
Put 1 litre of water in
the salt container
(only for the rst
time).
4
Put 1 kg of salt in the
salt container.
5
Turn the cap of the
salt container
clockwise to close
the salt container.
Caution! Water and salt may
come out of the salt container
when you ll it. After you ll the
salt container, immediately start a
programme to prevent corrosion.
Filling the rinse aid dispenser
1 2
3
max
4
5
M
A
X
4
3
2
1
To adjust the
released quantity of
rinse aid, turn the
selector between
position 1 (lowest
quantity) and
position 4 (highest
quantity).
ENGLISH 17

Daily use
1. Open the water tap.
2. Press and hold until the appliance is
activated.
3. Fill the salt container if it is empty.
4. Fill the rinse aid dispenser if it is empty.
5. Load the baskets.
6. Add the detergent.
7. Select and start a programme.
8. Close the water tap when the
programme is complete.
Using the detergent
1 2
3
A
Put the detergent or
the multi-tablet in
compartment (A).
4
If the programme has a prewash phase, put
a small quantity of detergent on the inner
part of the appliance door.
When you use multi-tablets that contain salt
and rinse aid, it is not necessary to ll the
salt container and the rinse aid dispenser.
• Adjust the water softener to the lowest
level.
• Set the rinse aid dispenser to the lowest
position.
Multi-tabs containing salt are not
eective enough to soften hard
water.
How to select and start a programme
1. Press the button dedicated to the
programme you want to set.
• The light related to the button is on.
• The display shows the programme
duration.
2. Activate applicable options if desired.
3. Close the appliance door to start the
programme.
How to select and start the
programme
1. To select , press and hold for 3
seconds.
• The light related to the button is on.
• The display shows the programme
duration.
Options are not applicable to this
programme.
2. Close the appliance door to start the
programme.
How to activate options
1. Select a programme.
ENGLISH 18

2. Press the button dedicated to the option
you want to activate.
• The light related to the button is on.
• The display shows the updated
programme duration.
By default, options must be
activated every time before you
start a programme.
If the latest programme selection
is enabled, the saved options are
activated automatically along with
the programme.
It is not possible to activate or
deactivate options while a
programme is running.
Not all options are compatible
with each other.
Activating options often increases
the water and energy
consumption as well as the
programme duration.
How to select and start the
programme AUTO
1. Press .
• The light related to the button is on.
• The display shows the programme
duration.
2. Close the appliance door to start the
programme.
The appliance senses the type of load and
adjusts a suitable wash cycle. During the
cycle, the sensors operate several times and
the initial programme duration can
decrease.
How to delay the start of a
programme
1. Select a programme.
2. Press repeatedly until the display
shows the desired delay time (from 1 to
24 hours).
The light related to the button is on.
3. Close the appliance door to start the
countdown.
During the countdown, it is not possible to
change the delay time and the programme
selection.
When the countdown is complete, the
programme starts.
How to cancel the delay start while
the countdown operates
Press and hold for about 3 seconds.
The appliance returns to the programme
selection.
If you cancel the delay start, you
have to select the programme
again.
How to cancel a running programme
Press and hold for about 3 seconds.
The appliance returns to the programme
selection.
Make sure that there is detergent
in the detergent dispenser before
you start a new programme.
Opening the door while the
appliance operates
Opening the door while a programme is
running stops the appliance. It may aect
the energy consumption and the
programme duration. After closing the door,
the appliance continues from the point of
interruption.
If the door is opened for more
than 30 seconds during the
drying phase, the running
programme ends. It does not
happen if the door is opened by
AutoOpen function.
The Auto O function
This function saves energy by switching the
appliance o when it is not operating.
ENGLISH 19

The function activates automatically:
• After up to 15 seconds once the
programme is complete.
• After 5 minutes if a programme was not
started.
End of the programme
When the programme is complete, the
display shows 0:00.
The Auto O function switches the appliance
o automatically.
All buttons are inactive except for the on/o
button.
Hints and tips
General
Follow the hints below to ensure optimal
cleaning and drying results in daily use and
to protect the environment.
• Washing dishes in the dishwasher as
instructed in the user manual usually
consumes less water and energy than
washing dishes by hand.
• Load the dishwasher to its full capacity to
save water and energy. For best cleaning
results, arrange items in the baskets as
instructed in the user manual and do not
overload the baskets.
• Do not pre-rinse dishes by hand. It
increases the water and energy
consumption. When needed, select a
programme with a prewash phase.
• Remove larger residues of food from the
dishes and empty cups and glasses
before putting them inside the appliance.
• Soak or slightly scour cookware with
rmly cooked-on or baked-on food before
washing it in the appliance.
• Make sure that items in the baskets do
not touch or cover each other. Only then
can the water completely reach and wash
the dishes.
• You can use dishwasher detergent, rinse
aid and salt separately or you can use the
multi-tablets (e.g. ''All in 1''). Follow the
instructions on the packaging.
• Select a programme according to the type
of load and the degree of soil. ECO oers
the most ecient use of water and
energy consumption.
• To prevent limescale buildup inside the
appliance:
–Rell the salt container whenever
necessary.
– Use the recommended dosage of the
detergent and rinse aid.
– Make sure that the current level of
the water softener agrees with the
hardness of the water supply.
– Follow the instructions in the chapter
"Care and cleaning".
Using salt, rinse aid and detergent
• Only use salt, rinse aid and detergent
designed for dishwasher. Other products
can cause damage to the appliance.
• In areas with hard and very hard water,
we recommend to use basic dishwasher
detergent (powder, gel, tablets containing
no additional agents), rinse aid and salt
separately for optimal cleaning and
drying results.
• Detergent tablets do not fully dissolve
with short programmes. To prevent
detergent residues on the tableware, we
recommend that you use tablets with
long programmes.
• Always use the correct quantity of
detergent. Insucient dosage of
detergent can result in poor cleaning
results and hard-water lming or spotting
on the items. Using too much detergent
with soft or softened water results in
detergent residues on the dishes. Adjust
the amount of detergent based on the
ENGLISH 20