IKEA Livsgnista User manual

LIVSGNISTA
ES
PT
GB
IT
GB IT ES PT GR IE
GR

ENGLISH 4
ITALIANO 19
ESPAÑOL 35
PORTUGUÊS 51
ΕΛΛΗΝΙΚΑ 67
GB
IT
ES
PT
GR
IE
 Language,Lingua,Idioma,Idioma,Γλώσσα
 Country,Paese,País,País,Χώρα

ENGLISH 4
Your safety and the safety of
others are very important.
This manual and the appliance
itself provide important safety
messages, to be read and
observed at all times.
This is the safety alert
symbol, pertaining to safety,
which alerts users to potential
hazards to themselves and
others.
All safety messages will follow
the safety alert symbol and
either the terms:
DANGER Indicates a
hazardous situation which, if
not avoided, will cause serious
injury.
WARNING Indicates a
hazardous situation which, if
not avoided, could cause serious
injury.
All Safety messages will tell you
what the potential hazard is, tell
you how to reduce the chance of
injury, and tell you what
can happen if the instructions are
not followed.
The appliance must be
disconnected from the power
supply before carrying out any
installation work.
Installation and maintenance
must be carried out by a
qualiedtechnician,in
compliance with the
manufacturer’s instructions and
local safety regulations to the
relevant gas standard. Only use
original spare parts. Do not
repair or replace any part of the
applianceunlessspecically
stated in the user manual.
WARNING If the information
in this manual is not followed
exactly,areorexplosionmay
result causing property damage
or injury.
- Do not store or use gasoline or
otherammablevaporsand
liquids in the vicinity of this
appliance.
What to do if you smell gas:
- Do not try to light any
appliance.
- Do not touch any electrical
switch.
- Do not use any phone in your
building.
- Immediately call your gas
Safety Information 4
Productdescription 7
Dailyuse 7
Helpful hints and tips 8
Maintenance and cleaning 8
What to do if ... 9
Injector table 10
Technical data 11
Installation 11
Environmentalconcerns 16
IKEAGUARANTEE 17
Safety Information
Table of contents

ENGLISH 5
supplier from a neighbor’s
phone. Follow the gas
supplier’s instructions.
- If you cannot reach your
gassupplier,callthere
department.
- Installation and service must
beperformedbyaqualied
installer, service agency or the
gas supplier.
- Use appliance in well
ventilated rooms only.
- The electrical and gas
connections must comply with
local regulations.
- When the hob is installed,
provide a multi-pole circuit
breaker with a contact
separation of at least 3
mm, that provides full
disconnection.
- Regulations require that the
appliance is grounded.
- The power cable must be long
enough for connecting the
appliance,oncettedinits
housing, to the power supply
- Useonlyexibleorrigidmetal
hose for gas connection.
- If necessary, the electrical
power cable must be
replaced exclusively with a
power cable having identical
characteristics to the original
supplied by manufacturer
(type H05V2V2-F 90°C or
H05RR-F). This operation must
beperformedbyaqualied
electrician.
- The manufacturer cannot
be held responsible for any
injury to persons or animals or
damage to property arising
from failure to comply with
these requirements.
- Do not use multiple plug
adapters or extension cords.
- Do not pull the power cable
to disconnect it from the
electrical supply.
- The electrical components
must not be accessible to the
user after installation.
- Do not touch the appliance
with any wet part of the body
and do not operate it when
barefoot.
- This hob (class 3) is designed
solely for private household
use for cooking food. Do not
use this appliance as a space
heater to heat or warm the
room. Doing so may result in
carbon monoxide poisoning
and overheating of the hob.
- The Manufacturer declines
all responsibility for
inappropriate use or incorrect
setting of the controls.
- The appliance and its
accessible parts become
hot during use. Care should
be taken to avoid touching
heating elements. Children less
than 8 years of age shall be
kept away unless continuously

ENGLISH 6
supervised. This appliance
can be used by children aged
from 8 years and above and
persons with reduced physical,
sensory or mental capabilities
or lack of experience and
knowledge if they have
been given supervision or
instruction concerning use of
the appliance in a safe way
and understand the hazards
involved. They shall not play
with the appliance.
- The use of a gas appliance
produces heat and humidity in
the room. Make sure the room
is well-ventilated, or install an
extractor hood with exhaust
duct.
- Domestic animals should be
kept away from the appliance.
- In case of prolonged use,
additional ventilation may
be necessary (by opening
a window or increasing the
hood extraction speed).
- After use, make sure the knobs
are in off position and close
the main gas supply cock or
the gas cylinder valve.
- Overheated oils and fats
catchreeasily.Always
remain vigilant when cooking
foods rich in fat, oil or alcohol
(e.g. rum, cognac, wine).
- Unattended cooking on a
hob with fat or oil can be
dangerous and may result in
re.NEVERtrytoextinguisha
rewithwater,butswitchoff
the appliance and then cover
amee.g.withalidorare
blanket.
Dangerofre:donotstore
items on the cooking surfaces.
- Keep the packaging materials
out of the reach of children.
- Before cleaning or
maintenance wait for hob to
cool down.
- CAUTION: “In case of hotplate
glass breakage:
- shut immediately off all
burners and any electrical
heating element and isolate
the appliance from the power
supply
- do not touch the appliance
surface,
- do not use the appliance”.
- These instructions are valid
only for those countries whose
symbol is shown on the rating
plate (under cooktop).
- This product is not intended
to be installed and operated
outdoors.
Save these instructions

ENGLISH 7
Product description
1Removable grates
2Rapid burner
3Auxiliary burner
4Semi-rapid burners
5Front left rapid burner control knob
6Rear left semi-rapid burner control knob
7Rear right semi-rapid burner control knob
8Front right auxiliary burner control knob
1
2
3
7 8
4
5 6
1
4
Important: When the hob area is hot do not
spill liquids to avoid glass damages.
Donotlettheburnerameextend
beyond the edge of the pan.
Important: when the hob is in use, the entire
hob area may become hot.
- To ignite one of the burners, turn the
relative knob anti-clockwise to the
maximumamesetting.
- Press the knob against the control panel
to ignite the burner.
- After the burner has ignited, keep the
knob pressed for about 5-10 seconds to
allow proper device operation.
This burner safety device shuts off the gas
supplytotheburneriftheamegoesout
accidentally (because of sudden draught, an
interruption in the gas delivery, boiling over
of liquids, etc.).
- The knob must not be pressed for
more than 15 sec. If, after that time has
elapsed, the burner does not remain lit,
wait at least one minute before trying to
light it again.
NOTE: should particular local conditions
of the delivered gas make the ignition of
burnerdifcult,itisadvisabletorepeat
the operation with the knob turned to small
amesetting.Theburnermightgooutwhen
the knob is released. This means that the
safety device has not warmed up enough. In
this case, repeat the operations described
above.
Daily use
Symbols
Solid disc Tap closed
Largeame Maximumame
Smallame Minimumame

ENGLISH 8
This hob has burners of different diameters.
For better burner performance, please stick
to the following rules:
- Use pots and pans with bottoms the
same width as that of the burners or
slightly larger (see table on the right).
- Onlyuseat-bottomedpotsandpans.
- Use the correct amount of water
for cooking foods and keep the pot
covered.
- Make sure pots on the grates do not
protrude beyond the edge of the hob.
IMPORTANT: improper use of the grids can
result in damage to the hob: do not position
the grids upside down or slide them across
the hob. Do not use:
- Cast iron griddles, ollar stones,
terracotta pots and pans.
- Heat diffusers such as metal mesh, or
any other types.
- Two burners simultaneously for one
receptacle(e.g.shkettle).
Disconnect power before servicing.
- All the enamelled and glass parts
should be cleaned with warm water and
neutral solution.
- Stainless steel surfaces may be stained
by calcareous water or aggressive
detergents if left in contact for too long.
Any food spills (water, sauce, coffee, etc.)
should be wiped away before they dry.
- Clean with warm water and neutral
detergent, and then dry with a soft
cloth or chamois. Remove baked-on dirt
withspeciccleanersforstainlesssteel
surfaces.
NOTE: Clean glass and enamelled parts
only with soft cloth or sponge.
- Do not use abrasive or corrosive
products, chlorine-based cleaners or
pan scourers.
- Do not use steam cleaning appliances.
- Donotuseammableproducts.
- Do not leave acid or alkaline substances,
such as vinegar, mustard, salt, sugar or
lemon juice on the hob.
CLEANING THE HOB PARTS
- Grids, burner caps and burners can be
removed to be cleaned. Do not wash
them in the dishwasher.
- Clean them by hand with warm water
and non-abrasive detergent, removing
any food residues and checking that
none of the burner openings is clogged.
- Rinse and dry
- Retburnersandburnercapscorrectly
in the respective housings.
- When replacing the grids, make sure
that the panstand area is aligned with
the burner.
- Models equipped with electrical
ignition plugs and safety device require
thorough cleaning of the plug end in
order to ensure correct operation.
Helpful hints and tips
Maintenance and cleaning
Burner Pot Ø
Rapid from 24 to 26 cm
Semi-rapid from 16 to 22 cm
Auxiliary from 8 to 14 cm

ENGLISH 9
Problem Possible cause Solution
The electric ignition does not
work
There is no electrical
supply
Check the unit is plugged in
and the electrical supply is
switched on.
The burner fails to ignite The gas tap could be
closed
Check that the gas tap is
open
The gas ring burns unevenly Burner crown may
be occluded by food
residues
Clean the burner crown
according to cleaning
instructions to make sure that
the burner crown is clear of
food residues.
What to do if ...
Before calling the After-Sales Service:
1. Check “Troubleshooting guide” to see if
you can eliminate the problem yourself
2. Turn the hob on again to check if correct
operation has been restored.
3. If the problem persists, contact the After-
sales Service.
Give the following information:
• type of fault;
• hob model;
• service number (i.e. the number after the
word SERVICE on the dataplate under
thehobandonthewarrantycerticate);
• your full address;
• your telephone number.
If any repairs are required, contact an
authorised service centre, indicated in the
warranty.
Failure to comply with these instructions
may compromise the safety and quality of
the product.
Check these items frequently, and if
necessary, clean them with a damp cloth.
Any baked-on food should be removed
with a toothpick or needle.
NOTE: to avoid damaging the electric
ignition device, do not use it when the
burners are not in their housing.

ENGLISH 10
Type of gas used Type of
burner
Injector
marking
Nominal
heating
capacity
kW
Nominal
consum-
ption
Reduced
heat
capacity
kW
Gas pressure
(mbar)
min. nom. max.
NATURAL GAS
(Methane)
G20
rapid
semi-rapid
semi-rapid
auxiliary
125 A
104 B
104 B
78 A
3,00
2,00
2,00
1,00
286 l/h
190 l/h
190 l/h
95 l/h
0,60
0,35
0,35
0,30
17 20 25
LIQUEFIED
PETROLEUM GAS
(Butane) G30
rapid
semi-rapid
semi-rapid
auxiliary
85 A
69
69
50
3,00
2,00
2,00
1,00
218 g/h
145 g/h
145 g/h
73 g/h
0,60
0,35
0,35
0,30
20 28
30 35
LIQUEFIED
PETROLEUM GAS
(Propane) G31
rapid
semi-rapid
semi-rapid
auxiliary
85 A
69
69
50
3,00
2,00
2,00
1,00
214 g/h
143 g/h
143 g/h
71 g/h
0,60
0,35
0,35
0,30
25 37 45
Injector table
Category II2H3+
Type of gas
used
4 burners
60cm
Nominal heating
capacity kW
Total nominal
consumption
Air necessary
(m3) for
combustion
1 m3of gas
G20 20 mbar 1R - 2 SR (2kW) -
1 AUX 8,00 761 l/h 9,52
G30 28-30 mbar 1R - 2 SR (2kW) -
1 AUX 8,00 581 g/h 30,94
G31 37 mbar 1R - 2 SR (2kW) -
1 AUX 8,00 571 g/h 23,80
ElectricPower:220-240V~50/60/Hz

ENGLISH 11
Technical data
Dimensions
Width (mm) 590
Height (mm) 44
Length (mm) 510
Voltage (V) 220-240 V ~
The technical information are situated in the
rating plate on the bottom side of the appliance.
Installation
Use protective gloves for handling,
preparing and installing the product.
After unpacking the hob, make sure that it
has not been damaged during transport. In
the event of problems, contact the dealer or
your nearest After-sales Service.
Technical information for the installer
- This product can be embedded in a
worktop 20 to 60 mm thick.
- If there is no oven beneath the hob,
insert a separator panel that has a
surface at least equal to the opening
in the work surface. This panel must be
positioned at a maximum distance of
150 mm below the upper surface of the
work surface but, in no case less than 20
mm from the bottom of the hob.
- Before installation, make sure that:
- the local gas delivery conditions (nature
and pressure) are compatible with the
settings of the hob (see the rating plate
and injector table);
- the outer surfaces of the furniture or
appliances adjacent to the hob are heat
resistant according to local regulations;
- This appliance is not connected to a
fume exhaust device. It shall be installed
in accordance with current installation
regulations. Particular attention shall
be given to the relevant requirement
regarding ventilation.
- Combustion products are discharged
outdoorsthroughspecichoodsorwall
and/or window mounted electrical fans.
Gas connection
This operation must be performed by a
qualiedtechnician.
The gas supply system must comply with
local regulations to the relavant gas
standard.
- Youcanndspeciclocalregulationsfor
some countries in the paragraph
- “Reference to Local Regulations”. If no
information concerning your Country is

ENGLISH 12
given,pleaseaskdetailstoaqualied
technician.
- The connection of the hob to the gas
pipe network or gas cylinder must be
made by means of a rigid copper or
steelpipewithttingscomplyingwith
local regulations, or by means of a
continuous-surface stainless steel hose
complying with local regulations. The
maximum length of the hose is 2 linear
metres.
A
B
C
C
D
D
- Connect elbow (A)* or (B)* supplied with
to the hob inlet main pipe and interpose
the washer (C) supplied, in compliance
with EN 549.
- Use elbow (A) for France and elbow (B)
for all other destinations.
-IMPORTANT: if a stainless steel hose
is used, it must be installed so as not to
touch any mobile part of the furniture.
It must pass through an area where
there are no obstructions and where it is
possible to inspect it on all its length.
- After connection to the gas supply, check
for leaks with soapy water. Light up the
burners and turn the knobs from max
position to minimum position to
checkamestability
Electrical connection
WARNING
- This operation must be performed by a
qualiedtechnician.
- The electrical connections must comply
with local regulations.
- The earthing of this appliance is
compulsory by law.
L
N
Earth
(yellow/green)
- Do not use an extension cord.
-IMPORTANT: the data relevant to the
voltage and power absorption are
indicated on the rating plate.
Assembly
Use protective gloves for cleaning the
product perimeter surface, then apply
the supplied gasket to the hob.
After having cleaned the perimeter surface,
apply the supplied gasket to the hob.
Position the hob in the worktop opening
made respecting the dimensions indicated
in the Instruction.
NOTE: the power supply cable must be long
enough to permit its upward extraction.
To secure the hob, use the brackets provided
with it. Fit the brackets into the relevant
bores shown by the arrow and fasten them
by means of their screws in accordance with
the thickness of the worktop.
Make sure that the outlet is near the product
to install. So, if the cable that came with the
product is not long enough, you will need to

ENGLISH 13
replace it with another one having the same
features but with the right length.
Adjustment to different type of gas
WARNING
- This operation must be performed by a
qualiedtechnician.
If the appliance is intended to operate with
a different gas from the gas type stated on
the rating plate and information label on
the top of the hob, change the injectors.
Remove the information label and keep it
with the instructions booklet.
Use pressure regulators suitable for the gas
pressure indicated in the Instruction.
- The gas injectors must be changed
byAfterSalesServiceoraqualied
technician.
- Injectors not supplied with the appliance
must be ordered from After Sales
Service.
- Adjust the minimum setting of the taps.
NOTE: when liquid petroleum gas is used
(G30/G31), the minimum gas setting screw
must be tightened as far as it will go.
IMPORTANT: should you experience
difcultyinturningtheburnersknobs,
please contact the After Sales Service for
the replacement of the burner tap if found to
be faulty.
IMPORTANT: when gas cylinder is adopted,
the gas cylinder or gas container must be
properly settled (vertical orientation).
Replacing the injectors (see paragraph
“injector table”)
- Remove grids (A).
- Extract burners (B).
- Using a socket spanner of the
appropriate size unscrew the injector
(C), unscrew the injector to be replaced.
- Replace it with the injector suitable for
the new type of gas.
- Re-assemble the injector in (D).
Beforeinstallingthehob,remembertoafx
the gas calibration plate supplied with
the injectors in such a way that it covers
the existing information relating to gas
calibration.
Replacement of the gas injector
Adjusting minimum gas setting of taps
To ensure that the minimum setting is
correctly adjusted, remove the knob (E) and
proceed as follows:

ENGLISH 14
- tightenscrewtoreducetheameheight
(-);
- loosenscrewtoincreasetheameheight
(+).
The adjustment must be performed with the
tap in minimum gas setting position (small
ame).
- The primary air of the burners does not
need to be adjusted.
- At this stage, light up the burners and
turn the knobs from max position to
minimum position tocheckame
stability.
Upon completion of adjustment, reseal
the work surface using sealing wax or an
equivalent material.
GB REFERENCE TO LOCAL
REGULATIONS
Provision for ventilation
The room in which the appliance is installed
must have an air supply to current B.S. 5440
- Part 2 standards.
All rooms require a permanent vent in
addition to the openable window.
If there are other fuel burning appliances in
the same room B.S. 5440 - Part 2 should
be consulted to determine the air vent
requirements.
If the appliance is installed in a cellar or
basement, it is advisable to provide an
air vent of 65 cm, irrespective of the room
volume.
Gas Safety Regulations
The law requires that all gas appliances
are installed by competent persons in
accordance with the current gas safety
regulations. Failure to install appliances
correctly may lead to prosecution.It is in
your own interest, and that of safety, to
ensure that the law is complied with. The
hob should be installed in accordance with
the Gas Safety (Installation and Use)
Regulations, the Building Regulations
issued by the Department of the Environment
and the Building Standard (Scotland)
(Consolidation) Regulations, issued by the
Scottish Development Department.
In the G.B., CORGI registered installers work
to safe standards of practice.

ENGLISH 15
KNOBS REPLACEMENT
1. Be sure that your hob is switched-off!
All knobs must be in closed position.
2. Pull upwards each knob of the cooktop
and store together after removal.
3. Take the kit with new knobs, which is
located in upper part of packaging and
remove the new knobs from the plastic bag.
4. Push each of knob on the valve shaft until
you feel the end of sliding (sparking may
occur).
5. Make sure that all the knobs are in the
right position.
6. Verify correct installation by switching
each burner separately.

ENGLISH 16
Packing
- The packing materials are 100%
recyclable and marked with the
recycling symbol ( ).
Products
This appliance is marked in compliance with
European Directive 2002/96/EC on Waste
Electrical and Electronic
Equipment (WEEE). By ensuring that this
appliance is correctly scrapped, the user
can help prevent potentially harmful
consequences for the environment and the
health of people.
The symbol on the product or
accompanying documentation indicates
that this product should not be treated as
domestic waste but must be taken to a
suitable centre for collection and recycling
of electrical and electronic equipment.
Disposal must be carried out in compliance
with local regulations on waste disposal.
For further information on the treatment,
recovery and recycling of this product,
contactyourcompetentlocalofce,the
household waste collection service or the
shop where you purchased the appliance.
Declaration of Conformity
- This cooking hob has been designed,
constructed and put on the market in
conformity with:
- safety requirements of “Gas”
Directive 2009/142/EEC;
- safety objectives of “Low Voltage”
Directive 2006/95/EC (which
replaces 73/23/EEC as amended).
- protection requirements of “EMC”
Directive 2004/108/EEC;
- This cooking hob (Class 3) has been
designed only for cooking food. Any
other use (such as heating a room) is
improper and dangerous.
Environmental concerns

ENGLISH 17
IKEA GUARANTEE
How long is the IKEA guarantee valid?
Thisguaranteeisvalidforve(5)yearsfrom
the original date of purchase of your appliance
at IKEA, unless the appliance is named LAGAN
in which case two (2) years of guarantee
apply. The original sales receipt, is required
as proof of purchase. If service work is carried
out under guarantee, this will not extend the
guarantee period for the appliance.
Which appliances are not covered by the
IKEAve(5)yearsguarantee?
The range of appliances named LAGAN and
all appliances purchased in IKEA before 1st of
August 2007.
Who will execute the service?
IKEA service provider will provide the
service through its own service operations or
authorized service partner network.
What does this guarantee cover?
The guarantee covers faults of the appliance,
which have been caused by faulty construction
or material faults from the date of purchase
from IKEA. This guarantee applies to domestic
useonly.Theexceptionsarespeciedunder
the headline “What is not covered under this
guarantee?” Within the guarantee period,
the costs to remedy the fault e.g. repairs,
parts, labour and travel will be covered,
provided that the appliance is accessible for
repair without special expenditure. On these
conditions the EU guidelines (Nr. 99/44/
EG) and the respective local regulations
are applicable. Replaced parts become the
property of IKEA.
What will IKEA do to correct the problem?
IKEA appointed Service Provider will examine
the product and decide, at its sole discretion,
if it is covered under this guarantee. If
considered covered, IKEA Service Provider
or its authorized service partner through its
own service operations, will then, at its sole
discretion, either repair the defective product
or replace it with the same or a comparable
product.
What is not covered under this guarantee?
• Normal wear and tear.
• Deliberate or negligent damage, damage
caused by failure to observe operating
instructions, incorrect installation or by
connection to the wrong voltage, damage
caused by chemical or electrochemical
reaction, rust, corrosion or water damage
including but not limited to damage
caused by excessive lime in the water
supply, damage caused by abnormal
environmental conditions.
• Consumable parts including batteries and
lamps.
• Non-functional and decorative parts which
do not affect normal use of the appliance,
including any scratches and possible color
differences.
• Accidental damage caused by foreign
objects or substances and cleaning or
unblockingoflters,drainagesystemsor
soap drawers.
• Damage to the following parts: ceramic
glass, accessories, crockery and cutlery
baskets, feed and drainage pipes, seals,
lamps and lamp covers, screens, knobs,
casings and parts of casings. Unless such
damages can be proved to have been
caused by production faults.
• Cases where no fault could be found
during a technician’s visit.
• Repairs not carried out by our appointed
service providers and/or an authorized
service contractual partner or where non-
original parts have been used.
• Repairs caused by installation which is
faultyornotaccordingtospecication.
• The use of the appliance in a non-domestic
environment i.e. professional use.
• Transportation damages. If a customer
transports the product to his home or

ENGLISH 18
another address, IKEA is not liable for any
damage that may occur during transport.
However, if IKEA delivers the product
to the customer’s delivery address, then
damage to the product that occurs during
this delivery will be covered by IKEA.
• Cost for carrying out the initial installation
of the IKEA appliance.
However, if an IKEA appointed Service
Provider or its authorized service partner
repairs or replaces the appliance under
the terms of this guarantee, the appointed
Service Provider or its authorized
service partner will reinstall the repaired
appliance or install the replacement, if
necessary.
These restrictions do not apply to fault-free
workcarriedoutbyaqualiedspecialist
using our original parts in order to adapt the
appliancetothetechnicalsafetyspecications
of another EU country.
How country law applies
TheIKEAguaranteegivesyouspeciclegal
rights, which cover or exceed all the local legal
demands. However these conditions do not
limit in any way consumer rights described in
the local legislation.
Area of validity
For appliances which are purchased in one EU
country and taken to another EU country, the
services will be provided in the framework of
the guarantee conditions normal in the new
country.
An obligation to carry out services in the
framework of the guarantee exists only if
the appliance complies and is installed in
accordance with:
- thetechnicalspecicationsofthecountryin
which the guarantee claim is made;
- the Assembly Instructions and User Manual
Safety Information.
The dedicated AFTER SALES for IKEA
appliances
Please don’t hesitate to contact IKEA
appointed After Sales Service Provider to:
• makeaservicerequestunderthis
guarantee;
• askforclaricationsoninstallationofthe
IKEA appliance in the dedicated IKEA
kitchen furniture;
• askforclaricationonfunctionsofIKEA
appliances.
To ensure that we provide you with the best
assistance, please read carefully the Assembly
Instructions and/or the User Manual before
contacting us.
How to reach us if you need our service
Please refer to the last
page of this manual for the
full list of IKEA appointed
After Sales Service Provider
and relative national phone
numbers.
In order to provide you a quicker
service, we recommend to use the
specicphonenumberslistedonthis
manual. Always refer to the numbers
listedinthebookletofthespecic
appliance you need an assistance for.
Please also always refer to the IKEA
article number (8 digit code) and 12
digit service number placed on the
rating plate of your appliance.
SAVE THE SALES RECEIPT!
It is your proof of purchase and required
for the guarantee to apply. The sales
receipt also reports the IKEA name and
article number (8 digit code) for each of
the appliances you have purchased.
Do you need extra help?
For any additional questions not related
to After Sales of your appliances please
contact your nearest IKEA store call centre.
We recommend you read the appliance
documentation carefully before contacting us.

ITALIANO 19
La sicurezza vostra e degli altri è molto
importante.
Nel presente manuale e
nell'apparecchio stesso sono fornite
importanti avvertenze di sicurezza, da
leggere e osservare sempre.
Questo è il simbolo di pericolo,
relativo alla sicurezza, che avverte
dei potenziali rischi per l'utilizzatore e
per le altre persone.
Tutti i messaggi relativi alla sicurezza
saranno preceduti dal simbolo di
pericolo per la sicurezza e dai termini:
PERICOLO Indica una situazione
pericolosa che, se non evitata,
provoca lesioni gravi.
AVVERTENZA Indica una
situazione pericolosa che, se non
evitata, potrebbe provocare lesioni
gravi.
Tutti i messaggi relativi alla sicurezza
specicanoilpotenzialepericoloacui
si riferiscono, indicano come ridurre la
possibilità di lesioni e sottolineano ciò
che può succedere in caso di mancato
rispetto delle istruzioni.
L'apparecchio deve essere scollegato
dalla rete elettrica prima di effettuare
qualunque intervento d'installazione.
L'installazione e la manutenzione
devono essere eseguite da un tecnico
specializzato, in conformità alle
istruzioni del fabbricante e nel rispetto
delle norme locali vigenti in materia di
sicurezza e delle norme in materia di
gas. Usare soltanto ricambi originali.
Non riparare o sostituire qualsiasi parte
dell'apparecchiosenonspecicamente
richiesto nel manuale d'uso.
AVVERTENZA La mancata
osservanza delle indicazioni
fornite in questo manuale può
provocare un incendio o un'esplosione
con conseguenti danni materiali o
lesioni personali.
- Non conservare o usare benzina o
altrigaseliquidiinammabilinelle
vicinanze dell'apparecchio.
Cosa fare in caso si avverta odore di
gas:
- Non mettere in funzione nessun
apparecchio.
- Non toccare interruttori di corrente.
- Non utilizzare telefoni all'interno
dell'abitazione.
- Avvertire subito telefonicamente
l'ente di erogazione gas recandosi
da un vicino. Seguire le istruzioni
dell'ente di erogazione gas.
- Qualora non sia possibile mettersi
Informazionidisicurezza 19
Descrizionedelprodotto 22
Utilizzoquotidiano 22
Suggerimenti utili 23
Manutenzioneepulizia 23
Cosa fare se ... 24
Tabella iniettori 25
Datitecnici 26
Installazione 26
Consigli per la salvaguardia
dell'ambiente 31
GARANZIA IKEA 32
Informazionidisicurezza
Sommario

ITALIANO 20
in contatto con l'ente di erogazione
gas, contattare i vigili del fuoco.
- L'installazione e la manutenzione
dell'apparecchio devono essere
eseguite da un installatore
qualicato,dauncentrodi
assistenza o dall'ente di erogazione
gas.
- Utilizzare l'apparecchio unicamente
in stanze adeguatamente ventilate.
- I collegamenti di gas ed elettricità
devono essere conformi alle norme
locali.
- Quando si installa il piano di cottura,
dotarlo di un interruttore multipolare
con una distanza dal contatto
di almeno 3 mm che consenta
di scollegare completamente
l'apparecchio.
- La messa a terra dell'apparecchio è
obbligatoria a termini di legge.
- Il cavo di alimentazione deve essere
sufcientementelungodacollegare
l'apparecchio, una volta posizionato
nell'ubicazionedenitiva,allapresa
di corrente.
- Per l'allacciamento del gas,
utilizzare solo un tubo di metallo
essibileorigido.
- Se necessario, il cavo di
alimentazione deve essere sostituito
esclusivamente con un cavo di
alimentazione avente caratteristiche
identiche a quello originale fornito
dal produttore (tipo H05V2V2-F
90°C o H05RR-F). Questa
operazione deve essere eseguita da
untecnicoqualicato.
- Il fabbricante declina ogni
responsabilità per eventuali danni
subiti da persone, animali domestici
o beni, derivanti dalla mancata
osservanza delle norme sopra
indicate.
- Non usare prese multiple o
prolunghe.
- Non tirare il cavo di alimentazione
dell'apparecchio per staccarlo dalla
presa di corrente.
- Una volta terminata l'installazione,
i componenti elettrici non dovranno
più essere accessibili dall'utilizzatore.
- Evitare di toccare il piano di cottura
con parti del corpo umide e di
utilizzarlo a piedi nudi.
- Questo piano di cottura (classe 3) è
stato progettato per essere utilizzato
soltanto ed esclusivamente per la
cottura di cibi in ambienti domestici.
Non utilizzare l'apparecchio
per riscaldare l'ambiente. Tale
uso dell'apparecchio potrebbe
determinare un avvelenamento da
monossido di carbonio, oltre che
il surriscaldamento del piano di
cottura.
- Il fabbricante declina ogni
responsabilità per usi non
appropriati o per errate
impostazioni dei comandi.
- L'apparecchiatura e le parti
accessibili diventano roventi durante
l'utilizzo. Fare attenzione a non
toccare gli elementi riscaldanti. I
bambini di meno di 8 anni devono
essere tenuti lontani a meno che