IKEA IHI75UC6FS0 Product information sheet

36" (91.4 CM) ISLAND-MOUNT
CANOPY RANGE HOOD
Installation Instructions and Use & Care Guide
For questions about features, operation/performance, parts, accessories or service, call: 1-866-644-2449.
In Canada, for assistance, installation and service, call: 1-866-664-2449.
CAMPANA DE COCINA PARA ISLA CON
ESCUDETE DE 36" (91,4 CM)
Instrucciones de instalación y Manual de uso y cuidado
Si tiene preguntas respecto a las características, funcionamiento, rendimiento, partes, accesorios o servicio técnico,
llame al: 1-866-664-2449.
HOTTE DE CUISINIÈRE CONFIGURÉE
EN ÎLOT DE 36" (91,4 CM)
Instructions d’installation et Guide d’utilisation et d’entretien
Au Canada, pour assistance, installation ou service, composer le 1-866-664-2449.
Table of Contents/Índice/Table des matières...........................2
LIB0119520B/W10836371C
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.
FOR RESIDENTIAL USE ONL
Y.
IMPOR
TANTE: LEAY GUARDE ESTAS INSTRUCCIONES.
SÓLO P
ARA USO RESIDENCIAL.
IMPOR
TANT : LIRE ET CONSERVER CES INSTRUCTIONS.
POUR UTILISA
TION RÉSIDENTIELLE UNIQUEMENT
.
For warranty concerns, do not take the appliance back to the store. Please contact us in U.S.A. or Canada at 1-866-664-2449.
This product features a Limited Warranty - See the “Warranty” section for complete details. IKEA®appliances carry a 5-year warranty
(excludes LAGAN family - see warranty for coverage details).
NOTE: Proof of Purchase is required to obtain warranty service.
Si tiene dudas acerca de la garantía, no devuelva el aparato a la tienda. Póngase en contacto con nosotros en los EE.UU.
o en Canadá al 1-866-664-2449.
Este producto tiene una garantía limitada - Consulte la sección “Garantía” para obtener todos los detalles. Los aparatos IKEA®tienen
una garantía de 5-años (excluyendo los de la familia LAGAN - consulte la garantía para ver los detalles acerca de la cobertura).
NOTA: Se requiere la prueba de compra para obtener servicio bajo la garantía.
Pour toute question concernant l’application de la garantie, ne pas rapporter l’appareil au magasin. Veuillez nous contacter
aux É.-U. ou au Canada au 1-866-664-2449.
Ce produit est couvert par une garantie limitée – Voir la section “Garantie” pour des détails complets. Les appareils IKEA®
sont couverts par une garantie de 5-ans (hormis les appareils de la série LAGAN - voir la garantie pour des détails concernant
les modalités de garantie).
REMARQUE : Une preuve d’achat est obligatoire pour obtenir l'application de la garantie.

2
TABLE OF CONTENTS
ÍNDICE
TABLE DES MATIÈRES
RANGE HOOD SAFETY .................................................................3
INSTALLATION REQUIREMENTS.................................................5
Tools and Parts.............................................................................5
Location Requirements................................................................5
Venting Requirements..................................................................6
Electrical Requirements ...............................................................7
INSTALLATION INSTRUCTIONS...................................................8
Prepare Location..........................................................................8
Assemble Range Hood ................................................................9
Install Range Hood.......................................................................9
Make Electrical Connection .......................................................10
Install Duct Covers.....................................................................11
Complete Installation .................................................................12
RANGE HOOD USE......................................................................13
Range Hood Controls ................................................................13
RANGE HOOD CARE...................................................................14
Cleaning .....................................................................................14
WIRING DIAGRAM .......................................................................15
ASSISTANCE OR SERVICE.........................................................16
In the U.S.A. ...............................................................................16
In Canada ...................................................................................16
Accessories................................................................................16
WARRANTY ..................................................................................17
SEGURIDAD DE LA CAMPANA PARA COCINA........................19
REQUISITOS DE INSTALACIÓN.................................................21
Herramientas y piezas................................................................21
Requisitos de ubicación.............................................................21
Requisitos de ventilación ...........................................................22
Requisitos eléctricos..................................................................24
INSTRUCCIONES DE INSTALACIÓN.........................................24
Prepare la ubicación ..................................................................24
Ensamble la campana para cocina............................................25
Instalación de la campana para cocina.....................................26
Haga la conexión del suministro eléctrico.................................27
Instalación de las cubiertas del ducto .......................................28
Completar la instalación ............................................................29
USO DE LA CAMPANA DE COCINA ..........................................30
Controles de la campana para cocina.......................................30
CUIDADO DE LA CAMPANA DE COCINA .................................31
Limpieza ....................................................................................31
DIAGRAMA DE CABLEADO........................................................32
AYUDA O SERVICIO TÉCNICO...................................................33
En los EE.UU..............................................................................33
Accesorios..................................................................................33
GARANTÍA.....................................................................................34
Installation des cache-conduits.................................................44
Achever l’installation ..................................................................45
UTILISATION DE LA HOTTE .......................................................46
Commandes de la hotte de cuisinière.......................................46
ENTRETIEN DE LA HOTTE .........................................................47
Nettoyage...................................................................................47
SCHÉMA DE CÂBLAGE...............................................................48
ASSISTANCE OU SERVICE.........................................................49
Au Canada..................................................................................49
Accessoires................................................................................49
GARANTIE.....................................................................................50
SÉCURITÉ DE LA HOTTE DE CUISINIÈRE ...............................36
EXIGENCES D’INSTALLATION ...................................................38
Outils et pièces...........................................................................38
Exigences d’emplacement.........................................................38
Exigences concernant l’évacuation...........................................39
Spécifications électriques..........................................................40
INSTRUCTIONS D’INSTALLATION.............................................41
Préparation de l’emplacement...................................................41
Assemblage de la hotte .............................................................42
Installation de la hotte................................................................42
Raccordement électrique...........................................................43

3
RANGE HOOD SAFETY
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.

4
IMPORTA NT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS

5
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting
installation. Read and follow the instructions provided
with any tools listed here.
Tools Needed
■Level
■Drill with 11/4" (3.2 cm), 3/8" (9.5 mm), 1/8" (3.2 mm),
and 7/64" (2.75 mm) drill bits
■Pilot hole drill bits (determined by chimney support
attachment method)
■Pencil
■Wire stripper or utility knife
■Tape measure or ruler
■Pliers
■Caulking gun and weatherproof caulking compound
■Vent clamps
■Jigsaw or keyhole saw
■Flat-blade screwdriver
■Metal snips
■Phillips screwdriver
Parts Needed
■Home power supply cable
■1/2" (12.7 mm) UL listed or CSA approved strain relief
■3 UL listed wire connectors
For Vented Installations, You Will Also Need:
■1 wall or roof cap
■Metal vent system
For Non-Vented (Recirculating) Installations,
You Will Also Need:
■Charcoal Filter Kit Part Number W10412939 for non-vented
(recirculating) installations only. See “Assistance or Service”
section to order.
■6" (15.2 cm) diameter round metal vent duct -
length required is determined by ceiling height.
Parts Supplied
Remove parts from packages. Check that all parts are included.
■Hood ventilator assembly with canopy glass, retainer
brackets, rubber seals, and LED lights installed
■Vent transition with backdraft damper installed
■Metal grease filter
■Mounting template
■2 - Upper vent covers
■2 - Lower vent covers
■4 - Plastic vent clips
■Upper horizontal support bracket
■Horizontal support
■8 - Vertical supports
■2 - 2.9 x 3 mm screws (T10 drive)
■4 - 3.5 x 6.5 mm screws (T10 drive)
■2 - 3.5 x 9.5 mm mounting screws (Phillips)
■62 - 4.2 x 8 mm screws (T20®† drive)
■4 - 5 x 45 mm mounting screws (#2 Phillips drive)
■Air deflector (for non-vented/recirculating installation)
■T10 Torx®† adapter
■T20®Torx®adapter
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer’s responsibility to comply with installation clearances
specified on the model/serial/rating plate. The model/serial/
rating plate is located behind the left filter on the rear wall
of the vent hood.
Canopy hood location should be away from strong draft areas,
such as windows, doors, and strong heating vents.
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance.
Grounded electrical outlet is required. See “Electrical
Requirements” section.
Because of the size and weight of this island hood, the chimney
support must be securely attached to the ceiling.
■For plaster or drywall ceilings, the chimney support must
be attached to joists. If this is not possible, you must build
a support structure behind the plaster or drywall. The
support structure must be able to support 80 lbs (36.6 kg).
This range hood is recommended for use with cooktops
with a maximum total rating of 60,000 BTUs or less.
The range hood is factory set for venting through the roof or wall.
For non-vented (recirculating) Installation see “Non-vented
(recirculating) Installation” in “Install Range Hood” section.
Charcoal Filter Kit Part Number W10412939 is available from
your dealer or an authorized parts distributor.
All openings in ceiling and wall where canopy hood will
be installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title
24 CFR, Part 328 (formerly the Federal Standard for Mobile
Home Construction and Safety, Title 24, HUD, Part 280)
or when such standard is not applicable, the standard for
Manufactured Home Installation 1982 (Manufactured Home
Sites, Communities and Setups) ANSI A225.1/NFPA 501A
or latest edition, or with local codes.
†®TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

6
Product Dimensions
* Vented installations only
** Non-vented (recirculating) installations only
Installation Dimensions
IMPORTANT:
Minimum distance “C”: 24" (61 cm) from electric cooking
surface, 27" (68.6 cm) from gas cooking surface
Suggested maximum distance “C”: 36" (91.4 cm)
The chimneys can be adjusted for different ceiling heights.
See the following chart.
Vented Installations
Min. ceiling height Max. ceiling height
Electric cooking
surface 7' 8" (2.34 m) 9' 10" (3 m)
Gas cooking
surface 7' 11" (2.41 m) 9' 10" (3 m)
Non-Vented (Recirculating) Installations
Min. ceiling height Max. ceiling height
Electric cooking
surface 7' 8" (2.34 m) 10' 3" (3.12 m)
Gas cooking
surface 7' 11" (2.41 m) 10' 3" (3.12 m)
NOTE: The range hood chimneys are adjustable and designed
to meet varying ceiling or soffit heights depending on the
distance “C” between the bottom of the range hood and the
cooking surface. For higher ceilings, a Stainless Steel Chimney
Extension Kit Part Number EXTKIT26FS is available from your
dealer or an authorized parts distributor. The chimney extension
replaces the upper chimney shipped with the range hood.
Venting Requirements
■Vent system must terminate to the outdoors except
for non-vented (recirculating) installations.
■Do not terminate the vent system in an attic or other
enclosed area.
■Do not use 4" (10.2 cm) laundry-type wall cap.
■Use metal vent only. Rigid metal vent is recommended.
Plastic or metal foil vent is not recommended.
■The vent system must have a damper. If the roof
or wall cap has a damper, do not use the damper
supplied with the range hood.
For the Most Efficient and Quiet Operation:
■Use a straight run or as few elbows as possible.
■Use no more than three 90° elbows.
■Make sure there is a minimum of 24" (61 cm) of straight
vent between the elbows if more than 1 elbow is used.
■Do not install 2 elbows together.
■Use vent clamps to seal all joints in the vent system.
■Use caulking to seal exterior wall or roof opening
around the cap.
■The size of the vent should be uniform.
Cold Weather Installations
An additional backdraft damper should be installed to minimize
backward cold air flow and a thermal break should be installed
to minimize conduction of outside temperatures as part of the
vent system. The damper should be on the cold air side of the
thermal break.
The break should be as close as possible to where the vent
system enters the heated portion of the house.
A
B
C
D
E
F
A. 121/4" (31.1 cm)
B. 133/16" (33.5 cm)
C. *293/4" (75.6 cm) min. 4413/16" (113.8 cm) max.
**293/4" (75.6 cm) min. 4913/16" (126.5 cm) max.
D. 31/2" (8.9 cm)
E. 36" (91.4 cm)
F. 253/16" (64 cm)
A
B
D
C
A. Countertop height
B. Hood height from ceiling to bottom
of the range hood filter surface: D-A-C=B
C. Hood height: 24" (61 cm) min. from electric
cooking surface, 27" (68.6 cm) min. from gas
cooking surface, suggested 36" (91.4 cm) max.
D. Ceiling height

7
Makeup Air
Local building codes may require the use of makeup air systems
when using ventilation systems greater than specified CFM of
air movement. The specified CFM varies from locale to locale.
Consult your HVAC professional for specific requirements in
your area.
Venting Methods
This island hood is factory set for venting through the roof.
A 6" (15.2 cm) round vent system is needed for installation
(not included). The hood exhaust opening is 6" (15.2 cm) round.
NOTE: Flexible vent is not recommended. Flexible vent
creates back pressure and air turbulence that greatly
reduce performance.
Vent system can terminate either through the roof or wall.
To vent through a wall, a 90° elbow is needed.
For Non-Vented (Recirculating) Installations
If it is not possible to vent cooking fumes and vapors to the
outside, the hood can be used in the non-vented (recirculating)
version, fitting a charcoal filter and the deflector. Fumes and
vapors are recycled through the top grille. To order, see the
“Assistance or Service” section.
NOTE: If codes permits, wall venting can be an option
for 2-story homes.
Calculating Vent System Length
To calculate the length of the system you need, add the
equivalent feet (meters) for each vent piece used in the system.
Vent Piece 6" (15.2 cm) Round
45° elbow 2.5 ft (0.8 m)
90° elbow 5 ft (1.5 m)
Maximum equivalent vent length is 35 ft (10.7 m).
Example Vent System
The following example falls within the maximum
recommended vent length of 35 ft (10.7 m).
1 - 90° elbow = 5 ft (1.5 m)
1 - wall cap = 0 ft (0 m)
8 ft (2.4 m) straight = 8 ft (2.4 m)
Length of system = 13 ft (3.9 m)
Electrical Requirements
Observe all governing codes and ordinances.
Ensure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA
70 (latest edition), or CSA Standards C22.1-94, Canadian
Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition)
and all local codes and ordinances.
If codes permit and a separate ground wire is used,
it is recommended that a qualified electrician determine
that the ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
■A 120-volt, 60 Hz., AC-only, 15-amp, fused electrical
circuit is required.
■If the house has aluminum wiring, follow the
procedure below:
1. Connect a section of solid copper wire to the
pigtail leads.
2. Connect the aluminum wiring to the added section
of copper wire using special connectors and/or tools
designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer’s recommended
procedure. Aluminum/copper connection must conform with
local codes and industry accepted wiring practices.
■Wire sizes and connections must conform with the rating of
the appliance as specified on the model/serial/rating plate.
The model/serial/rating plate is located behind the left filter
on the rear wall of the range hood.
■Wire sizes must conform to the requirements of the National
Electrical Code, ANSI/NFPA 70 (latest edition), or CSA
Standards C22. 1-94, Canadian Electrical Code, Part 1
and C22.2 No. 0-M91 (latest edition), and all local codes
and ordinances.
Non-Vented (Recirculating) Roof Venting
B
A
B
A
A. Deflector
B. 6" (15.2 cm) round vent
A. Roof cap
B. 6" (15.2 cm) round vent
90 elbo
w6 ft (1.8 m)
2 ft
(0.6 m)
Wall cap

8
INSTALLATION INSTRUCTIONS
Prepare Location
■Lay out the vent duct system before installing the range
hood to determine the best routing for the vent duct.
■It is recommended that the vent system be installed
before the range hood is installed.
■Before making cutouts, make sure there is proper
clearance within the ceiling for exhaust vent.
■Range hood is to be installed 24" (61 cm) min.
for electric cooking surfaces, 27" (68.6 cm) min.
for gas cooking surfaces, to a suggested maximum
of 36" (91.4 cm) above the cooking surface.
■Remove film from metal surfaces as needed prior
to assembly.
■Check your ceiling height and the range hood height
maximum before you install your hood.
1. Disconnect power.
2. Determine which venting method to use: roof, wall
or non-vented.
3. Select a flat surface for assembling the range hood.
Place covering over that surface. Place two 3" (7.6 cm)
high spacers (not included) onto the covered surface.
NOTE: Cover the spacers to avoid damage to the
range hood surface.
4. Using 2 or more people, lift range hood
onto covered spacers.
Range Hood Mounting Screws Installation
1. Determine and mark the centerline on the ceiling
where the range hood will be installed, considering
the requirements for ceiling support structures. See
the “Location Requirements” section. Make sure the
range hood is centered over the cooking surface.
2. Tape template in place on the ceiling at the marked
centerline. The line for the front of the range hood
should be parallel to the front of the cooktop.
3. Use a pencil to mark the mounting screws, wire access,
and duct hole locations on the ceiling.
NOTE: Mounting hole locations should be into a ceiling
support structure capable of holding 80 lbs (36.6 kg).
Remove the template.
4. Drill 4 - 3/16" (4.8 mm) pilot holes for mounting the
upper horizontal support.
Complete Preparation
1. Determine the required location for the home power supply
cable and drill a 1/2" (1.3 cm) diameter hole for wire access.
2. Run 1/2" (1.3 cm) conduit and wires or home power supply
cable according to the National Electrical Code or CSA
Standards and local codes and ordinances. There must
be enough 1/2" conduit and wires or home power supply
cable from the fused disconnect (or circuit breaker) box to
make the connection in the hood’s electrical terminal box.
NOTE: Do not reconnect power until installation is complete.
3. For vented installations only: Using a jigsaw or keyhole
saw, cut a 61/2" (16.5 cm) diameter hole for the vent duct.
4. Attach the upper horizontal support bracket with
4 - 5 x 45 mm #2 Phillips wood screws.
NOTE: Upper horizontal support screws must be into a
ceiling support structure capable of holding 80 lbs (36.6 kg).
WARNING
Excessive Weight Hazard
Use two or more people to move and install
range hood.
Failure to do so can result in back or other injury.
AB
C
A. Covered spacers
B. Glass canopy
C. Ventilator assembly
A
B
A. Upper horizontal support
B. 5 x 45 mm screws (#2 Phillips drive)

9
Assemble Range Hood
1. Install transition on top of hood (if removed for shipping)
with 2 - 3.5 x 9.5 mm Phillips drive sheet metal screws.
2. Position the 4 vertical supports (A) with the notches
at the bottom and attach to the range hood using
16 - 4.2 x 8 mm T20®screws. Use a T20®Torx®drive
(or T20®adapter provided) to tighten all assembly screws.
3. Position the lower horizontal support (B) as shown (flanges
pointed down). Attach to the lower vertical supports using
8 - 4.2 x 8 mm T20®screws. The lower horizontal support
can be positioned at any of the three mounting hole
locations in the lower vertical supports.
4. Attach a second set of vertical supports (A) and set
the vertical height (B). See “Installation Dimensions”
in the “Location Requirements” section to help
determine the desired dimension for vertical height “B.”
Secure with 16 - 4.2 x 8 mm T20®screws.
Install Range Hood
Non-Vented (recirculating) Installation
1. Attach the air deflector to the upper horizontal support
using 2 - 4.2 x 8 mm T20®mounting screws.
2. Measure the length of 6" (15.2 cm) duct needed
to connect the transition to the deflector.
NOTE: Vent should fit up inside the deflector
1" (2.5 cm) minimum.
3. Install vent between the transition and the deflector.
NOTE: To make vent installation easier, temporarily remove
the deflector from the chimney support bracket and replace
after vent section is in place.
4. Seal all connections with vent clamps. Continue
with “Range Hood Installation” in this section.
Range Hood Installation
1. Using 2 or more people, lift the range hood assembly
and attach it by snapping the vertical supports to the
spring clips in the upper horizontal support bracket
that is mounted to the ceiling.
NOTE: The range hood assembly must be held in place
while you are installing the screws in the next step.
2. Install 16 - 4.2 x 8 mm T20®screws and tighten to secure.
A
B
A. Vent transition
B. 3.5 x 9.5 mm screw
B
A
A
CC
A. Vertical supports
B. Horizontal support
C. Notched end
A
B
C
C
C
C
D
A. Vertical supports (4)
B. Horizontal support
C. Screws 4.2 x 8 mm T20®(8)
D. Mounting hole locations for horizontal support
B
AA
A. Vertical supports
B. Vertical height
B
B
A
A. Deflector
B. 2 - 4.2 x 8 mm T20®mounting screws
A
A. Mounting screws

10
Connect Vent System
1. Install vent system.
2. Push duct over the exhaust outlet. Seal all connections
with vent clamps.
3. Use caulk to seal all openings.
Make Electrical Connection
1. Disconnect power.
2. Remove terminal box cover using a T10 Torx®drive
(or T10 adapter provided) to remove the screws.
3. Remove the knockout in the terminal box and install
a UL listed or CSA approved 1/2" strain relief.
4. Run home power supply cable through strain relief
into terminal box.
5. Use UL listed wire connectors and connect
black wires (C) together.
6. Use UL listed wire connectors and connect
white wires (E) together.
7. Connect green (or bare) ground wire from home power
supply to yellow-green ground wire (F) in terminal box
using UL listed wire connectors.
8. Tighten strain relief screw.
9. Install terminal box cover.
10. Check that all light bulbs are secure in their sockets.
11. Reconnect power.
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
C
A
B
A. Terminal box
B. Knockout
C. Terminal box cover
AB
C
D
E
F
A. Home power supply cable
B. UL listed or CSA
approved strain relief
C. Black wires
D. UL listed wire connectors
E. White wires
F. Green (or bare) and
yellow-green ground wires
WARNING
Electrical Shock Hazard
Electrically ground blower.
Connect ground wire to green and yellow ground wire
in terminal box.
Failure to do so can result in death or electrical shock.