Ikegami OCP-399 User manual

AUTOTALLY
LENS EXT
FREE
KNOB
RANGE SENS
IRIS
OPEN
FULL ±1±2
OPEN SHORT
CABLE
ALARM
CALL
IRIS
PED
ENCR
GY
B RGB
MON SEL
CLS
LOCKKNEE
AUTO
SAT
COLOR
DTL
SKIN
DTL
SOFT
DTL SKIN C.SAT GAMMA
KNEE PT. SLOPE
GAIN
BLACK
FLARE
MASTER
FLARECLR
FILTER
EDCBA54321
HEAD
ND CC EFF
SCENE FILE
STORE
3
7
4
8
1
5
2
6
SHUTTER SUPER V
ON VAR. GAMMA
GAIN(dB)
GAMMA
BLK
1000 +1254
.
MATCH
COLOR
MASTER /PAGE
PM IND
LEVEL SKIN HUE QUICK START AWB ABB
AUTO SETUP
CAP BARS CAL CORR
COLOR
MODE SWITCH
KNEE
SUPER
MATRIX
123 L HM
BLK STRETCH
OFFOFF
PANEL
ENABLEPOWER
VF
POWER
HEAD
CAM
POWER
OFF
-11 -7 -3 +3 +7 +11
ON
EFF1 EFF2
CUSTOM COLOR
(%)
0
PED
HOLD MENU
OPERATION CONTROL PANEL
OCP-399
OPERATION MANUAL

0403 1st Edition (U) (E)
OPERATION CONTROL PANEL
OCP-399
OPERATION MANUAL
AUTOTALLY
LENS EXT
FREE
KNOB
RANGE SENS
IRIS
OPEN
FULL ±1±2
OPEN SHORT
CABLE
ALARM
CALL
IRIS
PED
ENCR
GY
B RGB
MON SEL
CLS
LOCKKNEE
AUTO
SAT
COLOR
DTL
SKIN
DTL
SOFT
DTL SKIN C.SAT GAMMA
KNEE PT. SLOPE
GAIN
BLACK
FLARE
MASTER
FLARECLR
FILTER
EDCBA54321
HEAD
ND CC EFF
SCENE FILE
STORE
3
7
4
8
1
5
2
6
SHUTTER SUPER V
ON VAR. GAMMA
GAIN(dB)
GAMMA
BLK
1000 +1254
.
MATCH
COLOR
MASTER /PAGE
PM IND
LEVEL SKIN HUE QUICK START AWB ABB
AUTO SETUP
CAP BARS CAL CORR
COLOR
MODE SWITCH
KNEE
SUPER
MATRIX
123 L HM
BLK STRETCH
OFFOFF
PANEL
ENABLEPOWER
VF
POWER
HEAD
CAM
POWER
OFF
-11 -7 -3 +3 +7 +11
ON
EFF1 EFF2
CUSTOM COLOR
(%)
0
PED
HOLD MENU

Copyright © 2004 Ikegami Tsushinki Co., Ltd.
Copyright © 2004 Ikegami Tsushinki Co., Ltd.
We reserve the copyright on the software we create.
We reserve the copyright on the software we create.
No part of this publication may be modified or reproduced in any form, or by any means, without prior written permission from Ikegami
No part of this publication may be modified or reproduced in any form, or by any means, without prior written permission from Ikegami
Tsushinki Co., Ltd.
Tsushinki Co., Ltd.

SAFETY PRECAUTIONS
The safety precautions for using this product are described below. Please read them thoroughly before use.
1. Safety Alert Symbols
This manual employs the following "Safety Alert Symbols" to call attention to hazards:
WARNING
㪑㩷㩷 㩷 Indicates that mishandling of the product may lead to a danger resulting in a serious injury or
death.
CAUTION
: Indicates that mishandling of the product may lead to a danger resulting in an injury or
property damage.
2. Handling Precautions
This product is designed with safety in mind; however, any electrical equipment may cause electric shock or equipment
damage if used in an inappropriate manner or under unsuitable conditions.
Therefore, please follow the following instructions when handling this product:
(1) Do not remove the covers or disassemble unless absolutely necessary, to prevent malfunction or electric shock.
(2) Do not drop or expose the equipment to a strong vibration or shock.
A strong vibration or shock may cause equipment damage or failure.
(3) Be sure to turn OFF the power switch before removing modules.
(4) Avoid using or storing in the following conditions. It may cause damage to the product.
- Extremely high/low temperature
- High humidity or dusty
- Exposed to water or other liquid
- Strong vibration or shock
- Strong magnetic field or radio waves
- lightning
- In rain or snow without the cover
(5) When carrying or storing the product, always use a carrying case.
(6) Be sure to hold the plug and pull when disconnecting the cable. Failure to do so may cause a fire or electric shock due to
a broken cable.
(7) Do not drop or insert metal objects such as clips or foreign objects into the equipment.
(8) Do not spread or spill water or other liquid on the equipment.
(9) Regarding the lithium battery
- Do not use an unspecified battery.
- Wrong usage of batteries may cause liquid leak, explosion, and heat, and at worst injury or fire. When replacing or dis-
carding a battery, please contact Ikegami's sales and service centers.
3. Regular Maintenance Recommended
This product includes parts that wear out and have a limited life even in proper use or storage. Therefore, regular
maintenance (once every 3 years or 8000 hours use) is recommended to extend the life and safe use of this product for a
long time. Please contact Ikegami's sales and service centers or Techno Ikegami Co., Ltd. for the regular maintenance and
repair of our products.
SAFETY PRECAUTIONS i
OCP-399 0403 VOL1 (U) (E) OCP-399

HOW TO USE OPERATION MANUAL
The OCP-399 OPERATION CONTROL PANEL OPERATION MANUAL is intended to describe how to operate the OCP-399.
This manual is written for readers with a basic knowledge of handling broadcast cameras and Base Station (BS), so technical terms
are not explained here.
This manual consists of five chapters. Related topics are included in the same chapter as much as possible so that you do not have to
turn pages back and forth.
Each chapter is arranged in the order of actual operating procedures. By reading it in sequence, you can smoothly perform a series
of steps, from installation and connection to operation in a proper manner.
[Structure of Operation Manual]
1. NAME and FUNCTION : Explains the name and function of each switch and control on the
OCP-399.
2. INSTALLATION and CONNECTION :
Explains how to connect the OCP-399 to the camera or BS. Also explains
the specifications of connector pins.
3. OPERATION : Explains how to turn on power, how to check operation, and how to
activate various functions.
4. TROUBLESHOOTING   : Explains self-diagnosis function.
5. SPECIFICATIONS :
Lists the specifications and external dimensions of the OCP-399.
[Symbols]
The symbols used in this manual are as follows:
Note: Supplementary information on the matter just discussed
Reference: Sections or pages where related information is available
[Reference Manuals]
- HK-399PW COLOR CAMERA MAINTENANCE MANUAL
- HK-399PW COLOR CAMERA OPERATION MANUAL
- BS-388 BASE STATION INSTRUCTION MANUAL
ii HOW TO USE OPERATION MANUAL
OCP-399 OCP-399 0403 VOL1 (U) (E)

OCP-399 0403 VOL1 (U) (E) OCP-399
CONTENTS iii
OCP-399
OPERATION CONTROL PANEL
OPERATION MANUAL
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
HOW TO USE OPERATION MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii
1. NAME and FUNCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2. INSTALLATION and CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1 Cable Connection Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 OCP Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.3 Connector Pin Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
3. OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1 Turning ON Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1.1 BS-388 for Non-EU Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1.2 BS-388 for EU Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2 Operation Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.2.1 Checking Color Bars Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.2.2 Checking with Test Pulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.2.3 Checking Images on Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.3 Auto Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
3.3.1 Quick Auto Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.3.2 Auto Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.3.3 AWB (Auto White Balance) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3.3.4 ABB (Auto Black Balance) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
3.4 Operation Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3.4.1 Selecting Shutter Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3.4.2 Improving Reproducibility of Low Luminance Level Part (Black Press/Black Stretch) . . . . . . . . . . . . 3-10
3.4.3 Suppressing Glare on the Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3.4.4 Correcting Color Temperature for Multiple Cameras (Color Matching) . . . . . . . . . . . . . . . . . . . . . . . . 3-12
3.4.5 Creating Scene Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
3.5 Menu Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
3.6 Internal Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
4. TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1 Alarm Lamp Flashes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

OCP-399 OCP-399 0403 VOL1 (U) (E)
iv CONTENTS
5. SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.1 Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.2 Control Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.3 Environmental Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.4 External Dimensions Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

1. NAME and FUNCTION
The diagrams below show the locations of switches and connectors.
Note:
The switches and VR controls on the OCP do not work if the connected camera does not have corresponding functions.
Refer to the manual for the connected camera for available functions.
AUTOTALLY
LENS EXT
FREE
KNOB
RANGE SENS
IRIS
OPEN
FULL ±1±2
OPEN SHORT
CABLE
ALARM
CALL
IRIS
PED
ENCR
GY
B RGB
MON SEL
CLS
LOCKKNEE
AUTO
SAT
COLOR
DTL
SKIN
DTL
SOFT
DTL SKIN C.SAT GAMMA
KNEE PT. SLOPE
GAIN
BLACK
FLARE
MASTER
FLARECLR
FILTER
EDCBA54321
HEAD
ND CC EFF
SCENE FILE
STORE
3
7
4
8
1
5
2
6
SHUTTER SUPER V
ON VAR. GAMMA
GAIN(dB)
GAMMA
BLK
1000 +1254
.
MATCH
COLOR
MASTER /PAGE
HOLD MENU
PM IND
LEVEL SKIN HUE QUICK START AWB ABB
AUTO SETUP
CAP BARS CAL CORR
COLOR
MODE SWITCH
KNEE
SUPER
MATRIX
123 L HM
BLK STRETCH
OFFOFF
PANEL
ENABLEPOWER
VF
POWER
HEAD
CAM
POWER
OFF
-11 -7 -3 +3 +7 +11
ON
EFF1 EFF2
CUSTOM COLOR
(%)
0
PED
P.S CONT
PREVIEW
COLOR MATCH
COMM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CAM POWER switch
HEAD POWER indicator
VF POWER switch
COLOR MATCH switch
MASTER switch
PANEL ENABLE switch
PM IND/PAGE switch
AUTO SETUP switches
MODE switches
FILTER switches
SCENE FILE switches
MODE switches/VR controls
IRIS indicator
AUTO IRIS switch
JOYSTICK (IRIS, M-PED)
(PREVIEW switch)
16
17
18
19
20
21
22
23
24
25
26
27
28
29
CALL switch
ALARM indicator
CABLE OPEN indicator
CABEL SHORT indicator
IRIS RANGE control
IRIS SENS control
MONITOR SELECT switch
KNOB FREE switch
LENS EXT indicator
TALLY indicators
PS CONT connector (OCP-399U only)
COLOR MATCH connectors
COMMAND connector
PREVIEW connector
26
29 28
27
1 2 3 654
7
8
9
11
10
12
13
16
14
15
20
25
22
17
18
21
19
23
24
The switches of cannot be used when the
on-air tally guard is set to "ON".
The START, AWB and ABB switches can be used
only when the auto setup is canceled in the on-air
mode, but the auto setup cannot be executed.
(Refer to "3.6 Internal Switch Settings" for the on-air
tally guard settings.)
Rear View
Note:
㩷1.䇭NAME and FUNCTION㩷1-1
OCP-399 0403 VOL1 (U) (E) OCP-399

1 CAM POWER switch
This switch can control the MAIN POWER of the BS-388 for non-EU area when the BS MAIN POWER switch on the front of
the BS-388 is set to “ON” and the POWER REMOTE/LOCAL switch is set to “REMOTE.” The switch lights when this switch
is set to “ON.”
Note:
The BS-388 for EU area can only control the ON/OFF of the power that is supplied from the BS to the camera. It cannot
control the MAIN POWER of the BS. The BS-593 cannot remote control power supply.
2 HEAD POWER indicator
Lights when the HEAD POWER is ON. Flashes when the camera cable is faulty (OPEN, SHORT).
3 VF POWER switch
Turns ON/OFF the power supply of the VF. When turning OFF the power supply of the VF, press the switch continuously for
two seconds.
Note:
This switch is valid only if the camera head has the VF power ON/OFF function. This switch does not work for the 1.5-inch,
2-inch, 5-inch, and 6-inch viewfinders.
4 COLOR MATCH switch
When pressed, the camera is changed from the master camera to the slave camera to receive color match information. (Refer to
the MASTER switch.)
Reference:
Refer to “3.4.4 Correcting Color Temperature for Multiple Cameras (Color Matching)” for details.
5 MASTER switch
When pressed with the COLOR MATCH switch ON, the camera is changed to the master camera to transfer color match
information to other cameras. (Refer to the COLOR MATCH switch.)
Reference:
Refer to “3.4.4 Correcting Color Temperature for Multiple Cameras (Color Matching)” for details.
6 PANEL ENABLE switch
Enables operations of the OCP.
7 PM IND/PAGE switch
Displays various information in character format to the PM output of the BS. The information is displayed as shown below
each time the switch is pressed.
Display OFF
0
1
2
3
Page
Page
Page
Page
Cameraman's name display
Self-diagnostic information display
Auto setup monitor display
Standby display
.....................
.....................
.....................
.....................
When the PM IND/PAGE switch is held for more than 1 second, the mode is changed to menu remote mode, and the menu of
the camera or BS can be controlled from the OCP. Refer to “3.5 Menu Remote” for details.
8 AUTO SETUP switches
- LEVEL switch, SKIN HUE switch, QUICK switch, START switch
When the START switch is pressed after pressing the LEVEL, SKIN HUE or QUICK switch, the respective auto setups
will be executed. Pressing the switch again while executing setups will cancel the execution. When the execution ends, the
lamp goes OFF. When the execution fails, the START switch flashes. After confirming the failure, press the START switch
again to clear the failure.
1-2㩷1.䇭NAME and FUNCTION
OCP-399 OCP-399 0403 VOL1 (U) (E)

- AWB switch, ABB switch
Used to execute the AWB (auto white balance) or ABB (auto black balance). When the execution ends, the lamp goes OFF.
When the execution fails, the lamp flashes. After confirming the failure, press the flashing switch again to clear the failure.
9 MODE switches
- CAP switch
Used to set the filter to the CAP position.
- BARS switch
Used to set the ENC output signal to the color bar signal.
- CAL switch
Inputs the 100% level CAL signal to the first stage of the internal PRE PROC module on the right side of the camera head.
When the TEST PULSE switch is turned ON by MCP, the lamp of the CAL switch flashes.
- SHUTTER switches
When the SHUTTER ON/OFF switch is pressed, the lamp lights and the preset shutter mode is set and the electronic shutter
starts working. When the switch is pressed again, the lamp goes off and the electronic shutter also stops operating.
While the electronic shutter is operating, the shutter speed will be displayed on the LED display. Select the shutter speed
using the UP/DOWN switches.
LED Display
Shutter Speed
100 120 250 500 1000 2000
1/100 sec 1/120 sec 1/250 sec 1/500 sec 1/1000 sec 1/2000 sec
DOWN UP
Pressing the VARIABLE SHUTTER switch sets the variable shutter mode. The VARIABLE indicator lights up and the
shutter speed is displayed on the LED display. The shutter speed can be selected using the UP/DOWN switches.
- COLOR CORR switch
Used to set COLOR CORRECT to ON. The hue and level of COLOR CORRECT are previously set by the MCP.
- MATRIX switch
Used to select one of the three preset MATRIX settings (1, 2, or 3) or OFF. The LED above the switch indicates the current
preset settings. When it is set to OFF, the switch lamp lights. Each time the switch is pressed, 1, 2, 3, or OFF is selected in
that order repeatedly. Normally, set to "1." The three preset values are previously set by the MCP.
- SUPER KNEE switch
Used to set SUPER KNEE to ON. One of the three SUPER KNEE levels (L, M, or H) can be selected. "H" produces the
largest effect, "M" the next, and "L" the smallest effect. The LED above the switch indicates the current settings. When it
is set to OFF, the switch lamp lights. Each time the switch is pressed, L, M, H, or OFF is selected in that order repeatedly.
Normally, set to "M."
- CUSTOM COLOR switch (EFF1, EFF2)
Used to set CUSTOM COLOR to ON. Two CUSTOM COLOR channels are available, each of which can be independently
set to ON using the EFF1 switch or EFF2 switch. The hue and level of EFF1 and EFF2 are previously set by the MCP.
- BLK STRETCH switch
Used to select the black stretch/press settings. Press the "ON" switch and then the UP/DOWN switch. Any of the
following positions can be selected:
Black stretch : +3, +5, +7, +9, +11
Black press : -11, -9, -7, -5, -3
The LED indicates the current settings. When LEDs for ±11 and ±7 light simultaneously, it indicates ±9. Similarly, when
LEDs for ±7 and ±3 light simultaneously, it indicates ±5.
- GAMMA switch
Select GAMMA using the UP/DOWN switch. One of the following values can be selected: OFF, 0, 45, 0.4, or 0.35. The
LED display indicates the current setting value. Normally, set to "0.45."
- GAIN switch
Select Master Gain using the UP/DOWN switch. One of the following values can be selected: -3, 0, +3, +6, +9, +12, +18,
㩷1.䇭NAME and FUNCTION㩷1-3
OCP-399 0403 VOL1 (U) (E) OCP-399