Ikegami HTM-1005R User manual

HTM-1005R/RA
HDTV/SDTV MULTI FORMAT
COLOR MONITOR
OPERATION MANUAL
MODEL

Caution (AC/DC input type)
For the use of nickel-hydrogen batteries, a parallel connection
of two or more batteries is possible. Battery makers, however,
say that their warranty will not cover any products if they are
used for “monitors or lighting equipment”, since the lifetime
of batteries is shortened in such use environments due to
the heat generated by the batteries themselves.
It is therefore not recommendable to use nickel hydrogen
batteries for this monitor.

SA 1966 SA 1965
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK).
NO USER-SERVICEABLE
PARTS INSIDE. REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead inside a triangle is intended to warn the user that
parts inside the product are dangerous and many cause electric hazards.
The exclamation mark inside a triangle is intended to inform users that important
operating and servicing instructions are provided with the equipment.
SA 1966
SA 1965
WARNING: FOR CONTINUED SAFETY, REPLACE SAFETY CRITICAL
COMPONENTS ONLY WITH MANUFACTURE’S RECOMMENDED
PARTS (REFER TO SERVICE LITERATURE).
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR WATER.
INFORMATION TO USER FOR FCC
Warning
This equipment generates, uses and can radiated radio frequency energy
and if not installed and used in accordance with the instruction manual.
May cause interference to radio communications.
It has been tested as a Class A computing device and found to comply
within the limits for a Class A computing device in accordance with the
specifications in subpart J of Part 15 of FCC Rules, which are designed
to provide reasonable protection against such interference when
operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause
interference in which case the user will be required at his own expense
to take whatever measures may be required to correct the interference.
Instructions for Disposal of Electric and Electronic Equipment in Private Household
Disposal of used Electric and Electronic Equipment
(Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product, or in the related documents in the package, indicates that this product shall not
be treated as normal household waste. Instead, it should be taken to a proper applicable collection point or
depot for the recycling of electric and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent possible negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The
recycling of materials will help to conserve natural resources.
For more detailed information about recycling of this product, please contact your local city authority, your household
waste disposal service or the place where you purchased the product.

IMPORTANT SAFETY INSTRUCTION
1. General
1) Read all instructions provided.
2) Save these instructions for future use.
3) Follow all warnings and instructions marked
on the television equipment.
4) Never insert objects of any kind into this
television monitor through cabinet slots as
they may come in contact with dangerous
voltage points or short out parts, resulting in
fire or electric hazards, Never spill liquid of
any kind on the television monitor.
5) Do not attempt to service this television
monitor yourself as operating or removing
covers many expose you to dangerous voltage
or other hazards, Refer all servicing to
qualified service personnel.
6) Do not use attachments not recommended by
the television equipment manufacturer as they
may result in the risk of fire, electric shock, or
injury to persons.
7) This television monitor has been preadjusted
to meet the respective broadcasting standard
signals. So, it cannot be used with the signals
of different broadcasting standards.
8) When keeping or transporting the unit for a
long time, pack it in the supplied carton or
equivalent.
2. Power supply
1) This television equipment should be operated
only from the type of power source indicated on
the marking label.
2) This television equipment is provided with a
three-wire grounding type plug with a third
(grounding) pin. This plug will only fit into a
grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug
into the outlet, contact your electrician to
replace your obsolete outlet.
Do not defeat the safety purpose of the
grounding-type plug.
3) When connecting and disconnecting the
power cable, be sure to hold the plug.
4) Do not allow anything to rest on the power
cord. Do not place this television equipment
where the cord will be abused by persons
walking on it.
5) For added protection for this television
equipment during a lightning storm, or when
it is left unattended and unused for long
periods of time, unplug it from the wall outlet.
This will prevent damage to the equipment
due to lightning and power-line surges.
6) Do not overload wall outlets and extension
cords as this can result in fire or electric shock.
3. Usage and location
1) Do not use this television equipment near
water - for example, near a bath tub,
kitchen sink, or laundry tub, in a wet basement,
or near a swimming pool, or the like.
2) Do not place this television equipment on an
unstable cart, stand, or table. The television
equipment may fall, causing serious injury to
children and adults, and serious damage to the
equipment. Use only with a cart or stand
recommended by the manufacture, or sold
with the television equipment. Wall or shelf
mounting should follow the manufacture’s
instructions, and should use a mounting kit
approved by the manufacture.
Television equipment and cart combination
should be moved with care. Quick stops,
excessive force, and uneven
surfaces may cause the
equipment and cart
combination to overturn.

3) Slots and openings in the cabinet and the back
or bottom are provided for vitiation, and to
ensure reliable operation of the monitor and
to protect it from overheating, these openings
should never be blocked or covered. The openings
should never be blocked by placing the
television equipment on a bed, sofa, rug, or
other similar surface. (This television
equipment should never be placed near or
over a radiator or heat register.)
This television equipment monitor should not
be placed in a built-in installation such as a
bookcase unless proper ventilation is
provided.
4) Avoid operating or placing (keeping) in a hot
(+40ºC or over) or cold (less than 0ºC), high
vibration, or dusty place. Avoid operating or placing
(keeping) in a place exposed to direct sunlight,
otherwise the CRT surface may deteriorate.
5) If an image of extremely high brightness is
displayed on the screen for a long time, the
CRT may get burned in.
4. Cleaning
1) Unplug this television equipment from the
wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
2) Do not use thinner or benzine for cleaning.
Otherwise, the cabinet may deform or the
paint may peel away.
IMPORTANT SAFETY INSTRUCTION
5. Repair
1) Unplug this television monitor from the wall
outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power cord or plug is damaged
or frayed.
b. If liquid has been spilled into the
television.
c. If the television monitor has been exposed
to rain or water.
d. If the television does not operate normally
by following the operating instructions.
Adjust only those controls that are
covered by the operating instructions as
improper adjustment of other controls may
result in damage and will often require
extensive work by a qualified technician
to restore the television monitor to normal
operation.
e. If the television monitor has been dropped
or the cabinet has been damaged.
f. When the monitor exhibits a distinct
change in performance - this indicates a
need for service.
2) When replacement parts are required, be sure
the service technician has used replacement
parts specified by the manufacture that have
the same characteristics as the original part.
Unauthorized substitutions may result in fire.
Electric shock, or injury to persons.
3) Upon completion of any service or repairs to
this monitor, ask the service technician to
perform routine safety checks to determine
that the television is in safe operating
condition.
4) For repair service, contact Ikegami’s
authorized sales representative or Ikegami
service desk directly.

PRECAUTIONS FOR OPERATIONS
1) Never let this unit fall or subject it to strong
shock.
2) Do not remove the cabinet unless necessary.
High-voltage parts are contained in the
cabinet and they are very dangerous if you
touch then. Only qualified service engineers
are allowed to adjust the internal parts of the
cabinet.
3) This color monitor has been adjusted to
signals conforming to each broadcasting
standard.
It cannot be used for signals of different
broadcasting standards.
Be sure to operate the color monitor within
the voltage range marked on its back.
4) If cabinet or screen is dirty, wipe with soft
cloth. At this time, avoid using benzine or
thinner.
Otherwise, the paint may peel away.
5) Note that, if video signals with high
luminance are monitored on the CRT over a
long period of time, the CRT may burn in the
image.
6) Avoid using or storing this unit in the
following places:
•Hot (+40ºC or more) or cold (0ºC or less)
places.
Especially where this unit may be exposed
to the direct rays of the sun; the cabinet
may deform and the fluorescent screen of
the CRT may deteriorate.
•Humid and dusty places.
•Places where there is considerable
vibration.
• Places exposed to rain or water.
•When storing or transporting this unit, pack it
in the supplied carton or equivalent.
7) If no image can be monitored even after
performing user adjustment or the unit
appears faulty, do not dismantle this unit by
yourself. In such cases, contact the Ikegami
service desk.
8) Should this unit fail within one year after
delivery, it will be repaired free of charge
unless the malfunction was caused by
mishandling or misuse of the user.
However, the fuses are not covered
by the warranty.
9) The specifications and appearance of this unit
may be subject to change for further
improvement without prior notice.

Fan alarm
If the built-in fan is interrupted, the POWER LED starts
blinking and the following message appears on screen. In
this case, immediately turn OFF the power and contact the
nearest Ikegami dealer.
This message disappears 2 minutes later. The POWER
LED still blinks 8 times in 2 seconds and remains off for 1
second repeatedly and the high-tension section shuts down
itself. If no image is displayed on screen but the POWER
LED is blinking, therefore, immediately turn OFF the power.
Precautions Upon Use
To ensure safe use of this monitor, read this manual carefully, paying particular attention to
the following items.
1. Do not use any power supply other than the regulation AC power.
2. Do not subjecting the monitor to strong impact.
Otherwise, it will result not only in malfunction, but explosion of the CRT as well.
3. Avoid use and storage in the following places.
*Locations which do not meet the designated ambient temperature
installing the monitor near equipment generating heat or in cabinets with closed vents
causes the internal temperature of the monitor rise, which not only reduces the life of the
electrical parts but also causes malfunction.
*Locations with rain, snow, or excess humidity
Locationing the monitor in the above conditions will cause malfunction.
*Strong magnetic fields
4. Avoid exposing the CRT to sunlight
Subjecting the CRT to direct sunlight for a long period of time deteriorates the florescent
faces of the CRT. So avoid use outdoors.
5. Avoid exposing to high luminance fixed image for long periods of time
Take care as this will cause burn in of the CRT.
Also avoid displaying remote numbers in the remote entry state (remote numbers are displayed
when the wireless remote controller is used) for long periods of time. When not using the
wireless controller, set the remote number displayed on the screen to OFF.
Guarantee
Malfunctions occurring in normal use within one year from the date of purchase will be repaired
free of charge. This does not apply to the fuses.
If no image is displayed after user adjustment or if malfunction is suspected, contact your nearest
Ikegami dealer.
Accessories
This monitor is provided with the following accessories.
Check that none is missing.
1. Operation manual
2. AC cable
3. Remote connector
* Specifications and external dimensions are subject to change without prior notice.
CAUTION
WARNING:
FAN STOPPED !!
<POWER OFF PLEASE>
CAUTION
Battery alarm (AC/DC input type)
• External battery
If the DC voltage to the monitor drops below DC 10.8V
on the battery power, the POWER LED starts blinking (on
and off repeatedly) to warn of a battery shortage. In this
case, immediately turn OFF the power and replace the
battery with a fully charged one.
• Memory backup battery in the monitor
As the memory backup battery becomes low in voltage,
“CHANGE BATTERY” appears on screen when the power
is turned ON. In this case, immediately turn OFF the power
and contact the nearest Ikegami dealer.
If the battery becomes dead, various adjustment data
may be erased. You will have to make these adjustments
every time the power is turned on.

CONTENTS
IMPORTANT SAFETY INSTRUCTION
PRECAUTIONS FOR OPERATIONS
1. General ............................................................ 1
1.1 General ........................................................ 1
1.2 Features ....................................................... 1
2. Specifications ................................................. 3
2.1 Common specifications ................................ 3
(1) General ........................................................... 3
(2) Video signal system ....................................... 3
(3) Brightness and contrast .................................. 3
(4) Deflection/sync system .................................. 3
(5) Function ......................................................... 4
(6) Memory .......................................................... 4
(7) Applicable standards ...................................... 4
2.2 Individual specifications ............................... 4
(1) YPbPr/RGB input module
(mounted as standard) .................................... 4
(2) MULTI-SDI input module (option) ............... 5
(3) Embedded audio level meter display module
(option) .......................................................... 6
(4) SD-SDI input module (option) ...................... 6
(5) Decoder input module (option) ...................... 6
2.3 Option .......................................................... 6
2.4 List of Optional Module Combinations ......... 7
2.5 External View ............................................... 8
(1) HTM-1005R ................................................. 8
(2) HTM-1005R with DAM-1054/1058 ............. 9
3. Installation ..................................................... 10
3.1 External connection ................................... 10
(1) Standard module .......................................... 10
(2)-1 MULTI-SDI module
(DKM-1051) option ................................... 11
(2)-2 MULTI-SDI module
(DKM-1051AV) option ............................. 11
(2)-3 MULTI-SDI module
(DKM-1051AVD) option ......................... 12
(3) SD-SDI module (DK-1051, DK1052N,
DK-10512, DEK-1052N) option ................. 12
(4)-1 NTSC/PAL decoder module
(DE-1051) option ...................................... 13
(4)-2 NTSC serial digital composite &
decoder module (DEK-1052N) option ..... 13
(5) YPbPr/RGB input module
(DCH-1051) option ...................................... 14
3.2 Parallel remote connection ........................ 15
(1) Pin function .................................................. 15
(2) Connector (standard accessory) ................... 15
3.3 Power supply ............................................. 16
(1) AC input type ............................................... 16
(2) AC/DC input type ........................................ 16
4. User adjustment ............................................ 17
4.1 Names and functions of front panel parts .. 17
4.2 Description of preset data manipulation .... 20
(1) Switch operation during presetting .............. 20
(2) Description of preset data ............................ 20
4.3 Procedures for registering data
in memory or changing data ...................... 22
(1) Registering/changing PRESET data ............ 22
(2) File data registration or change .................... 23
4.4 Adjustment procedures .............................. 23
(1) Brightness adjustment .................................. 23
(2) Contrast adjustment ..................................... 23
(3) White balance adjustment ............................ 24
(4) Color balance adjustment ............................ 25
(5) Screen center adjustment ............................. 26
(6) Screen distortion adjustment ........................ 27
(7) Screen size adjustment ................................. 28
4.5 Menu functions .......................................... 30
(1) Menu list ...................................................... 30
(2) Menu operational flowchart ......................... 31
(3) Description of MENU 1 functions ............... 32
(4) Description of MENU 2 functions ............... 32
(5) Description of MENU 3 functions ............... 33
(6) Description of MENU 4 functions ............... 34
(7) Description of MENU 5 functions ............... 34
(8) Description of MENU 6 functions ............... 34
(9) Description of MENU 7 functions ............... 35
4.6 Description of screen messages................ 36
5. Installation and removal of options............. 37
5.1
Installation procedures, installation examples and
removal procedures for optional modules ....... 37
6. Rack mount installation drawing ................. 38
(1) XRM-744 installation drawing .................... 38
(2) XRM-754 installation drawing .................... 39
(3) RM-HTM-001 installation drawing ............. 40
7. Memo .............................................................. 41

1
1. General
1.1 General
This monitor is a 10-inch type HDTV/SDTV multi format color
monitor. It is designed for use in various spaces such as a studio
control room, edit/monitor rack, send-out control desk and field
pick-up van, taking each HDTV format and use in combination
with SDTV into account.
A newly developed SDI module supports multi format input and
an embedded audio-compatible type is also available. The
embedded audio type has versatile functions such as “analog or
AES/EBU output”, “sound output from speakers” and “audio level
meter display”. The monitoring of videos and voices can be realized
on a single monitor. This monitor is excellent in space factors.
1.2 Features
(1) Multi format-compatible
Various broadcasting formats are supported as shown below.
[HDTV (including options)]
• 1080i/60, 59.94 SMPTE 274M
• 1080i/50 SMPTE 274M
• 1035i/60, 59.94 SMPTE 240M, BTA S-001B
• 720p/60, 59.94 SMPTE 296M
• 1080i/48, 47.95 SMPTE RP211
[SDTV (Including options)]
• 525i (NTSC) ITU-601
• 625i (PAL-B) ITU-601
The standard analog YPbPr/RGB input is compatible with the
following formats.
The HDTV field frequency is 59.94/60Hz.
The HDTV frequency 50 Hz/48 Hz is optionally supported.
(2) Multi format SDI-compatible
An optional multi format-compatible SDI module (DKM-1051/AV/
AVD) is capable of accepting HD-SDI signals or SD-SDI (4:2:2)
signals without discrimination through a single input terminal.
The inputted HD-SDI signals or SD-SDI (4:2:2) signals are
automatically identified on the monitor side and displayed in an
appropriate format.
(3) Embedded audio output-compatible
An optional embedded audio-compatible multi format SDI module
(DKM 1051AV/AVD), which is equipped with a demultiplexer
circuit for extracting HD-SDI signal- or SD-SDI (4:2:2) signal-
multiplexed audio signals, can output audio signals.
The audio output is available in two types, AV and AVD. The former
outputs two channels of analog audio signals (channel switching is
done by menu-setting) and the latter outputs eight channels in the
AES/EBU format. You can also hear embedded audio voices from
the standard speaker.
(4) Embedded audio-compatible audio level meter
The employment of an optional embedded audio-compatible audio
level meter (DAM-1054/1058) realizes the simultaneous monitoring
of both video signals and audio signals through a single cable only.
The level meter is an LED excellent in visibility. This meter does
not need any new space, unlike other signal-superimposed types
where there is a fear of CRT burn-in markings, since it is mounted
on the front of the main unit escutcheon.
(DKM-1051AV/AVD is needed.)
(5) Remote control functions
Three types of remote control are available. The remote controllers
for parallel remote and serial remote modes can be used selectively
according to the installation area or intended operation.
In addition to the conventional parallel remote control, mounted as
standard is a serial remote input interface capable of remote
controlling through a single BNC coaxial cable. The use of a serial
remote controller SRC 301A (option) makes it possible to remote
control up to 99 monitors individually simply by making loop
through connections between monitors (e.g. 17/18/20/30/80/90/
HTM series monitors).
(6) Digital control
Each digital data is 10 bit-processed. The employment of an up-
and-down method makes it easy to make a data change adjustment.
A screen size, screen position, side pin correction and keystone
distortion correction are also remote controllable and therefore
various types of signal formats can be flexibly supported.
(7) Memorizing four types of color temperatures
In addition to the factory-set color temperature D93/D65, another
type of color temperature can be memorized, so that the optimum
white balance can also be selected quickly and easily according to
the state of input video images or intended use.
HTM-1005R/RA Multi-Format Color MonitorHTM-1005R/RA Multi-Format Color Monitor
HTM-1005R1
HTM-1005R2
525i/59.94 1035i 1080i 720p625i/50
SDTV HDTV

2
(8) BFS (Beam Feedback System)
The employment of a BFS circuit designed to detect the CRT
cathode current provides a steady black balance for a long time
against variations in CRT emission.
(9) NTSC/PAL decoder
An optional decoder module DE-1051 supports both the NTSC and
PAL-B systems and has the function of automatic discrimination.
Also, an optional DEK-1052N, which has two NTSC/PAL analog
composite inputs and two SD-SDI digital component (NTSC) inputs
in a single slot, can be used in conjunction with an HD-SDI module.
(10) Various built-in markers
At the time of the display of 16:9, the 4:3, 13:9 or 14:9 marker-
display is possible.
For the aspects 4:3 and 16:9, respectively, the 80%, 88%, 90%,
93%, 100% and other versatile markers can be displayed.
(11) Degaussing timer function
The degaussing function designed to be enabled automatically at
monitor power-on is set (at the factory) in such a way that it starts
approximately 10 seconds after power-on through the use of a timer.
On the menu, this timer can be set for 10 to 14.5 seconds in steps of
0.5 second for each monitor on an individual basis.
This makes it possible to minimize the rush current that will flow
in systems equipped with many monitors if the power to them is
turned on at the same time.
(12) Construction designed with emphasis placed
on maintainability and expendability
The modules in the signal processing system, including optional
modules, which are of the plug-in type that is easy to insert and
extract from the rear without removing the cover, are easy to
maintain.
Besides the standard VEDEO PROCESS module (HDTV/SDTV
YPbPr/RGB), up to two types of optional modules can be added
for expansion.
(13) Employment of high performance in-line gun
CRT
The employment of a high performance and high precision CRT
equipped with an in-line gun, dot mask and mask pitch: 0.28 mm
reduces the reflection of external light. The use of a CRT shadow
mask improves remarkably the dooming (beam deflection caused
by a thermal distortion of the shadow mask) that occurs when the
brightness is increased.
(14) Brightness correction function in each screen
size
For a CRT monitor, the current density will increase if the screen
size is reduced as in the case where the scan changes from the normal
mode to under mode or from 4:3 to 16:9. The brightness of a general
monitor will increase by approximately 40% when the scan changes
to 4:3 to 16:9. Therefore, video images will also change when the
switching between aspect ratios is done. This monitor makes a
brightness correction in four screen sizes respectively so that the
brightness will be held constant even when the screen size changes.
(15) HD 4:3 scan function
For the HDTV input, this monitor has the function of allowing the
4:3 area video images only to fill the screen frame (4:3) and the
images can be monitored in real time at the time of down-conversion
to SDTV 4:3 during HDTV recording.
(16) High performance high-voltage regulation
circuit
The high-voltage circuit, which employs a regulation circuit for
controlling pulses on a scanning line-by-scanning line basis, has a
high response speed and realizes highly stable images with the
distortion of bright video image input on the screen minimized.
(17) Auto setup function
The use of an optional auto setup probe ASP-80 allows an automatic
adjustment to the factory-set color temperatures with ease.
If the operator’s own color temperature is set, any number of
monitors can be adjusted to the same color temperature
automatically.
(18) Lower power consumption (AC input-only type)
As compared with the conventional HTM-1005R, the HTM-
1005RA is designed as standard specifically for AC input and an
extra DC input circuit is omitted, so that the power consumption is
reduced by approximately 15%.
The AC-input-only type is selectable between 100 VAC and 240
VAC and therefore suitable for overseas or worldwide use.
* The AC/DC input type is not designed to the specifications above.

3
2. Specifications
2.1 Common specifications
(1) General
1. Power supply
a) AC-only type (standard)
AC, single-phase, 50/60 Hz
100 V to 240 V ±10%
Power consumption: Approx. 95 W
b) AC/DC type (for use of optional DAC1051)
AC, single-phase, 50/60 Hz
100 V area: 100 V to 120 V ±10%
200 V area: 200 V to 240 V ±10%
Power consumption: Approx. 120 W
DC: 12 V ±10%
Power consumption: Approx. 100 W
* The power consumption above is at maximum load with full
options installed.
2. Ambient temperature
0°C to +40°C
3. Humidity
90% or less (no condensation)
4. Outside dimensions/mass
222 (W) x 213 (H) x 415 (D) mm
Approx. 10 kg
5. Standard accessories
Power cable, remote connector, operation manual ... 1 set, each
6. Use
Continuous
7. X-ray radiation
0.1 mR/H or less
(in all areas 50 mm away from the outside of the monitor)
(2) Video signal system
1. Frequency response
a) HDTV (YPbPr/RGB input)
60 Hz to 17 MHz: +1/-3dB
17 MHz or higher: Downward characteristics
b) SDTV (Composite input)
60 Hz to 7 MHz: +1/-3dB
7 MHz or higher: Downward characteristics
2. Sag
Within 5%
3. Black level stability
Within 1% against a change of APL 10% to 90%
4. Aperture correction
+6 dB or more is variable at the following frequencies.
a) HDTV
10 MHz ±2.5 MHz
b) SDTV (for use of DE-1051)
5 MHz ±1 MHz
* No effect on the RGB input digital component or SDTV YPbPr
input
5. Noise
Sync noise: -40 dB or less
Hum noise: -40 dB or less
Others: -40 dB or less
(3) Brightness and contrast
1. CRT
Dot trio pitch: 0.28 mm
2. Horizontal resolution
500 lines or more (HDTV) when the value in the screen center
is 120 cd/m2(35 fl) for YPbPr input
3. Preset contrast
Factory-set value: 120 cd/m2(35 fl)
4. Maximum brightness
200 cd/m2 or more
(100% window signal input, Brightness: PRESET,
Contrast: MAX)
(4) Deflection/sync system
1. 16:9 display size
a) NORMAL: W174 x H98 mm
b) UNDER: W160 x H90 mm
2. Deflection
a) NORMAL SCAN (4:3/16:9)
b) UNDER SCAN (4:3/16:9)
3. Deflection distortion
Within ±1% of screen height
(Deflection linearity and raster distortion)
4. Sync stability
Steady operation is provided when the input signal is within the
range below.
Internal sync: Video input level rated value ±6 dB
External sync: External sync input level 0.3 to 6 Vp-p
5. High voltage
Generated high voltage: 19 kV ±1 kV
High voltage fluctuation: Within ±0.5% when the beam current
is in the range 0 to 300 µA
(Reference: 100 µA)
6. Convergence
90% area of screen height: Within 0.4 mm
90% area of screen width: Within 0.5 mm

4
(5) Function
1. Marker function
a) Center marker
The ON/OFF setting is made on the menu.
b) Safe title
The following markers are displayed according to the aspect
ratio (4:3/16:9).
The numerals inside the parentheses are aspect ratios at the
time of marker display.
Type
• 80% + 100% (4:3/16:9)
• 88% + 100% (4:3/16:9)
• 90% + 100% (4:3/16:9)
• 93% + 100% (4:3/16:9)
• 5 divided crosshatch (4:3/16:9)
• 10 divided crosshatch (4:3/16:9)
• Cross (4:3/16:9)
• 14:9 100% area (16:9)
• 13:9 100% area (16:9)
• 4:3 marker (16:9)
• 4:3 marker + 80% (4:3) marker (16:9)
2. Remote control
a) Parallel remote control
Channel COMPOSITE/AUX/HD-SDI/SD-SDI, RGB/YPbPr,
COLOR/MONO, SYNC INT/EXT, 4:3/16:9, 4:3 MARKER
ON/OFF, R/G TALLY ON/OFF
b) Serial remote control
The input interface comes standard and almost all monitor
control is possible.
(A controller SRC-301A is optional.)
3. Beam feedback system (BFS)
4. Menu assist
• Input signal format setting
• RGB/YPbPr switching setting
• Marker center cross display ON/OFF setting
• Remote ID number setting
• DEGAUSS timer setting
• Each preset data % display
• Password setting
(6) Memory
1. Memory type
ROM: 64-Kbyte programmable ROM
RAM: 32-Kbyte static RAM
2. Battery/Backup
Hold time of memory: 10 years or more
Battery: Lithium battery (BR2330-1HF)
(7) Applicable standards
1. Safety standards
Compliant with UL1950
2. Electromagnetic interference
FCC Class-A
3. X-ray radiation
DHHS
2.2 Individual specifications
Standard specifications: YPbPr/RGB 1-input module only
(1) YPbPr/RGB input module (mounted as standard)
• YPbPr/RGB 1-input module
• DCH-1051 dual component module
(Optional module for YPbPr/RGB 1-input expansion)
1. Input/Output terminal
a) YPbPr/RGB 1-input module (standard)
YPbPr/RGB: BNC 1 line (loop through)
Sync input: BNC 1 line (loop through)
Audio input: RCA 1 line
b) DCH-1051 (for YPbPr/RGB 1-input expansion)
YPbPr/RGB: BNC 1 line (loop through)
2. Input signal format (YPbPr/RGB)
a) SDTV
• 525i/59.94
• 625i/50
b) HDTV
• 1035i/60, 59.94
• 1080i/60, 59.94
• 1080i/50 (option)
• 1080i/48, 47.95 (option)
• 720p/60, 59.94 (HTM-1005R1 type)
3. Input level
a) HDTV (BTA S-001B)
• Y, G, B, R input V: 700 mVp-p, positive polarity
S: ±300 mVp-p
• Pb, Pr input V: ±350 mVp-p, positive polarity
• Sync input: ±300 mVp-p
b) SDTV (SMPTE/EBU N10)
• RGB input VS: 1.0 Vp-p, positive polarity
V: 0.7 Vp-p, positive polarity
VS: A sync signal is added to R, G and B,
respectively.
A sync signal is added to G only.
V: R, G and B have no sync signal,
respectively.
• YPbPr input: Positive polarity
Y signal WHITE: 700 mVp-p
SET UP: 0 mVp-p
SYNC: 300 mVp-p
PbPr signal: 525 mVp-p
(100/0/75/0 COLOR BAR)
• Sync input : 0.3 V to 6 Vp-p, negative polarity
c) AUDIO: 316 mV (-10 dBV)

5
4. Input impedance
High impedance bridge connection or 75 Ωtermination
(The 75 Ωterminating plug is optional.)
5. Return loss
46 dB or more (10 MHz)
(2) MULTI-SDI input module (option)
• DKM-1051 (multi SDI module)
• DKM-1051AV
(Compatible with embedded analog audio output)
• DKM-1051AVD
(Compatible with embedded AES/EBU output)
[SDI common specifications]
1. Input/Output terminal
a) DKM-1051
Input: BNC 2 lines (active loop through)
Output: BNC 1 line
(The active through is used for one selected output
only.)
2. Input signal format (auto recognition)
SMPTE259M: 480i/59.94 (4:2:2)
576i/50 (4:2:2)
SMPTE292M: 1035i/60, 59.94
1080i/60, 59,94
720p/60, 59.94 (type 1 only.)
1080i/50
(Only when supported by the monitor)
1080i/48, 47.95
(Only when supported by the monitor)
Format switching: Auto switching
3. Input level
Rating 800 mVp-p ±10%
4. Transmission rate
HD-SDI: 1.485 Gb/s
SD-SDI (4:2:2): 270 Mb/s
5. Quantization bit rate
10 bits
6. Input/Output impedance
75 Ω
7. Return loss
a) HD-SDI: 15 dB or more (5 MHz-1/2 fc)
10 dB or more (1/2 fc-fc)
b) SD-SDI (4:2:2): 15 dB or more (270 MHz)
8. Transmission distance
100 m (5 CFB, 1.485 Gb/s)
[Audio signal system specifications]
1. Embedded audio common specifications
• Embedded audio input-compatible format
SMPTE272M: 480i/59.94 (4:2:2)
576i/50 (4:2:2)
SMPTE299M: 1035i/60, 59.94
1080i/60, 59.94
1080i/50
1080i/48, 47.95
720p/60, 59.94
* The embedded audio output is compatible with all formats
even when the monitor main unit is not necessarily
compatible with all formats.
• Format switching: Auto switching
• Sampling frequency: 48 kHz (sync with video clock)
2. Analog audio output (AV type)
• Output connector: XLR-5-32 type
(Canon 5-pin male) x 1
• Line output: Analog audio
2 channels
Select ch1/2, ch3/4, ch5/6 or ch7/8 from the menu.
Active (transformless) balanced output type
• Rated output level: +4 dBs
* Load impedance 10 kΩ
(digital audio level –20 dBFS)
• Maximum output level: +24 dBs
* Load impedance 10 kΩ
(digital audio level 0 dBFS)
• Output impedance: 50 Ω
• Minimum load impedance: 600 Ω
• D/A converter: 128-times over sampling
8-times digital filter
• Quantization bit rate: 24 bits/ch
• Emphasis: 50/15 µs
Digital emphasis
(auto discrimination)
• Frequency response: 20 to 20 kHz ±1 dB
• S/N ratio: 80 dB or more
• Dynamic range: 80 dB or more
• Cross talk: 60 dB or more
(1 kHz, maximum output)
• Total harmonic distortion: 0.1% or less (rated output)
* Analog audio level: 0 dBs = 0.775 Vrms
3. AES/EBU output section (AVD type)
• Output connector: BNC pair channel x 4
Channel (ch1 to ch8) output: (group 1, 2)
• Output standards: AES/EBU standards
(for monitor)
• Output impedance: 75 Ω
* Digital audio level: 0 dBFS = Full bits/full scale

6
4. Speaker output section
Embedded audio voices can also be output from the standard
speaker.
• Number of speakers: 1 channel (standard)
• Output setting
The voices from the speaker are output in three ways, odd,
even/odd and even pair channels (ch1/2, ch3/4, ch5/6, ch7/
8) selected on the menu.
• Analog/digital switching
Whether to output the embedded audio input or standard
analog audio input as the voices from the speaker can be set
on the MENU.
(3) Embedded audio level meter display
module (option)
• Embedded audio input-compatible format
SMPTE272M: 480i/59.94 (4:2:2)
576i/50 (4:2:2)
SMPTE299M: 1035i/60, 59.94
1080i/60, 59.94
1080i/50
1080i/48, 47.95
720p/60, 59.94
* The embedded audio output is compatible with all formats
even when the monitor main unit is not necessarily
compatible with all formats.
• Format switching: Auto switching
• Reference level: -20 dBFS
• Display segment: 13 segments
• Display level: -∞, -60, -50, -40, -35, -30, -25, -20, -16,
-12, -8, -4, 0 dB
• Display device: -∞to -25 dB:Green LED
-20 to 0 dB: Amber LED
• Display panel size: 209 (W) x 22 (H) x 6 (D)
(4) SD-SDI input module (option)
• DK-1051 (4:2:2 digital component module)
• DK-1052N (4Fsc NTSC digital composite module)
• DK-10512 (4:2:2/4Fsc digital module)
• DEK-1052N (4Fsc digital, NTSC/PAL decoder module)
The simultaneous mounting of the four types of modules
above is impossible.
To input digital composite signal using DK-1052N/10512, a
decoder (DE-1051) is required.
1. Input/Output terminal
BNC 2 lines (active loop through)
It is also possible to output the signal linked to a channel selected
on the monitor side by making the setting on the module.
2. Input signal format
a) DK-1051
SDI 4:2:2 digital component signal (525i/59.94, 625i/50)
b) DK-1052N
SDI 4Fsc digital composite signal (NTSC)
c) DK-10512
Compatible with both formats in a) and b)
d) DEK-1052N (SDI input section)
SDI 4Fsc digital composite signal (NTSC)
3. Input/Output level
Rating 800 mVp-p ±10% (output level is at 75 Ωtermination.)
SCRAMBLED NRZI system
4. Transmission rate
DK-1051: 270Mb/s
DK-1052N, DEK-1052N: 143Mb/s
DK-10512: 143Mb/s, 270Mb/s
5. Quantization bit rate
10 bits
6. Input/Output impedance
75 Ω
7. Return loss
15 dB or more (270 MHz)
(5) Decoder input module (option)
• DE-1051 NTSC/PAL decoder module
• DEK-1052N (4Fsc digital, NTSC/PAL decoder module)
(analog composite input section)
1. Input/Output terminal
BNC 2 systems (loop through)
2. Signal format
NTSC/PAL composite signal
3. Input level
VS: 1.0 Vp-p, positive polarity
V: 0.7 Vp-p, positive polarity
4. Input impedance
High impedance bridge connection or 75 Ωtermination
(The 75 Ωterminating plug is optional.)
5. Return loss
46 dB or more (6 MHz)
2.3 Option
1. DKM-1051
HD-SDI/SD-SDI (4:2:2) multi SDI 2-input module
2. DKM-1051AV
Embedded analog 2-channel output-compatible multi SDI 2-
input module
3. DKM-1051AVD
Embedded AES/EBU 8-channel output-compatible multi SDI
2-input module
4. DK-1051
SD-SDI (4:2:2) digital component 2-input module (not
compatible with embedded mode)
5. DK-1052N
SD-SDI 4Fsc NTSC digital composite 2-input module (DE-
1051 is required. Not compatible with embedded mode)

7
6. DEK-1052N
(It is impossible to mount this module in conjunction with
DKM-1051* simultaneously.)
4-input module designed to mount DK-1052N and DE-1051 in
a single slot
SD-SDI NTSC digital composite 2-input
NTSC/PAL analog composite 2-input
(Not compatible with embedded mode)
7. DAM-1054
4-ch embedded audio level meter display module (DKM-
1051AV/AVD is required.)
8. DAM-1058
8-ch embedded audio level meter display module (DKM-
1051AV/AVD is required.)
9. DE-1051
NTSC/PAL analog composite 2-input module
10. DCH-1051
YPbPr/RGB input module for 1-input expansion
11. SRC-301A
Serial remote controller
12. ASP-80
Auto setup probe
Auto adjustments of color temperatures
13. BR-1050
Battery adapter for BP-90
14. BR-1050L
Lithium ion battery adapter for BP-L90A
(BP-L90A is diverted to this purpose in terms of capacity.)
15. EX-1051A
Extender board for adjustment
16. ADC-1051 (factory option)
AC/DC module (built to AC/DC power supply specifications)
* When a module designed to AC/DC power supply
specifications is necessary, it must be required when an order
is placed, since a standard one is designed specifically for
AC use.
17. XRM-744
Rack mount adapter for two main units
18. XRM-754
Rack mount adapter for one main unit
(One main unit + Blank panel)
19. RM-HTM-001
Rack mount adapter for one main unit + one WFM
* For a Tektronix-made WFM700HD/A/M, use RM-HTM-002.
20. RM-HTM-002
Rack mount adapter for one main unit + one WFM (Tektronix-
made WFM700HD/A/M)
21. SC-1050
Soft carrying case
22. CC-1050
Hard carrying case
The specifications and appearance are subject to change without
prior notice for improvements.
DKM-1051
DKM-1051
DKM-1051AV
DKM-1051AV
+
DAM-1054
DKM-1051AV
+
DAM-1058
DKM-1051AVD
DKM-1051AVD
+
DAM-1054
DKM-1051AVD
+
DAM-1058
DK-1051
DK-1052N
DK-10512
DEK-1052N
DE-1051
DCH-1051
DKM-1051AV
DKM-1051AV
+
DAM-1054
DKM-1051AV
+
DAM-1058
DKM-1051AVD
+
DAM-1054
DKM-1051AVD
+
DAM-1058
DKM-1051AVD DK-1051 DK-1052N DK-10512 DEK-1052N DE-1051 DCH-1051

12
(2)-3 MULTI-SDI module (DKM-1051AVD) option
(3) SD-SDI module (DK-1051, DK1052N, DK-10512, DEK-1052N) option
Illustration of DK-1051
MULTI-SDI module (DKM-1051AVD) option
•Input SDI signal here.
•Acceptable input format
 1. 480i / 59.94 (4 : 2 : 2)
 2. 576i / 50 (4 : 2 : 2)
 3. 1035i / 59.94 (60)
 4. 1080i / 59.94 (60)
 5. 1080i / 50 (Option)
 6. 1080i / 47.95 (48) (Option)
 7. 720p / 59.94 (60)
 (The 720p is compatible with HTM-1005R1 only.)
MULTI SDI input
•Eight channels (8-ch) of embedded audio signal superimposed on HD-SDI or SD-SDI signal output in the
 AES/EBU format.
 The output impedance is 75 Ω.
(Caution)For the mounting of this option, refer to "5. Installation and Removal of Options".
 When DAM-1054 or DAM-1058 is mounted, this option can be installed in the "expansion slot
 2 for option" only.
•Of the input SDI signals (A/B ch), the signal on a channel selected on the monitor side output here.
MULTI SDI output
Embedded AES/EBU 8-ch output (0 dBFS)
SD-SDI module (DK-1051, DK1052N, DK-10512, DEK-1052N) option
•The SD-SDI signal input to B-channel output.
•The signal selected on the monitor side can also output here by setting connectors in the module.
•<How to Set>
SD-SDI B (monitor)-output
The SD-SDI modules are available in three types below and the display varies with modules.
•"SDI 4:2:2" 4:2:2 digital component module (DK-1051)
•"SDI 4FscN" NTSC digital composite module (DK-1052N)
•"SDI 4:2:2 4FscN" 4:2:2 digital component & digital composite module (DK-10512N)
Illustration of
DK-1051
•Input SD-SDI signal here according to the following modules, respectively.
•DK-1051 4:2:2 serial digital component signal
•DK-1052N NTSC serial digital composite signal
•DK-10512 4:2:2 digital component, NTSC digital composite signal
 (The formats are detected automatically.)
SD-SDI A/B input
•The SD-SDI signal input to A-channel output here. (Active loop through)
SD-SDI A-output
NORMAL(Factory-set)
EL102EL101
MONITOR OUT
EL102EL101

13
(4)-1 NTSC/PAL decoder module (DE-1051) option
(4)-2 NTSC serial digital composite & decoder module (DEK-1052N) option
NTSC/PAL decoder module (DE-1051) option
•Input NTSC/PAL signal.
•Acceptable input format
 1. 480i / 59.94 (NTSC)
 2. 576i / 50 (PAL)
•When loop through connections are not used, terminate with a terminating plug.
•When using external synchronization, input an external synchronizing signal to the external sync signal
 input on the VIDEO PROCESS module.
Analog composite input
NTSC serial digital composite & decoder module (DEK-1052N) option
•The SD-SDI signal input to B-channel output.
•The signal selected on the monitor side can also output here by setting switches in the module.
•<How to Set>
SD-SDI B (monitor)-output
•Input 4Fsc NTSC digital composite signal.
SD-SDI A/B input
NORMAL(Factory-set)
S101S102
MONITOR OUT
S101S102
•Input NTSC/PAL signal.
•Acceptable input format
 1. 480i / 59.94 (NTSC)
 2. 576i / 50 (PAL)
•When loop through connections are not used, terminate with a terminating plug.
•When using external synchronization, input an external synchronizing signal to the external sync signal
 input on the VIDEO PROCESS module.
Analog composite input
SD-SDI A-output
•The SD-SDI signal input to A-channel output from here. (Active loop through)

14
(5) YPbPr/RGB input module (DCH-1051) option
YPbPr/RGB input module (DCH-1051) option
•Input YPbPr signals or RGB signals.
•Acceptable input format
 1. 480i / 59.94
 2. 576i / 50
 3. 1035i / 59.94 (60)
 4. 1080i / 59.94 (60)
 5. 720p / 59.94 (60) (The 720p is compatible with HTM-1005R1 only.)
 6. 1080i / 47.95 (48) (Optionally supported)
 7. 1080i / 50 (Optionally supported)
•To set signal formats, the menu item 1-2 HDTV/SDTV must be set.
•For 1035i and 1080i/59.94 (60), either of them must be selected from the menu item 1-3.
•The YPbPr/RGB switching is done using the menu item 1-4.
•When loop through connections are not used, connect a terminating plug.
•The use of this option makes it possible to input two channels of YPbPr/RGB signals.
YPbPr/RGB input

15
3.2 Parallel remote connection
(1) Pin function
(2) Connector (standard accessory)
D sub 15-pin (male) mini-type connector
• HDB-15M (3011-15) Japan Aviation Electronics Industry-made
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
GND
CH-B on
N.C
G TALLY on
RGB/YPbPr on
SD-SDI on
MONO on
RGB on
EXT-SYNC on
16:9 on
N.C
MARKER on
N.C
R TALLY on
HD-SDI/
Multi-SDI on
Connecting each remote terminal to Pin 1 allows
On-control.
Connect to Pin 1 to select the B-channel at the time of
analog composite, SD-SDI, HD-SDI input.
* If both Pin 2 and Pin 3 are open, the A-channel will be
selected.
Free terminal
Connect to Pin 1 to turn on G TALLY.
Connect to Pin 1 to select the RGB/YPbPr input.
For the A/B switching, Pin 2 is used at the same time.
* If Pin 5, Pin 6 and Pin 15 are open when DE-1051 is
mounted, analog composites will be selected.
Connect to Pin 1 to select the SD-SDI input module.
For the A/B switching, Pin 2 is used at the same time.
* If Pin 5, Pin 6 and Pin 15 are open when DE-1051 is
mounted, analog composites will be selected.
Connect to Pin 1 to set COLOR/MONO to MONO.
Connect Pin 1 to set the RGB/YPbPr mode to RGB
when the RGB/YPbPr input is selected.
Connect Pin 1 to set the sync of analog input to
external synchronization (EXT-SYNC).
Connect to Pin 1 to set the aspect ratio (4:3/16:9) of
SDTV signal to 16:9. For HDTV signal, the switching
to 4:3 is done in the HD4:3 SCAN mode.
To perform the channel switching and control at the
same time, set the menu item 2-4 “CHANGE ASP.” to
“MANUAL”.
Free terminal
Connect to Pin 1 to turn on the 4:3 marker.
Free terminal
Connect to Pin 1 to turn on R TALLY.
Connect to Pin 1 to select the HD-SDI/Multi-SDI input
module. For the A/B switching, Pin 2 is used at the
same time.
* If Pin 5, Pin 6 and Pin 15 are open when DE-1051 is
mounted, analog composites will be selected.
Pin No. Name Operation
Functions of HTM-1050*/HTM-1005* parallel remote pins
1GND
CH-B on
N.C
G TALLY on
RGB/YPbPr on
SD-SDI on
MONO on
RGB on
EXT-SYNC on
16:9 on
N.C
MARKER on
N.C
R TALLY on
HD-SDI/Multi-SDI on
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Remote connector wiring

16
DC IN 12V
BREAKER 10A
AC IN 100-120V
GND
N.C
N.C
12V
1
1
23
4
2
3
4
If the breaker has been actuated, eliminate the cause prior to pressing in this button.
Breaker (for DC power supply overcurrent protection)
When using DC power to operate monitors, supply 12 V here.
(Caution) <Nickel hydrogen battery>
 For the use of nickel-hydrogen batteries, a parallel connection of two
 or more batteries is possible. Battery makers, however, say that their
 warranty will not cover any products if they are used for monitors or
 lighting equipment, since the lifetime of batteries is shortened in such
 use environments due to the heat generated by the batteries themselves.
 It is therefore not recommendable to use nickel hydrogen batteries for
 this machine.
DC power input
Insert the supplied AC cable here to supply AC power.
AC power input
To prevent the AC plug from falling off, lock the AC plug with this hardware after
insertion.
AC plug retainer
AC IN
Insert the supplied AC cable here to supply AC power.
AC power input
To prevent the AC plug from falling off, lock the AC plug with this hardware after
insertion.
AC plug retainer
3.3 Power supply
(1) AC input type
(2) AC/DC input type