iLive ICB103BU User manual

Plug the included AC/DC power adapter into
the DC POWER INPUT on the dock and
an AC power outlet to power the dock.
USB
CHARGER LINE IN
DC IN 5V
FM ANT
USER’S GUIDE
V: 842-01
ICB103 Bluetooth Speaker with Clock
Warning: Changes or modications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• The apparatus shall not be exposed to dripping or splashing and that no objects lled with
liquids, such as vases, shall be placed on apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux éclaboussures et aucun objet ne
contenant de liquide, tel qu’un vase, ne doit être placé sur l’objet.
• Main plug is used as disconnect device and it should remain readily operable during intended
use. In order to disconnect the apparatus from the mains completely, the mains plug should
be disconnected form the mains socket outlet completely.
La prise du secteur ne doit pas être obstruée ou doit être facilement accessible pendant son
utilisation. Pour être complètement déconnecté de l’alimentation d’entrée, la prise doit être
débranchée du secteur.
• Battery shall not be exposed to excessive heat such as sunshine, re or the like.
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à la lumière du soleil, au feu
ou autres choses de semblable.
• Caution marking is located at the rear or bottom of the apparatus.
Attention marquage est situé sur le paneau arrière ou inférieur de l’unité.
• The marking information is located at the rear or bottom of apparatus.
Le marquage est situé sur le paneau arrière ou inférieur de l’unité.
1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized
or grounding - type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. When the provided plug
does not t into your outlet, consult an electrician
for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories
specied by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table
specied by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury
from tip-over. Unplug this apparatus during lightning
storms or when unused for long periods of time.
13. Refer all servicing to qualied
service personnel. Servicing
is required when the apparatus
has been damaged in any way,
such as power-supply cord or
plug is damaged, liquid has been
spilled or objects have fallen
into the apparatus, the apparatus
has been exposed to rain or
moisture, does not operate
normally, or has been dropped.
• CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
• WARNING:To reduce the risk of re or electric shock, do
not expose this apparatus to rain or moisture.
• AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc
électrique, ne pas exposer cet appareil sous la pluie et l’humidité.
• CAUTION: Use of controls or adjustments or performance of procedures
other than those specied may result in hazardous radiation exposure.
• WARNING: Changes or modications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
• WARNING:Do not place this unit directly onto furniture surfaces with any type of soft, porous,
or sensitive nish. As with any rubber compound made with oils, the feet could cause marks
or staining where the feet reside. We recommend using a protective barrier such as a cloth or a
piece of glass between the unit and the surface to reduce the risk of damage and/or staining.
• WARNING: Use of this unit near uorescent lighting may cause interference
regarding use of the remote. If the unit is displaying erratic behavior move
away from any uorescent lighting, as it may be the cause.
• WARNING: Shock hazard - Do Not Open.
• AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR
Mains plug is used as disconnect device and it should remain readily operable during
intended use. In order to disconnect the apparatus from the mains completely, the
mains plug should be disconnected form the mains socket outlet completely.
La prise du secteur est utilisé pour déconnecter le système.
La prise du secteur ne doit pas être obstruée ou doit être facilement
accessible pendant son utilisation. Pour être complètement déconnecté de
l’alimentation d’entrée, la prise doit être débranchée du secteur.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.
No mezcle baterías viejas y nuevas.
No mezcle baterías alcalinas, estándar (carbono-zinc) o recargables (ni-cad, ni-mh, etc.).
WARNING: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION
RISQUE D' ÉLECTROCUTION
NE PAS OUVRIR
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
This symbol indicates that this product
incorporates double insulation between hazardous
mains voltage and user accessible parts.
The lightning ash with arrowhead symbol,
within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufcient magnitude to constitute a risk of
electric shock to persons.
IMPORTANT SAFETY INSTRUCTIONS
Introduction and Setup
FCC Warnings
Power
The battery backup is intended for
short power outages only. The clock
radio’s primary functions cannot run
off of the battery backup alone.
Requires 2, AAA-size, batteries (not included)
Insert the stand into the corresponding holes.
OPEN
Battery Backup
Stand
Additional Warnings
WARNINGS AND PRECAUTIONS
M
S
POWER SOURCE
CLK / ALA 1 / 2
– TUNE +
DIMMER / MEM+
VOLUME
SNOOZE
PAIR
USB
CHARGER LINE IN
DC IN 5V
FM ANT
Volume
Press to adjust
the volume.
Source
Press to switch
between Bluetooth,
FM Radio, and
Line In modes.
M/Clk/Ala 1/2/Pair
In FM Radio mode,
press to begin saving
the current radio
station as a preset.
Press and hold to
autosave preset
channels.
In Off mode, press
and hold to begin
setting the clock.
Press to begin
setting the alarm.
Press to begin pairing
a Bluetooth device
in Bluetooth mode.
Tune +/-
Press to tune
the radio in FM
Radio Mode.
Press and hold to
search for the next
available frequency.
Power
Press to turn the
unit on or off.
Dimmer/Play/
Pause/Mem +
Press and hold to
adjust the brightness
of the display.
Press to play or
pause a track in
Bluetooth mode.
In FM Radio Mode,
press to cycle
through preset
radio stations. Snooze/Sleep
Press to set the sleep timer.
Press to delay the alarm.
Line In
FM Antenna Wire
USB Charger
For Warranty Information and the most up-to-date version of this User’s Guide, go to www.iLiveElectronics.com Customer Service: 1-888-999-4215
Email Support: [email protected], Email Parts: [email protected]
Copyright © 2013 Digital Products International (DPI, Inc.) All other trademarks appearing herein are the property of their respective owners. Specications are subject to change without notice.
The Bluetooth word mark and logos are owned by the Bluetooth SIG.
ICB103-842-01-IB.indd 1 6/17/2013 12:27:12 PM
ICB103BU Bluetooth Speaker with Clock

1. Press the Power button
to turn the unit off.
2. Press and hold the M/Clk/Ala 1/2/
Pair button until the display begins
to blink, then release the button.
3. Press the Tun+/- button to adjust the hour.
4. Press the M/Clk/Ala 1/2/Pair button.
5. Press the Tun+/- button to
adjust the minute.
6. Press the M/Clk/Ala 1/2/Pair
button to nish setting the time.
1. Press the Power button
to turn the unit off.
2. Press the M/Clk/Ala 1/2/Pair button
to select Alarm 1 or Alarm 2.
3. To begin setting the selected alarm,
press and hold the M/Clk/Ala 1/2/
Pair button until the display begins
to blink, then release the button.
4. Press the Tun+/- button to adjust the hour.
5. Press the M/Clk/Ala/Pair 1/2 button.
6. Press the Tun+/- button to
adjust the minute.
7. Press the M/Clk/Ala 1/2/Pair button.
8. Press the Tun+/- button to switch
between FM Radio, Buzzer, or Off.
9. Press the M/Clk/Ala 1/2/Pair button.
10. Once the set alarm time is reached,
the alarms will sound.
To set the other alarm, follow
the above steps and choose
the alarm not currently set.
Clock and Sleep Timer
Alarm
Setting the Clock
1. Press the Power button
to turn the unit on.
2. Press the Snooze/Sleep button
repeatedly to set the sleep timer
( 90, 80, 70, 60, 50, 40, 30,
20, 10, 5, 3 min or OFF ).
3. Once the set sleep time has expired
the unit will automatically power off.
Setting the Sleep Timer
Setting the Alarm
After the alarm sounds:
Press the Snooze/Sleep button to
delay the alarm for several minutes.
OR
Press the Power button to turn the alarm off
until the set alarm time is reached again.
Snooze and Alarm Reset
To download this User’s Guide in English,
Spanish, or French, or to get answers to
frequently asked questions, visit the support
section at: www.iLiveElectronics.com
Para descargar este Manual del
Usuario en inglés, español y francés, o
para obtener respuestas a preguntas
frecuentes, visite la sección de apoyo
en www.iLiveElectronics.com
Pour télécharger ce guide de l’utilisateur
en anglais, espagnol ou français, ou pour
obtenir des réponses à des questions
fréquemment posées, consultez la rubrique
d’assistance sur www.iLiveElectronics.com
International Support
Requires a 3.5mm audio cable (not included)
1. Connect a 3.5mm audio cable to the
Line In on the unit and an audio output
on an MP3 player or other audio source.
2. Press the Source button to
switch to Line In mode.
The display will show “AU”.
3. Use the native controls on the
connected MP3 player or other audio
source to play and control audio
played through the clock radio.
1. Press the Power button
to turn the unit on.
2. Press the Source button to
switch to FM Radio mode.
3. Press the Tun+ and Tun-buttons to
adjust the radio to the desired frequency.
4. Press and hold the Tun+ and
Tun- buttons to search for the
next available frequency.
5. Press the Vol+/- buttons
to adjust the volume.
6. Press the Power to turn the radio off.
Adjust the position of the FM wire
antenna to improve FM radio reception.
1. Follow the instructions for
Tuning the FM Radio.
2. Tune to the desired station.
3. Press the M/Clk/Ala 1/2/Pair button.
4. Press the Dimmer/Play/Pause/Mem+
button to choose the preset number.
5. Press the M/Clk/Ala 1/2/Pair button
to save the station as a preset.
Up to 20 stations may be
saved as presets.
1. Follow the instructions for Tuning the
Radio and Saving a Station as a Preset.
2. Press the Play/Pause button to cycle
through preset radio stations.
1. Follow the instructions for
Tuning the Radio.
2. Press and hold the M/Clk/
Ala 1/2/Pair button.
3. The unit will scan for an available station,
and save it as a preset. It will then scan
for the next available station, and set
that as the next preset, continuing until
up to 20 stations are saved as presets.
Line In
Charging
Using the Line In
Radio
Tuning the FM Radio
Saving a Station as a Preset
Charging a Device
Autosaving Preset Radio Stations
Tuning Preset Radio Stations
For Warranty Information and the most up-to-date version of this User’s Guide, go to www.iLiveElectronics.com Customer Service: 1-888-999-4215
Email Support: [email protected], Email Parts: [email protected]
Copyright © 2013 Digital Products International (DPI, Inc.) All other trademarks appearing herein are the property of their respective owners. Specications are subject to change without notice.
The Bluetooth word mark and logos are owned by the Bluetooth SIG.
Bluetooth Setup
Pairing a Bluetooth Device for the First Time
1. Power on the unit by pressing
the Power button.
2. Press the Source button to
switch to Bluetooth mode.
Bluetooth mode is indicated
by “bt” on the display.
The Bluetooth icon will ash slowly.
3. Press the Pair button.
The Bluetooth icon will ash quickly.
When pairing, remain within
3 feet of the unit.
4. Using the native controls on your
Bluetooth device, select the “ICB103”
in your Bluetooth settings to pair.
If your device requests a password,
enter the default password “ 0 0 0 0 ”.
Refer to the user’s manual for your
specic device for instructions on pairing
and connecting Bluetooth devices.
5. When successfully paired and connected,
the Bluetooth icon will remain solid.
After initial pairing, the unit will stay paired
unless unpaired manually by the user or
erased due to a reset of the device.
If your device should become
unpaired or you nd it is unable to
connect, repeat the above steps.
1. Follow the instructions for
Pairing a Bluetooth Device.
2. Use the native controls on the connected
Bluetooth Device to select a track.
3. To play or pause the selected
track, use the native controls on
the connected Bluetooth Device or
press the Play/Pause button.
4. Audio played through the connected
Bluetooth device will now be
heard through the speakers.
Playing Audio Wirelessly
1. Make sure the unit is
plugged into the wall.
2. Using the appropriate USB charging
cable (not included), connect one
end to the device and the other to
the USB Charger on the unit.
Refer to the user’s manual for your
specic device for manufacturers
required charging amperage as well
as determining the appropriate cable
for your device before charging.
Note: This device uses a USB
charging port with a 500mA
maximum charging capacity, making
it unsuitable for charging iPads.
3. The device will now charge.
ICB103-842-01-IB.indd 2 6/17/2013 12:27:14 PM

FCC NOTE：
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS OR CHANGE
TO THIS EQUIPMENT. SUCH MODIFICATIONS OR CHANGE COULD VOID AND
CHANGE ANNTENA WHICH THE MANUFACTURER PROVIDES.
IT IS THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a resi dential installation.
This equipment generates, uses and can radiate radio frequenc y energy and, if not
installed and used in accordance with the in structions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular insta llation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to corr ect the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experien ced radio/TV technician for help.
To maintain compliance with FCC’s RF exposure guidelines, this equipment should be
installed and operated with a minimum distance of 20cm between the radiator and your
body.