iLive ITDP310B User manual

USER’S GUIDE
V:1016-0701-10
For the most up-to-date version of this User’s Guide, go to www.ilive.net
ITDP310B
DVD Bar Speaker for iPhone and iPod

iLive2
• WARNING:Lithium batteries, like all rechargeable
batteries are recyclable and should be recycled or
disposed of in normal household waste. Contact your
local government for disposal or recycling practices in
your area. They should never be incinerated since they
might explode.
• WARNING: Shock hazard - Do Not Open.
• AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS
OUVRIR
Mains plug is used as disconnect device and it should
remain readily operable during intended use. In order
to disconnect the apparatus from the mains completely,
the mains plug should be disconnected from the mains
socket outlet completely.
La prise du secteur est utilisé pour déconnecter le
système.
La prise du secteur ne doit pas être obstruée ou doit être
facilement accessible pendant son utilisation. Pour être
complètement déconnecté de l’alimentation d’entrée, la
prise doit être débranchée du secteur.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or
rechargeable (ni-cad, ni-mh, etc) batteries.
No mezcle baterías viejas y nuevas.
No mezcle baterías alcalinas, estándar (carbono-zinc) o
recargables (ni-cad, ni-mh, etc.).
• CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
• WARNING:To reduce the risk of re or electric shock,
do not expose this apparatus to rain or moisture.
• AveRTIssemeNT: Pour réduire le risque d’incendie
ou de choc électrique, ne pas exposer cet appareil sous la
pluie et l’humidité.
• CAUTION: Use of any controls or adjustments or
performance of procedures other than those herein
specied may result in hazardous radiation exposure.
• WARNING: Changes or modications to this unit
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
• WARNING: Do not place the unit on top of any soft,
porous, or sensitive surfaces to avoid damaging the
surface. Use a protective barrier between the unit and
surface to protect the surface.
• WARNING: Use of this unit near uorescent lighting
may cause interference regarding use of the remote. If
the unit is displaying erratic behavior move away from
any uorescent lighting, as it may be the cause.
• CAUTION:Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent type.
• PRÉCAUTION: Danger d’explosion si les piles sont
remplacées de façon incorrect. Remplacer les piles
seulement par le même type de pile ou l’équivalent.
• WARNING: There is a danger of explosion if you
attempt to charge standard Alkaline batteries in the unit.
Only use rechargeable NiMH batteries.
• WARNING: The remote control’s button cell battery
contains mercury. Do not put in the trash, instead recycle
or dispose of as hazardous waste
The lightning ash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufcient magnitude to constitute a risk of electric
shock to persons.
WARNING: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
ATTENTION
RISQUE D' ÉLECTROCUTION
NE PAS OUVRIR
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
This product utilizes a Class 1 laser to read
Compact Discs. This laser Compact Disc Player is
equipped with safety switches to avoid exposure
when the CD door is open and the safety interlocks
are defeated. Invisible laser radiation is present
when the CD Player’s lid is open and the system’s
interlock has failed or been defeated. It is very
important that you avoid direct exposure to the
laser beam at all times. Please do not attempt to
defeat or bypass the safety switches.
Warnings and Precautions

Customer Support: 1-888-999-4215 iLive 3
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualied service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
• The apparatus shall not be exposed to dripping or splashing and
that no objects lled with liquids, such as vases, shall be placed
on apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux
éclaboussures et aucun objet ne contenant de liquide, tel qu’un
vase, ne doit être placé sur l’objet.
• Main plug is used as disconnect device and it should remain
readily operable during intended use. In order to disconnect the
apparatus from the mains completely, the mains plug should be
disconnected form the mains socket outlet completely.
La prise du secteur ne doit pas être obstruée ou doit être
facilement accessible pendant son utilisation. Pour être
complètement déconnecté de l’alimentation d’entrée, la prise doit
être débranchée du secteur.
• Battery shall not be exposed to excessive heat such as sunshine,
re or the like.
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à
la lumière du soleil, au feu ou autres choses de semblable.
• Caution marking is located at the rear or back of the apparatus.
Attention marquage est situé à l’arrière ou à l’arrière de
l’appareil
• The marking information is located at the rear or back of
apparatus.
Les informations de marquage est situé à l’arrière ou à l’arrière
de l’appareil.
This product incorporates copyright protection technology that is protected
by U.S. patents and other intellectual property rights. Use of this copyright
protection technology must be authorized by Rovi Corporation, and is intended
for home and other limited viewing uses only unless otherwise authorized by
Rovi Corporation. Reverse engineering and disassembly are prohibited.
FCC Warnings
Additional Warnings
1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding - type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
When the provided plug does not t into your outlet,
consult an electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the
manufacturer.
12.
This symbol indicates that this product
incorporates double insulation between
hazardous mains voltage and user
accessible parts.
Use only with a cart, stand, tripod,
bracket, or table specied by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
Important Safety Instructions

iLive4
• Made for iPhone
• Made for iPod
• Plays and charges docked iPhone and iPod
• DVD player: DVD, DVD±R/RW
• CD player: CD, CD-R/RW
• 2 channel speaker system
• Tube technology for enhanced bass
• Preset EQ
• Bass & treble control
• High Denition Conversion DVD up to 1080p
• Multi-Language OSD: On-Screen Display in
English, French and Spanish
• NTSC
• Motorized DVD/iPod door
• Digital tune FM radio
• 10 station memory presets
• Last user setting for volume and function
• Digital clock
• Alarm
• Gradual wake to radio or iPhone/iPod
• Sleep
• Negative LCD display with 0.5” character size
and white backlight
• AV1 and AV2 input
• 3.5mm audio input
• RCA audio input
• HDMI output
• Composite video output
• Subwoofer output
• Remote control: requires 2, AAA size,
batteries (included)
• AC power: Built in AC power cable
• Remote control: requires 2, AAA size,
batteries (included)
• Wall-mount bracket
• (4) Screws for mounting
• Brackets for docking iPhone/iPod (5)
• FM wire antenna
• Audio/video cable
• Warranty card
• User’s guide
Features Included
DVD Bar Speaker for iPhone and iPod

Customer Support: 1-888-999-4215 iLive 5
TABLE OF CONTENTS
Warnings and Precautions . . . . . . . . . . . . . . . . . . 2
Important Safety Instructions . . . . . . . . . . . . . . . . . 3
• FCC Warnings
• Additional Warnings
DVD Bar Speaker for iPhone and iPod . . . . . . . . . . . . . . . 4
• Features
• Included
Introduction . . . . . . . . . . . . . . . . . . . . . 6
Setup . . . . . . . . . . . . . . . . . . . . . . . 8
• Power
• Remote
Clock and Alarm . . . . . . . . . . . . . . . . . . . . 9
• Setting the Clock
• Setting the Alarm
iPod/iPhone . . . . . . . . . . . . . . . . . . . . . 10
• Docking an iPod or iPhone
• Playing an iPod and iPhone
Radio . . . . . . . . . . . . . . . . . . . . . . . 11
• Playing the FM Radio
• Saving an FM station as a Preset
• Listening to Preset Radio Stations
• Loading a DVD or CD
• Playing a DVD or CD
• Programming a DVD or CD
DVD and CD . . . . . . . . . . . . . . . . . . . . . 13
• DVD Setup Menu
Basic Connectivity . . . . . . . . . . . . . . . . . . . . 14
Audio/Video 1 and 2 . . . . . . . . . . . . . . . . . . . 15
• AV1 and AV2
Connecting a Television . . . . . . . . . . . . . . . . . . 16
• Composite Video Output
• Using the RCA Audio Input
• HDMI Output
Audio . . . . . . . . . . . . . . . . . . . . . . . 17
• Using the 3.5mm Audio Input
• Using the RCA Audio Input
• Using the Subwoofer Output
Mounting the Bar Speaker to a Wall . . . . . . . . . . . . . . . . 18
• Important Notes
• Required Tools
• Included Hardware
Mounting the Bar Speaker to a Wall . . . . . . . . . . . . . . . . 19
• Mounting - Getting Started
Company Information . . . . . . . . . . . . . . . . . . . 20
• Green Initiative
• International Support
• Contact Information

iLive6
Introduction
PLAY/PAUSE
Press to play or pause
a loaded or docked CD,
DVD, iPhone, or iPod.
MEM/STOP
Press to stop a loaded
or docked CD, DVD,
iPhone, or iPod during
play. In radio mode,
press to save the
current station as a
preset.
SKIP
Press to skip between
tracks or chapters on a
loaded or docked CD,
DVD, iPhone, or iPod.
CLOCK
With the power o,
press to set the clock.
DVD OPEN/CLOSE
Press to open or close
the DVD compartment.
AV1 and AV2
Use to input RCA audio
and Composite video
into the bar speaker.
RESET
Press using a paperclip
or like object to reset
the bar speaker to it’s
original settings.
FM WIRE ANTENNA
Adjust to improve the
FM radio reception.
SUBWOOFER OUTPUT
VIDEO OUTPUT
3.5mm AUDIO INPUT
POWER
Press to turn the bar
speaker’s power o
or on.
SOURCE
Press to switch
between iPod, FM
radio, DVD, AUX, LINE,
AV1, and AV2 modes.
VOLUME
Press to adjust the
volume output from
the bar speaker.
iPod
Press to switch to iPod
mode.
iPod OPEN/CLOSE
Press to open or close
the iPhone/iPod
compartment.
RCA AUDIO INPUT
HDMI OUTPUT
AC POWER CABLE

Customer Support: 1-888-999-4215 iLive 7
POWER
Press to turn the bar speaker’s power o
or on.
NUMBER KEYPAD
STOP
Press to stop a loaded or docked CD, DVD,
iPhone, or iPod during play.
FAST-FORWARD/FAST-REWIND/TUNE +/-
In DVD mode, press to fast-forward or fast-
rewind a loaded DVD or CD. In FM radio
mode, press to tune the FM radio.
PLAY
Press to play a loaded or docked CD, DVD,
iPhone, or iPod.
PAUSE/STEP
Press to pause a loaded or docked CD,
DVD, iPhone, or iPod. In DVD mode, press
continuously to step through a playing
DVD one frame at a time.
DIRECTIONAL/SELECT
Press to navigate DVD, iPhone, and iPod
menus. Press to make selections on a
loaded DVD, CD, iPhone, or iPod.
iPod
Press to switch to iPod mode.
CLOCK
With the power o, press to set the clock.
SLEEP
Press repeatedly to set the sleep timer.
SETUP
Press to access the DVD setup menu.
PROGRAM/MEM
Press to program a loaded CD or DVD to
play tracks or chapters in a specied order.
In radio mode, press to save the current
station as a preset.
EQ and N/P
Press to adjust the EQ setting. In DVD
mode, with the DVD stopped, press and
hold to switch between NTSC ,PAL, and
AUTO.
WIDE
In DVD mode, press to switch between
Normal/PS, Normal/LB, and Wide screen
format.
REP/ST
Press to repeat a chapter or track, title, or
entire album. In radio mode, press to turn
FM stereo o and on.
A-B REPEAT
Press to create a repeating loop on a
specied section of a loaded DVD.
AUDIO
Press to adjust the audio options on the
loaded DVD.
ANGLE
On supported DVDs, press to view
alternate angles.
iPod OPEN/CLOSE
Press to open or close the iPhone/iPod
compartment.
DVD OPEN/CLOSE
Press to open or close the DVD
compartment.
GOTO
Press to go to a specied chapter, title, or
time on a loaded DVD.
NEXT/PREVIOUS/MEMORY +/-
Press to skip between chapters or tracks. In
radio mode, press to cycle through saved
radio stations.
SOURCE
Press to switch between iPod, FM radio,
DVD, AUX, LINE, AV1, and AV2 modes.
ALARM
Press to set the alarm.
MENU
In DVD or iPod mode, press to return to the
loaded DVD’s main menu or docked iPod’s
previous menu.
BASS/TREBLE
Press to adjust the bass and treble levels
when in EQ at mode.
VOLUME
Press to adjust the volume.
ALBUM/CHAPTER/PLAYLIST
Press to cycle through albums, chapters, or
playlists on a docked iPhone or iPod.
HDMI
In DVD mode, press repeatedly to adjust
the resolution output from the bar speaker.
SHUFFLE
Press to play tracks from a DVD, CD, iPhone,
or iPod in a random order.
DISPLAY
In DVD mode, press to view the on-screen
display. In radio mode, press to view the
time.
SUBTITLE
Press to adjust the subtitle options on the
loaded DVD.
ZOOM
Press to adjust the zoom on a playing DVD.
MUTE
Press to mute the volume.
SLOW
Press to watch the loaded DVD in slow
motion.
TITLE
Press to return to the loaded DVDs title
menu.

iLive8
Plug the attached AC power cable into a
standard AC power outlet to power the bar
speaker.
Requires 2, AAA size, batteries (included)
Setup
Power
Remote

Customer Support: 1-888-999-4215 iLive 9
1. Press the POWER button to turn the bar
speaker o.
2. Press the CLOCK button.
The hour will begin to blink.
3. Press the SKIP buttons on the bar speaker or
the up and down DIRECTIONAL buttons on
the remote to adjust the hour.
4. Press the CLOCK button.
The minute will begin to blink.
5. Press the SKIP buttons on the bar speaker or
the up and down DIRECTIONAL buttons on
the remote to adjust the minute.
6. Press the CLOCK button to nish setting the
time.
1. Press the ALARM button.
The hour will begin to blink.
2. Press the SKIP buttons on the bar speaker or
the up and down DIRECTIONAL buttons on
the remote to adjust the hour.
3. Press the ALARM button.
The minute will begin to blink.
4. Press the SKIP buttons on the bar speaker or
the up and down DIRECTIONAL buttons on
the remote to adjust the minute.
5. Press the ALARM button repeatedly to cycle
between OFF, FM RADIO, and iPod.
When the display shows iPod, press the
SELECT button on the remote to wake to the
docked iPhone or iPod.
When the display shows the FM radio, press
the MEMORY +/- buttons on the remote
to select an FM radio preset, then press the
SELECT button on the remote to wake to the
selected FM radio station.
Setting the Clock
Setting the Alarm
Clock and Alarm

iLive10
1. Locate the numbered bracket that ts the
iPhone/iPod model that will be docked.
Each included bracket has a number on it,
indicating which iPhone/iPod model that
bracket is compatible with. See the separate
bracket chart page to identify which bracket is
needed.
2. Press the iPod button to switch to iPod
mode.
3. Press the iPod OPEN/CLOSE button to open
the iPhone/iPod compartment.
4. Insert the bracket into the dock for iPhone
and iPod.
5. Dock the iPod or iPhone into the dock.
6. Press the iPod OPEN/CLOSE button to close
the iPhone/iPod compartment.
iPod/iPhone
Docking an iPod or iPhone
1. Follow the instructions for Docking an iPod
or iPhone.
2. Press the PLAY button to begin playing
music from the docked iPhone or iPod.
Playing an iPod and iPhone

Customer Support: 1-888-999-4215 iLive 11
1. Press the SOURCE button repeatedly to
switch to FM radio mode.
2. Press the TUNE +/- buttons on the remote or
the SKIP buttons on the bar speaker to tune
the FM radio.
1. Follow the instructions for Playing the FM
Radio.
2. Tune the radio to the desired station.
3. Press the MEM/STOP button.
4. Press the M +/- buttons on the remote or the
SKIP buttons on the bar speaker to select a
preset number.
5. Press the MEM/STOP button to save the
current station to the selected preset.
1. Follow the instructions for Playing the FM
Radio.
2. Follow the instructions for Saving an FM
station as a Preset.
3. Press the M +/- buttons on the remote
control to cycle through saved FM radio
presets.
Playing the FM Radio
Saving an FM station as a Preset
Listening to Preset Radio Stations
Radio

iLive12
1. Press the SOURCE button to switch to DVD
mode.
2. Press the DVD OPEN/CLOSE button to open
the DVD compartment.
3. Insert a DVD or CD into the DVD
compartment, label side facing out.
1. Follow the instructions for Loading a DVD or
CD and Playing a DVD or CD.
2. Press the PROG/MEM button on the remote.
3. Use the NUMBER KEYPAD to enter in the
titles and chapters or tracks in the order you
want them to play.
4. Use the DIRECTIONAL buttons to select the
on-screen START button. Press the SELECT
button to begin playing the programmed
DVD or CD.
5. To cancel the program play, press the STOP
button twice.
1. Follow the instructions for Loading a DVD or
CD.
2. Press the PLAY button to begin playing the
loaded disc.
To watch a DVD, the bar speaker must be
connected to a television.
DVD and CD
Loading a DVD or CD
Programming a DVD or CD
Playing a DVD or CD

Customer Support: 1-888-999-4215 iLive 13
GENERAL
TV Display
• Use to switch between Normal/PS, Normal/
LB, and Wide.
Angle Mark
• Use to turn the Angle Mark on or o. When
on, an angle mark icon will appear on
supported DVDs when alternate angles can
be viewed.
OSD Language
• Use to adjust the on-screen display
language.
Screen Saver
• Use to turn the screen saver o or on.
AUDIO
Downmix
• Use to switch between LT/RT and Stereo.
VIDEO
HDMI Resolution
• Use to switch between 480i, 480p, 720p,
1080i, and 1080p.
Quality
• Use to adjust the brightness, contrast, hue
and saturation of video output through the
bar speaker.
SYSTEM
TV Type
• Use to switch between NTSC, PAL, and
AUTO. This can also be adjusted by using
the N/P button on the remote control.
Audio
• Use to adjust the audio language for the
loaded DVD.
Subtitle
• Use to adjust the subtitle language for the
loaded DVD.
Disc Menu
• Use to adjust the disc menu language for
the loaded DVD.
Default
• Use to reset the DVD player settings back
to their original conguration.
DVD and CD
DVD Setup Menu

iLive14
Basic Connectivity
DVD PLAYER
DIGITAL CABLE or SATELLITE TUNER
VCR
GAMING CONSOLE
SUBWOOFER
AUDIO
AND/OR
VIDEO
AUDIO
AND/OR
VIDEO
VIDEOHDMI
AUDIO AUDIO
AUDIO
MP3 PLAYER
Below, you’ll see a basic ow chart of how you can connect your home entertainment devices to the
bar speaker, and in turn how the bar speaker connects to them.

Customer Support: 1-888-999-4215 iLive 15
Requires an RCA audio/video cable (not
included)
Potential Connections: Gaming System, Set-top
Box, VCR, External DVD Player
1. Connect an RCA audio/video cable AV1 or
AV2 inputs on the back of the bar speaker
and to a gaming system, set-top box, VCR, or
external DVD player..
2. Press the SOURCE button to switch to AV1 or
AV2 mode.
3. Use the connected audio and video source’s
native controls to play and control audio and
video played through the connected bar
speaker.
4. Use the COMPOSITE VIDEO OUTPUT or
HDMI OUTPUT to output video incoming to
the bar speaker to a television.
Audio/Video 1 and 2
AV1 and AV2

iLive16
Connecting a Television
Requires an RCA video cable (not included)
1. Connect an RCA video cable to the
COMPOSITE VIDEO OUTPUT on the bar
speaker and a composite video input on a
television.
2. Adjust the connected television to the
correct input setting.
3. Video played on or through the bar speaker
will now show on the connected television.
Requires an HDMI cable (not included)
Please note, the HDMI output will not support video
from a docked iPod or iPhone. To output video from
an iPod or iPhone, use the Composite Video Output.
1. Connect an HDMI cable to the HDMI
OUTPUT on the bar speaker and a HDMI
input on a television.
2. Adjust the connected television to the
correct input setting.
3. Audio and video played on or through the
bar speaker will now show on the connected
television.
Composite Video Output
Good - Video
HDMI Output
Best - Audio and Video
Requires an RCA audio cable (not included)
1. Connect an RCA audio cable to the RCA
AUDIO INPUT on the back of the bar speaker
and an audio output on an audio source.
2. Press the SOURCE button to switch to AUX
mode.
3. Use the connected audio source’s native
controls to play and control audio played
through the connected bar speaker.
Using the RCA Audio Input
Good - Audio

Customer Support: 1-888-999-4215 iLive 17
Audio
Requires a 3.5mm audio cable (not included)
1. Connect a 3.5mm audio cable to the 3.5MM
AUDIO INPUT on the side of the bar speaker
and an audio output on an audio source.
2. Press the SOURCE button to switch to LINE
mode.
3. Use the connected audio source’s native
controls to play and control music played
through the connected bar speaker.
Requires an RCA audio cable (not included)
1. Connect an RCA audio cable to the RCA
AUDIO INPUT on the back of the bar speaker
and an audio output on an audio source.
2. Press the SOURCE button to switch to AUX
mode.
3. Use the connected audio source’s native
controls to play and control music played
through the connected bar speaker.
Requires an RCA audio cable (not included)
1. Connect an RCA audio cable to the
SUBWOOFER OUTPUT on the back of the
bar speaker and an external subwoofer.
2. The bar speaker will automatically use the
connected subwoofer when playing audio.
Using the 3.5mm Audio Input
Using the RCA Audio Input
Using the Subwoofer Output

iLive18
Mounting the Bar Speaker to a Wall
We recommend having this bar speaker
professionally mounted.
• Manual or Power Screwdriver
• Stud Finder
• Pencil
• Tape Measure
• Level
• One Wall Mount Bracket
• (4) Screws
Important Notes
Required Tools
Included Hardware

Customer Support: 1-888-999-4215 iLive 19
STUDS
WALL
MOUNTING BRACKET
16”
FROM CENTER TO CENTER
Mounting the Bar Speaker to a Wall
1. Use the TAPE MEASURE to decide how high
you’d like to hang the bar speaker on the
wall.
The bar speaker must be hung within 6 feet of
an AC power outlet for the attached AC power
cable to reach.
2. Use the STUD FINDER to locate 2 parallel
wooden studs to screw the mounting
brackets into.
3. Mark the wall at the center of the studs using
the PENCIL.
4. Line the LEVEL up on both of your marks to
make sure they are level. If they’re not, adjust
the marks as needed to make them level.
5. After you’ve double checked your markings,
DRILL through the top holes on the
mounting bracket directly into the pencil
marks you’ve made on the wall.
6. Use the LEVEL to level the mounting bracket,
then drill the remaining screws into the
bottom holes on the mounting bracket.
7. Slide the bar speaker onto the mounting
bracket, and make certain there is a rm and
stable connection before letting go of the bar
speaker.
8. Finally, use the LEVEL to conrm that the bar
speaker is level.
Mounting - Getting Started

Copyright © 2010 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners.
Specications are subject to change without notice
Company Information
Environmental Commitment to ‘Protect for Today
and Sustain for Tomorrow’
2009 marked the ocial launch of DPI, Inc.’s
corporate campaign for a greener and cleaner
world. DPI is building upon environmental
initiatives introduced at all of their facilities
to help formulate and sustain signicant and
important conservation eorts within its
manufacturing and marketing communities.
In addition to targeting and selecting energy
ecient product features, and structuring ‘green
oce’ procedures, other initial program eorts
include:
• Reduction of all packaging sizes
• Recyclable plastics for clamshell packages, with a plan
to eventually replace plastic with recyclable paper
• Recycled ber board in place of the polyfoam in
packing boxes
• Recycled plastics in place of the virgin material in
product construction
To download this User’s Guide in English,
Spanish, or French, visit the support section at
www.ilive.net.
Para transferir esta guía de usuario en inglés,
español, o francés, visite la sección de la ayuda
en www.ilive.net.
Pour télécharger ce guide de l’utilisateur en
anglais, espagnol, ou français, visitez la section
de soutien chez www.ilive.net.
Phone:
1-888-999-4215
Email:
[email protected]
Parts Email:
partsinf[email protected]
Website:
www.ilive.net
Green Initiative International Support
Contact Information