iLive ITP152 User manual

USER’S GUIDE
V:1047-0103-12
For the most up-to-date version of this User’s Guide, go to www.ilive.net
ITP152
Tower Soundbar

2
• WARNING:The battery, batteries, and battery pack
shall not be exposed to excessive heat such as sunshine,
re, or the like.
• WARNING: Shock hazard - Do Not Open.
• AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS
OUVRIR
Mains Plug or Direct plug-in adapter is used as disconnect
device and it should remain readily operable during intended
use. In order to disconnect the apparatus from the mains
completely, the Mains Plug or Direct plug-in adapter should
be disconnected from the mains socket outlet completely.
La che d’alimentation ou adaptateur de courant est utilisé
comme dispositif de déconnexion et doit rester accessible
pendant l’utilisation. Pour mettre l’appareil hors tension, la
che ou adaptateur de courant doit être débranché de la prise
de courant.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable
(ni-cad, ni-mh, etc) batteries.
No mezcle baterías viejas y nuevas.
No mezcle baterías alcalinas, estándar (carbono-zinc) o
recargables (ni-cad, ni-mh, etc.).
• CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
• WARNING:To reduce the risk of re or electric shock,
do not expose this apparatus to rain or moisture.
• AVERTISSEMENT: Pour réduire le risque d’incendie
ou de choc électrique, ne pas exposer cet appareil sous la
pluie et l’humidité.
• CAUTION: Use of any controls or adjustments or
performance of procedures other than those herein
specied may result in hazardous radiation exposure.
• WARNING: Changes or modications to this unit
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
• WARNING: Do not place the unit on top of any soft,
porous, or sensitive surfaces to avoid damaging the
surface. Use a protective barrier between the unit and
surface to protect the surface.
• WARNING: Use of this unit near uorescent lighting
may cause interference regarding use of the remote. If
the unit is displaying erratic behavior move away from
any uorescent lighting, as it may be the cause.
• CAUTION:Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent type.
• PRÉCAUTION: Danger d’explosion si les piles sont
remplacées de façon incorrect. Remplacer les piles
seulement par le même type de pile ou l’équivalent.
Warnings and Precautions
The lightning ash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufcient magnitude to
constitute a risk of electric shock to persons.
WARNING: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
ATTENTION
RISQUE D' ÉLECTROCUTION
NE PAS OUVRIR
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.

Customer Support: 1-888-999-4215 3
13. Unplug this apparatus during lightning storms
or when unused for long periods of time.
14. Refer all servicing to qualied service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
WARNING: Changes or modications to this unit not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• The apparatus shall not be exposed to dripping or
splashing and that no objects lled with liquids,
such as vases, shall be placed on apparatus.
L’appareil ne doit pas être exposé aux écoulements
ou aux éclaboussures et aucun objet ne contenant de
liquide, tel qu’un vase, ne doit être placé sur l’objet.
• Battery shall not be exposed to excessive heat
such as sunshine, re or the like.
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à
la lumière du soleil, au feu ou autres choses de semblable.
• Caution marking is located at the rear or bottom of the apparatus.
Attention marquage est situé sur le paneau
arrière ou inférieur de l’unité.
• The marking information is located at the
rear or bottom of apparatus.
Le marquage est situé sur le paneau arrière ou inférieur de l’unité.
FCC Warnings
Additional Warnings
1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized
or grounding - type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. When the provided plug
does not t into your outlet, consult an electrician
for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories
specied by the manufacturer.
12.
Important Safety Instructions
This symbol indicates that this
product incorporates double insulation
between hazardous mains voltage
and user accessible parts.
Use only with a cart, stand, tripod,
bracket, or table specied by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
Special note: When placing your unit on a
lacquered or natural nish, protect your furniture
with a cloth or other protective material.

4
• Made for iPod and iPhone
• Plays and charges docked
iPod and iPhone
• 2.1 channel stereo sound
• FM Radio (PLL)
• Station memory presets (20 FM)
• Last station memory
• Direct access to FM stations
• Built-in FM wire antenna
• iPod and iPhone controls
• Universal Dock for iPod and iPhone:
supports universal dock adapters
• iPod and iPhone authentication IC
• Component video output
• Subwoofer output
• RCA stereo audio inputs
• 3.5mm audio input
• Bass controls
• Digital volume control
• Built-in stereo speakers
• Built-in subwoofer
• Full-function remote
• Cloth speaker grill
• Negative LCD display with
white backlight
• Digital clock
• AC power: built-in AC power cable
• Remote control: requires 2
AAA batteries (included)
• 5 dock adapters for iPod and iPhone
Tower Soundbar
Features Included

Customer Support: 1-888-999-4215 5
Table of Contents
Tower Soundbar ................................................................... 4
Features
Included
Table of Contents .................................................................. 5
Introduction ...................................................................... 6
Setup ............................................................................. 8
Power
Remote
Clock & Radio ..................................................................... 9
Setting the Clock
Auto Time Sync
Tuning the FM Radio
Saving a Radio Station as a Preset
Tuning to a Saved Preset Station
iPod/iPhone and Line in ..........................................................10
Docking an iPod or iPhone
Playing an iPod or iPhone
Using the 3.5mm Audio Input (Line)
Auto Time Sync
Audio Input, Subwoofer Output & Video Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using the Audio Input
Using the Subwoofer Output
Using the Component Video Output
Company Information ............................................................12
International Support
Contact Information
Green Initiative

6
Introduction
AUX IN SUB OUT
COMPONENT OUT
iPod Dock
Source
Press to switch between
iPod/iPhone, Line,
Tuner, and AUX modes.
Volume
Press to adjust
the volume.
Power
Press to power the
unit o or on.
Play/Pause
Press to play or pause a
docked iPhone or iPod.
With the unit powered
o, press and hold
to set the time.
Press and hold in
tuner mode to save
stations as a preset.
Tuning
Press to skip between
tracks on a docked
iPhone or iPod.
Press and hold to search
the current track on a
docked iPhone or iPod.
Audio Input
Sub Out
Component Out
Line In

Customer Support: 1-888-999-4215 7
CLOCK SYNC
TIME SET/MEM
Mute
Press to mute the volume.
Power
Press to power the
unit o or on.
Number Keypad
Clock Sync
Press and hold to sync
the clock with the
docked iPod or iPhone.
Playlist
Press to cycle through
playlists on a docked
iPhone or iPod.
Album
Press to cycle through
albums on a docked
iPhone or iPod.
Treble
Press to adjust the treble.
Sleep
Press repeatedly to
set the sleep timer.
iPod (+/-) / Tun (+/-)
Press to tune the FM radio.
Press to skip between
tracks on a docked
iPhone or iPod.
Press and hold to search
the current track on a
docked iPhone or iPod.
Chapter
Press to cycle through
chapters on a docked
iPhone or iPod.
Source
Press to switch between
iPod/iPhone, Line, Tuner,
and AUX modes.
Dimmer
Presss to adjust the
brightness of the display.
Repeat/ST
Press to repeat the
current track, or album.
Press to switch between
FM Mono and FM ST.
when in Tuner mode.
Menu
Press to cycle through
the menus on a docked
iPhone or iPod.
Bass
Press to adjust the bass.
Clockview/Shue
Press & hold to play songs
from a docked iPhone or
iPod in a random order.
Press to view the time
in playback mode.
Select
Press to make selections on
a docked iPhone or iPod.
iPod Menu (pq)
Press to navigate up and
down the menus on a
docked iPhone or iPod.
Volume
Press to adjust the volume.
Time Set/Mem/
Play/Pause
Press to play or pause a
docked iPhone or iPod.
With the unit powered
o, press and hold
to set the time.
Press in Tuner mode to
save stations as presets.

8
AC power: built in AC power cord.
Requires 2 AAA batteries (not included)
Power
Remote
AUX IN SUB OUT
COMPONENT OUT
SOURCE
REPEAT/ST MENU
TIME SET
MUTE
SLEEP
VOLUMECHAPTER
CLOCK VIEW
DIMMER
TREBLE BASS
i
P
o
d
-
/
T
U
N
-
i
P
o
d
M
E
N
U
i
P
o
d
+
/
T
U
N
+
OPEN
Setup

Customer Support: 1-888-999-4215 9
Clock & Radio
1. Press the Power button to turn
the tower speaker o.
2. Press and hold the Time Set button
on the remote or the Play/Pause
button on the unit for 3 seconds.
The hour on the DISPLAY
will begin blinking.
3. Press the Tuning buttons
to adjust the hour.
4. Press the Time Set button on the remote
or the Play/Pause button on the unit.
The minute on the DISPLAY
will begin blinking.
5. Press the Tuning buttons
to adjust the minute.
6. Press the Time Set button on the
remote or the Play/Pause button on
the unit to nish setting the time.
Setting the Clock
1. Press the Power button to turn
the tower speaker on.
2. Press the Source button to
switch to Tuner mode.
3. “Tuner” will appear on the display.
4. Press the Tuning buttons to
adjust the FM radio station.
Tuning the FM Radio
1. Follow the instructions for
Tuning the FM Radio.
2. Press and hold the Time Set/Mem
button on the remote or the Play/
Pause button on the unit.
3. Press the Tuning buttons to
select a preset (P01-P20).
4. Press the Time Set/Mem button
on the remote or the Play/Pause
button on the unit to save the current
station to the selected preset.
Saving a Radio Station as a Preset
1. In Tuner mode, press the Time Set/
Mem button on the remote or the Play/
Pause button on the unit repeatedly
to cycle through saved presets.
Tuning to a Saved Preset Station
1. Follow the instructions for
Docking an iPod or iPhone.
Auto time sync will not
work with all iPods.
2. The clock will automatically set to
the time of the docked iPhone.
Auto Time Sync

10
iPod/iPhone and Line in
1. Connect the iPod or iPhone
to the iPod Dock.
2. When the speaker is plugged in
and using AC power, the docked
iPod or iPhone will charge.
1. Follow the instructions for
Docking an iPod or iPhone.
2. Press the Source button on the
remote or the unit to switch
to iPode/iPhone mode.
3. Press the Play/Pause button on
the docked iPod or iPhone to begin
playing the docked iPod or iPhone.
Docking an iPod or iPhone
Playing an iPod or iPhone
Requires a 3.5mm audio
cable (not included)
1. Use a 3.5mm audio cable to connect
an MP3 player or other audio source to
the Line Input on the tower speaker.
2. Press the Power button to
power the tower speaker on.
3. Press the Source button to switch
the tower speaker to Line mode.
4. “Line” will appear on the display.
5. Audio played through the connected
MP3 player or other audio source will
now play through the tower speaker.
Using the 3.5mm Audio Input (Line)

Customer Support: 1-888-999-4215 11
Audio Input, Subwoofer Output & Video Output
1. Requires an RCA audio
cable (not included)
2. Use an RCA audio cable to connect an
MP3 player or other audio source to the
Audio Input on the tower speaker.
3. Press the Power button to
power the tower speaker on.
4. Press the Source button to switch
the tower speaker to AUX mode.
5. “AUX ” will appear on the display.
6. Audio played through the connected
MP3 player or other audio source will
now play through the tower speaker.
Using the Audio Input
Requires a component video
cable (not included).
1. Connect a component video cable
(not included) to the Component
Video Output and a television.
2. Adjust the connected television
to the correct input setting.
3. Press the Source button on the remote
to switch to iPod/iPhone Mode.
4. Video played through the docked
iPhone or iPod will now play on
the connected television.
Using the Component Video Output
Requires an RCA audio cable (not included)
1. Use an RCA cable (not included)
to connect an external subwoofer
to the Subwoofer Output.
2. When audio is played through any
source, the bar speaker will automatically
use the connected subwoofer.
Using the Subwoofer Output

Copyright © 2011 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are
the property of their respective owners. Specications are subject to change without notice
To download this User’s Guide in English,
Spanish, or French, or to get answers
to frequently asked questions, visit the
support section at www.ilive.net.
Para descargar este Manual del Usuario en
inglés, español y francés, o para obtener
respuestas a preguntas frecuentes, visite
la sección de apoyo en www.ilive.net.
Pour télécharger ce guide de l’utilisateur
en anglais, espagnol ou français, ou pour
obtenir des réponses à des questions
fréquemment posées, consultez la
rubrique d’assistance sur www.ilive.net.
Phone: [phone]
Email: [email protected]
Parts Email: par[email protected]
Website: www.ilive.net
Green InitiativeInternational Support
Contact Information
Company Information
Environmental Commitment to ‘Protect
for Today and Sustain for Tomorrow’
On a continual basis DPI, Inc. is making
eorts to sustain the environment
and improve the recyclability of
its products and packaging.
Focusing on “protecting for today and
sustaining for tomorrow” DPI, Inc. has
committed to reducing packaging size,
increasing the usage of recyclable plastics,
and ensuring that packaging and manuals
are made with up to 85% recycled material.
In addition to material consideration, DPI,
Inc. has also focused on the ner details that
positively impact the environment such as
employing the usage of soy-based inks.
DPI, Inc. also ensures that the factories
that produce the company’s wide
variety of consumer electronics adhere
to environmentally friendly air and
water restrictions. This is yet another
example that every step of the way
DPI, Inc. is making eorts to lessen
any impact on the environment.
In 2011 DPI, Inc. also began conversations
with Energy Star in order to ensure
that the consumer electronics being
produced meet high standards of energy
eciency. The ultimate goal is keeping
energy costs for consumers low while
providing quality, feature-rich products.