Iluminarc LOGIC Series User manual

LΩGIC™ 16X36
User Manual

Edition Notes
LΩGIC™ 16X36 User Manual Rev. 06
Edition Notes
The LΩGIC™ 16X36 User Manual Rev. 06 covers the description, safety precautions,
installation, programming, operation, and maintenance of the LΩGIC™ 16X36. ILUMINARC®
released this edition of the LΩGIC™ 16X36 User Manual Rev. 06 in May 2013.
Trademarks
The ILUMINARC® logo, the ILUMINARC®name, and all other trademarks in this document
related to services or products by ILUMINARC®are trademarks owned or licensed by
ILUMINARC®, its affiliates, or subsidiaries. Any other product names, logos, brands, company
names, or trademarks featured or referred to within this document are the property of their
respective trademark holders.
Copyright Notice
The entire content of this document, except where applicable and unless otherwise noted, is solely
owned by ILUMINARC®, a wholly owned trademark of CHAUVET & Sons Inc.
© Copyright 2013 ILUMINARC®
All rights reserved.
Electronically published by ILUMINARC®in the United States of America.
Manual Usage
ILUMINARC®authorizes its customers to download and print this manual for professional
information purposes only. ILUMINARC®expressly prohibits the usage, copy, storage,
distribution, modification, or printing of this manual or its content for any other purpose without
its written consent.
Document Printing
For better results, print this document in color, on letter size paper (8.5 x 11 inches), double sided.
If using A4 paper (210 x 297 mm), configure your printer to scale the content of this document to
A4 paper.
Intended Audience
Any person in charge of installing, operating, and/or maintaining the LΩGIC™ 16X36 should
read the Guide that shipped with it and this manual in their entirety before installing, operating, or
maintaining this product.
Disclaimer
ILUMINARC®believes that the information contained in this manual is accurate in all respects.
However, ILUMINARC®assumes no responsibility for any error or omissions in this document.
ILUMINARC®reserves the right to revise this document and to make changes from time to time
in the content hereof without obligation of ILUMINARC®to notify any person or company of
such revision or changes. This does not constitute in any way a commitment by ILUMINARC®to
make such changes. ILUMINARC®may issue a revision of this manual or a new edition of it to
incorporate such changes.
Document Revision
The LΩGIC™ 16X36 User Manual Rev. 06 supersedes all previous versions of this manual.
Please discard any older versions of this manual you may have, whether in printed or electronic
format, and replace them with this version.

Table of Contents
LΩGIC™ 16X36 User Manual (Rev. 06) i
Table of Contents
1. Introduction ...................................................................................................1
What is Included........................................................................................................... 1
Unpacking Instructions................................................................................................. 1
Text Conventions ......................................................................................................... 1
Safety Notes................................................................................................................. 2
Personal Safety...................................................................................................................2
Mounting and Installation.....................................................................................................2
Power and Wiring................................................................................................................2
Operation.............................................................................................................................2
2. Product Description......................................................................................3
Features ....................................................................................................................... 3
Additional Features..............................................................................................................3
Product Overview......................................................................................................... 4
3. Installation.....................................................................................................5
AC Power ..................................................................................................................... 5
Power Consumption............................................................................................................5
AC Plug ...............................................................................................................................5
Fuse Replacement ..............................................................................................................5
DMX Linking................................................................................................................. 6
Master/Slave Linking.................................................................................................... 6
LΩGIC™ 16X36 Product Linking ................................................................................. 7
Maximum Output Line Loading .................................................................................... 8
Cable Connections....................................................................................................... 9
Mounting..................................................................................................................... 10
Orientation.........................................................................................................................10
Installation.........................................................................................................................10
Procedure..........................................................................................................................10
4. Operation.....................................................................................................11
Control Panel Description........................................................................................... 11
Control Options .......................................................................................................... 11
Programming.............................................................................................................. 11
DMX Addressing................................................................................................................11
DMX Personality................................................................................................................11
Master/Slave......................................................................................................................12
Static Colors......................................................................................................................12
Auto Play...........................................................................................................................12
Custom Play......................................................................................................................12
Edit Custom.......................................................................................................................12
RGB to White Setting ........................................................................................................13
Whites Setting ...................................................................................................................13
Set Time and Date.............................................................................................................13
Set Schedule.....................................................................................................................13
Playing Schedule...............................................................................................................13
Password...........................................................................................................................14
Upload Customs................................................................................................................14
Reset.................................................................................................................................14
Menu Options............................................................................................................. 15
DMX Values ............................................................................................................... 17
EFFECT ............................................................................................................................17
DMX Values ............................................................................................................... 18
RGB...................................................................................................................................18
RGB + D............................................................................................................................18
RGB + DMS.......................................................................................................................18
RGB + LINE.......................................................................................................................18

Table of Contents
ii LΩGIC™ 16X36 User Manual (Rev. 06)
5. Technical Information.................................................................................19
System Maintenance.................................................................................................. 19
Product Repairs.......................................................................................................... 19
Troubleshooting Guide............................................................................................... 20
LED Disclaimer........................................................................................................... 21
LED Life.............................................................................................................................21
LED Binning.......................................................................................................................21
Color Rendering Index (CRI).............................................................................................21
Returns Procedure..................................................................................................... 22
Claims......................................................................................................................... 22
Contact Us.................................................................................................................. 22
Technical Specifications............................................................................................. 23

Introduction
LΩGIC™ 16X36 User Manual (Rev. 06) 1
1. Introduction
This icon
indicates useful,
although non-
critical information.
This icon
indicates
important
installation or
configuration information.
Failure to comply with this
information may prevent
the product from
functioning correctly.
This icon
indicates critical
installation,
configuration, or operation
information. Failure to
comply with this
information may render
the product partially or
completely inoperative,
damage third-party
equipment, or cause harm
to the user.
The term “DMX”
used throughout
this document
refers to the USITT
DMX512-A transmission
protocol.
What is Included
•One LΩGIC™ 16X36
•One RJ-45 to 3-pin DMX male adapter (input)
•One RJ-45 to 3-pin DMX female adapter (output)
•Sixteen - RJ-45 coupler
•One Power Cord
•Warranty Card
•Quick Start Guide
Unpacking Instructions
Immediately upon receiving a product from ILUMINARC®, carefully unpack the carton. Check
the contents of the box to ensure that all parts are present and that they are in good condition. If
any part appears damaged from shipping, or if the carton shows signs of mishandling, see the
Claims section in the Technical Information chapter.
Text Conventions
Convention Meaning
1~512
A range of values in the text
50/60
A set of mutually exclusive values in the text
“ILUMICON UM”
The name of another publication or manual
<ENTER>
A button on the products control panel
Settings
A product function or a menu option
MENU > Settings
A sequence of menu options
1~10
A range of menu values from which to choose in a menu
Yes/No
A set of two mutually exclusive menu options in a menu
ON
A unique value to enter or select in a menu

Introduction
2 LΩGIC™ 16X36 User Manual (Rev. 06)
There are no
user serviceable
parts inside this
product. Any reference to
servicing it you may find
from now on in this User
Manual will only apply to
properly ILUMINARC®
certified technicians. Do
not open the housing or
attempt any repairs
unless you are Certified to
do so.
Please refer to all
applicable local
codes and
regulations for the proper
installation of this product.
Keep this manual
for future
consultation. If
you sell this product to
another user, make sure
that they also receive this
manual.
In the unlikely
event that your
LΩGIC™ 16X36
may require service,
please contact
ILUMINARC®Technical
Support.
Safety Notes
Please read all the following safety notes carefully because they include important information
on how to install, use, and maintain this product safely.
Personal Safety
•Avoid direct eye exposure to the light source while the product is on.
•Always disconnect this product from its power source before servicing.
•Always connect this product to a grounded circuit to avoid the risk of electrocution.
Mounting and Installation
•This product is for indoor use only! To prevent risk of fire or shock, do not expose this
product to rain or moisture.
•Make sure there are no flammable materials close to this product while operating.
Power and Wiring
•Always make sure that you are connecting this product to the proper voltage, as per the
specifications in this manual or on the product’s sticker.
•Never connect this product to a dimmer pack.
•Make sure that the power input cable is not cracked, crimped, or damaged.
•Never disconnect this product by pulling or tugging on the power input cable.
Operation
•The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate this product
at a higher temperature.
•In case of a serious operating problem, stop using this product immediately!

Product Description
LΩGIC™ 16X36 User Manual (Rev. 06) 3
2. Product Description
The LΩGIC™ 16X36 product is the power supply and control for the LΩGIC™ series of
products.
The LΩGIC™ 16X36 consists of seven (7) personalities for the RGB mode,
which are
configurable from the control panel. The output of the LΩGIC™ 16X36 is sixteen RJ-45 type
connections. The DMX input and output is on the rear panel and also uses a RJ-
45 type
connection.
Features
•1, 2, 3, 4, 6, 9, or 48-channel DMX control
•Operating modes:
1-channel: RGB, dimmer (no individual RGB adjustments)
3-channel: RGB control (individual RGB adjustments)
4-channel: RGB control, dimmer
6-channel: RGB control, dimmer, color macro, strobe
9-channel: RGB control, dimmer, color macro, strobe, auto + custom, auto speed, zone
selection
48-channel: RGB control, line control
•16 output lines
•RGB color mixing with or without DMX control
•Automated and customizable programs
•Recall auto and custom programs via master/slave or DMX
Additional Features
•Master/Slave (RJ-45)
•Static Playing
•RGB and white color calibration
•Schedule playback with time clock functions
•LCD display with password protection

Product Description
4 LΩGIC™ 16X36 User Manual (Rev. 06)
Product Overview
Signal
Indicator
Power
Indicator
DMX
In
DMX
Out
LED
Outputs
RS-232
(Future Use)
Control
Panel
Power
Input
Mounting
Bracket
Fuse
Holder

Installation
LΩGIC™ 16X36 User Manual (Rev. 06) 5
3. Installation
Always connect
the LΩGIC™
16X36 to a
protected circuit with an
appropriate electrical
ground to avoid the risk of
electrocution or fire.
Never connect
the LΩGIC™
16X36 to a
rheostat (variable resistor)
or dimmer circuit, even if
the rheostat or dimmer
channel serves only as a
0 to 100% switch.
Make sure to
disconnect the
products power
cord before replacing a
blown fuse, and always
replace it with a fuse of
the same type and rating.
AC Power
The LΩGIC™ 16X36 has an auto-ranging power supply that can work with an input voltage
range of 100~240 VAC, 50/60 Hz.
Make sure that you are connecting this product to the proper voltage, as per the specifications in
this guide, the product’s user manual, or on the product’s sticker.
Power Consumption
To determine the power requirements for the LΩGIC™ 16X36 see the label affixed to the
side of the product. Alternatively, you may refer to the corresponding specifications chart in
the Technical Information chapter of this manual.
The listed current rating indicates the maximum current draw during normal operation.
AC Plug
The LΩGIC™ 16X36 comes with a power input cord that enters through a strain relief boot
that is then hardwired to the inside of the product. The other end of the power cord is bare-
ended. Please use the table below to wire the new plug.
Connection Wire (US) Screw Color (US) Wire (Europe)
AC Live
Black
Yellow or Brass
Brown
AC Neutral
White
Silver or Gray
Blue
AC Ground
Green/Yellow
Green
Green/Yellow
Fuse Replacement
1. Disconnect the fixture from the power outlet.
2. With a Phillips #2 head screwdriver, unscrew the fuse holder cap from its housing.
3. Remove the blown fuse and replace it with a good fuse of the same type and rating (F
10 A, 250 V).
4. Screw the fuse holder cap back in its place and reconnect power.

Installation
6 LΩGIC™ 16X36 User Manual (Rev. 06)
The products
must be linked
using DMX cable
in a daisy chain (serial)
fashion. To comply with
the EIA-485 standard, no
more than 32 products
should be connected on
one daisy chain without
using a DMX optically-
isolated splitter. Doing
otherwise may result in
deterioration of the digital
DMX signal.
USITT
recommends
limiting the total
length of the DMX cable
(from the first
product/controller to the
last product) to 300 ~ 455
m (985 ~ 1,500 ft).
The Operation
chapter of this
manual provides
detailed instructions on
how to configure the
Master and Slave
products.
DMX Linking
The LΩGIC™ 16X36 uses a CAT5 cable to link to other products.
•The first product of each set of LΩGIC™ 16X36 products must connect to the DMX
controller with a CAT5 to XLR male adapter.
•The last LΩGIC™ 16X36 product must use a CAT5 to XLR female adapter to
continue the serial link to other DMX compatible products.
You may link the LΩGIC™ 16X36 to a DMX controller using a CAT5 cable. If using other
DMX products compatible with the LΩGIC™ 16X36, you can control them individually with a
single DMX controller.
If you are not familiar with the DMX standard, or if you need information about the DMX
cables needed to link the LΩGIC™ 16X36 to a DMX controller, you may download the “DMX
Primer” document from the ILUMINARC® web site: www.iluminarc.com.
Master/Slave Linking
The Master/Slave mode allows a LΩGIC™ 16X36 product (the master) running a
preconfigured program to control several other LΩGIC™ 16X36 products (the slaves) without
requiring a DMX controller. In this mode, all the slave products will operate in unison with the
master product.
When in Master/Slave mode, the LΩGIC™ 16X36 products link to each other using the
standard CAT5 DMX connection.

Installation
LΩGIC™ 16X36 User Manual (Rev. 06) 7
Do not use the
splitter as a
coupler.
All cables must
be terminated to
a fixture
LΩGIC™ 16X36 Product Linking
Use this method when connecting a set of one or more LΩGIC™ 16X36 products to the same
DMX cable. This is the simplest method to connect multiple products to the same DMX
controller.
1. Connect the RJ-45 plug of the DMX to RJ-45 adapter to the “DMX In” RJ-45 jack on
the first LΩGIC™ 16X36product.
2. Connect the XLR male connector of the DMX to RJ-45 adapter directly to the “DMX
Out” (female) connector on the DMX controller or to the DMX cable coming from the
DMX controller.
3. Connect one of the RJ-45 plugs of the signal patch cable to the “DMX Out” RJ-45 jack
on the first LΩGIC™ 16X36 product.
4. Connect the other RJ-45 plug of the signal patch cable to the “DMX In” RJ-45 jack on
the second LΩGIC™ 16X36 product.
5. Continue linking the LΩGIC™ 16X36 products using more signal patch cables, as
shown in the diagram below.
ILUMINARC recommends using a signal terminator after the last LΩGIC™ 16X36
product.The easiest way to assemble a signal terminator is by soldering or crimping a 120 ohms
resistor between the terminals corresponding to DATA + and DATA – on a RJ-45 jack.
Another method consists in soldering the 120 ohms resistor to a short cable coming out of a RJ-
45 plug. Once assembled, connect the terminator to the “DMX Out” connector of the last
LΩGIC™ 16X36 product.
RJ-45 to DMX adapter
LED patch cable
Signal patch cable
LED patch cable
Terminator or RJ-45 to DMX adapter
Optional splitter
RJ-45 Coupler
(Included with controller)

Installation
8 LΩGIC™ 16X36 User Manual (Rev. 06)
When
connecting
LΩGIC™
products to the
LΩGIC™ 16X36
controller, do not exceed
the maximum of 12 LEDs
per output channel (36
LEDs total for the output
line).
Maximum Output Line Loading
The LΩGIC™ 16X36 product has sixteen (16) output lines. This means that the user can
combine various output lines to create zones. Each output line has three channels. Each channel
can support up to 12 LEDs. As a result, the maximum number of LEDs supported by an output
line is 36.
Inside the LΩGIC™ products, the LEDs are grouped in clusters of three LEDs each. In an LED
cluster, each LED connects to an individual output channel from the LΩGIC™ product. When a
product has more than one cluster, the same output channel supports as many LEDs as clusters
the product has.
Please see the guide below for the output line loading. This table shows the maximum number
of a single type of products that can be loaded onto each of the LΩGIC™ 16X36’s output lines.
MODEL NAME TOTAL LED’S
MAX.NUMBER OF
CONNECTED PRODUCTS
PER OUTPUT
Ilumiline LΩGIC™ 36 RGB 36 1
Ilumiline LΩGIC™ 24 RGB 24 1
Ilumiline LΩGIC™ 24 Optic RGB 24 1
Ilumiline LΩGIC™ 12 Optic 12 3
Ilumiline LΩGIC™ 12 12 3
Ilumipod LΩGIC™ 12 Optic 12 3
Ilumipod LΩGIC™ Tri-4 12 3
Ilumipod LΩGIC™ 6 Optic 6 6
Ilumipod LΩGIC™ 3 Optic 3 12
Ilumipod LΩGIC™ Tri-1 3 12
You may also combine different products together, as long as you do not exceed the maximum
of 36 LEDs per output line. Please see the following example of a possible combination.
Ilumipod LΩGIC™ Tri-4 12 X 2 = 24 2 products
Ilumipod LΩGIC™ 6 Optic 6 x 2 = 12 2 products
Total 36 LEDs 4 products

Installation
LΩGIC™ 16X36 User Manual (Rev. 06) 9
Cable Connections
RJ-45 Plug 3-pin XLR Male 5-pin XLR Male
Pin 1: Not Used
Pin 2: Not Used
Pin 3: Not Used
Pin 4: Not Used
Pin 4: Not Used
Pin 5:
+5 V
Pin 5: Not Used
Pin 6: Data + Pin 3: Data + Pin 3: Data +
Pin 7: Data -Pin 2: Data -Pin 2: Data -
Pin 8:
GND
Pin 1:
GND
Pin 1:
GND
RJ-45 Plug RJ-45 Plug
Pin 1: Not Used Pin 1: Not Used
Pin 2: Not Used Pin 2: Not Used
Pin 3: Not Used Pin 3: Not Used
Pin 4: Not Used Pin 4: Not Used
Pin 5: +5 V Pin 5: +5 V
Pin 6: Data + Pin 6: Data +
Pin 7: Data -Pin 7: Data -
Pin 8: GND Pin 8: GND
Pin # Wire Color Function
1
White/Orange
Red LED +
2 Orange/White Green LED +
3 White/Green Blue LED +
4
Blue/White
Not Used
5 White/Blue Red LED -
6 Green/White Green LED -
7 White/Brown Blue LED -
8
Brown/White
Not Used
XLR
(male)
3-pin
Signal Patch cable: Used for linking two LΩGIC™ 16X36products
LED Patch Cable: Used to link the LΩGIC™ 16X36 to its products.
RJ-45 Plug
DMX XLR (male)
XLR
(male)
5-pin
RJ-45 Plug Pin Assignment
View facing pins

Installation
10 LΩGIC™ 16X36 User Manual (Rev. 06)
Make sure to
mount this
product away
from any flammable
material as indicated in
the Safety Notes.
Please consult
local electrical
code compliance
and regulations for any
additional installation
restrictions.
Mounting
Before mounting this product, read and follow the safety recommendations indicated in the
Safety Notes section (page 2 of this manual).
Orientation
Always mount this product in any safe position while making sure that there is adequate
room around it for ventilation, configuration, and maintenance.
Installation
The LΩGIC™ 16X36 consists of a single product with 4 mounting points. ILUMINARC®
recommends following the general guidelines below when mounting the LΩGIC™ 16X36.
•When selecting an installation location, consider ease of access to the product for
operation, programming adjustments, and routine maintenance.
•Never mount the product in places where rain, high humidity, extreme temperature
changes, or restricted ventilation may affect it.
•Make sure that the location where you are mounting the product can support its weight.
Please see the Technical Specifications section of this manual for the weight
requirement of this product.
Procedure
The LΩGIC™ 16X36 has four (4) 5mm screw holes built into the casing which serves as
mounting points. Use Four (4) screws to attach the product to a flat, dry surface. Make sure
that you can access the product for maintenance and programming.

Operation
LΩGIC™ 16X36 User Manual (Rev. 06) 11
4. Operation
When running
the product
using a DMX
controller, make sure that
the Menu>Run is set to
DMX.
Control Panel Description
Button Function
<MENU>
Exits from the current menu or function
<ENTER>
Enables the currently displayed menu or sets the currently selected value in
to the current function
<UP>
Navigates upwards through the menu list and increases the numeric value
when in a function
<DOWN>
Navigates downwards through the menu list and decreases the numeric
value when in a function
Control Options
You can set the LΩGIC™ 16X36 start address in the 001~512 DMX range. This allows for the
control of up to 10 products in the 48-channel RGB+LINE personality.
Programming
Refer to the Menu Options section to learn how the menu options relate to each other. The
Menu Options section has a Main level and a variable number of programming levels for each
option.
•To go to an option in the Main level, press <MENU> repeatedly until the option
shows on the display. Press <SET> to select. This will take you to the first
programming level for that option.
•To select an option or value within the current programming level, press <UP> or
<DOWN> until the option or value is displayed. Press <SET> to accept. If there is
another programming level, you will see that level’s first option. If not, you will see
the selected value.
•To exit to the previous menu level, press <MENU>.
DMX Addressing
1. Go to MENU>DMX ADDRESS.
2. Select the starting address [001~512].
3. Go to MENU >OPERATION.
4. Select DMX.
DMX Personality
1. Go to MENU>PERSONALITY and select any DMX personality.
2. Make sure to rearrange the DMX addresses of all products in the current DMX
universe to avoid address overlapping.

Operation
12 LΩGIC™ 16X36 User Manual (Rev. 06)
AUTO 01~10 are
fully configured
programs and
cannot be modified.
However, CUSTOM
01~10 programs are fully
customizable (see Edit
Custom).
AUTO 01~10
consist of two (2)
different, fully
configured programs
giving the user a total of
twenty(20) different auto
programs to choose from.
Master/Slave
On the Master product:
1. Go to MENU>OPERATION and select DMX.
2. Go to MENU>PLAY AUTO and select any Auto program.
On each of the Slave products:
1. Go to MENU>OPERATION and select SLAVE.
The slave products will follow the program played by the Master.
Static Colors
1. Go to MENU>PLAY STATIC.
2. Select an output line L [1~16] or LALL
3. Select a color or effect RED, GREEN, BLUE, DIMMER, and STROBE.
4. Select a color value [000~255] or a strobe frequency [0~20].
Auto Play
1. Go to MENU>PLAY AUTO.
2. Select a program RGB, or RGBL [01~10].
Custom Play
1. Go to MENU>CUSTOM.
2. Select a program CUSTOM [01~10].
Edit Custom
1. Go to MENU>EDIT.
2. Select a program C-[01~10].
3. Select a scene S-[01~20].
4. Select a color R, G, or B.
5. Configure the color value [000~255].
6. Repeat steps 4 and 5 for the other colors.
7. Configure the strobe frequency S-[00~20].
8. Configure the Step and Fade timers [000~255].
9. Repeat steps 4 to 8 for the other scenes.

Operation
LΩGIC™ 16X36 User Manual (Rev. 06) 13
.
RGB to White Setting
When RGB TO W is active, the product will automatically use the RGB values for a
balanced white look. When inactive, the product will use the most powerful intensity.
1. Go to MENU>SETTTINGS>RGB TO WHITE.
2. Select YES or NO.
Whites Setting
1. Go to MENU>SETTINGS>CALIBRATION.
2. Select a white color WHITE 1~9 or RGB TO WHITE.
3. Set a color R, G, or B.
4. Configure the color value [000~255].
5. Repeat steps 2thru 4 for the other RGB colors to obtain a white color.
Set Time and Date
1. Go to MENU>SETTINGS>CLOCK>EDIT TIME.
2. Set Year, Day Of Week, Day, Month, Hour, Min, and Sec.
Set Schedule
1. Go to MENU>SCHEDULE. A day of the week or “EVERYDAY” will show on the
LCD.
2. Select DOW or EVERYDAY.
3. Select NO. [01~10].
4. Set CUSTOM [01~10], STATIC, RGBL [01~10], RGB [01~10], or PLAY NONE.
5. Set Start time [00:00 to 23:59].
Set End time [00:00 to 23:59].
Playing Schedule
1. Go to MENU>PLAY SCHEDULE.

Operation
14 LΩGIC™ 16X36 User Manual (Rev. 06)
The Password is
fixed by default. It
is not able to be
changed.
If the upload is
successful, all the
products will
show ”Success” on the
LCD.
Password
When KEYLOCK is active, the product will ask you to enter the password (<UP>,
<DOWN>, <UP>,and <DOWN>) after 30 seconds of control panel inactivity or upon
power up.
1. Go to MENU >SETTINGS.
2. Select ON/OFF.
Upload Customs
1. Set all products that are going to receive the upload to SLAVE operation.
2. Disconnect the products from the DMX controller.
3. On the product whose custom programs you are going to copy, got to MENU
>SETTINGS and select UPLOAD.
4. Enter the password and press <ENTER>for the upload to start.
Reset
1. Go to MENU>SETTINGS.
2. Select RESET CUSTOM (resets custom programs), RESET SCHEDULE (resets
schedule), or RESET ALL (resets entire product to factory default).
3. When YES shows, press <ENTER>.

Operation
LΩGIC™ 16X36 User Manual (Rev. 06) 15
Menu Options
Main Programming Steps Instructions
1. Play auto RGB 1~10 RGBL 1~10 1~255 Choose from 10 automatic programs
2. Play
custom
CUSTOM 1~10 Choose from 10 user-defined programs
3. Play Static L1~16
or
LALL
RED
0~255 Configure and/or play a single step program
GREEN
BLUE
DIMMER
STROBE 0~20
4. Play
schedule
SCHEDULE PLAYING! Play scheduled program
5. DMX
address
001~512 Sets DMX starting address
6. Personality
EFFECT 9-channel mode
RGB 3-channel mode
RGB+D 4-channel mode
RGB+DMS 6-channel mode
RGB+LINE 48-channel RGB control over individual lines
7. Edit
custom C-1~10
(custom) S-1~20 (scene)
R
G
B
0~255 Combine Red, Green, and Blue to generate a custom color
S 0~20 Set the strobe frequency
T 0~255 Set the on time
F Set the fading time
8. Settings
PASSWORD ON/OFF Turn password protection on after 30 seconds of being idle
ALLOW EDIT
YES/NO
Reserved for future use
RESET ALL Default all settings
RESET CUSTOM Erase the custom programs
RESET SCHEDULE Erase the schedule
UPLOAD PASSWORD? [Enter Password] Transfer custom programs from master to slave products
CLOCK
TIME NOW View the DOW, date, and time
EDIT TIME
YEAR 00~99
Edit the DOW, date, and time
DOW SU~SA
DAY 01~31
MONTH 00~12
HOUR 00~23
MIN 00~59
SEC
CALIB-
RATION
WHITE 1~9 R
G
B 0~255 Modify the White macros
RGB TO
WHITE
Configure RGB to WHITE values
RGB TO WHITE YES/NO
[Yes]RGB TO WHITE defines output color when RGB
faders are at “255”
[No]Max. intensity when RGB faders are at “255”
Continues on the next page

Operation
16 LΩGIC™ 16X36 User Manual (Rev. 06)
Continued from previous page
Main Programming Steps Instructions
9. Operation
DMX
Work with a DMX controller
SLAVE
Slave mode
EASY PLAY
Optional remote
10. Schedule
SUNDAY~
SATURDAY
(Different
schedules for
each DOW) No.1~10
RGB
RGBL
CUSTOM 1~10
After selecting DOW, schedule #, and program, enter
starting and ending time [00:00~23:59]
EVERYDAY
(Same
schedule for
every DOW)
STATIC
PLAY NONE
11. Patch PATCH 1~6
RGB
RGBL
CUSTOM
1~10 For future use