ILVE Roma User manual

RANGECOOKER
INSTALLATION MANUAL
ROMA - MILANO - MAJESTIC ROMA - MAJESTIC MILANO
06 - 07 - 08 - 09 - 10 - 12 - 15
INSTALLATION AND MAINTENANCE
EN
cod. EI33960030000EN
32/2019
ZONA PER TARGHET TA

2

3
INFORMATION - Important notes
INSTALLATION
Installation of the cooker
Room ventilation
Installation of the cooker
How to install the xing bracket
ELECTRICAL CONNECTIONS
Groups of cooking
Induction cookers
GAS INSTALLATION
GAS CONNECTIONS
By the Qualied installer
LPG CONVERSION
Replacement of the injectors for all models
ADJUSTMENT
Adjustments minimun GAS ow
KITCHEN TABLE
ROMA - MILANO - MAJESTIC ROMA MAJESTIC MILANO
WIRING DIAGRAM
Key
INDEX
4
5
5
5
6
7
8
8
9
9
10
10
11
11
12
12
13
14
14

4
INFORMATION
Important notes
ATTENTION
LEAKING GAS
THE INSTALLER MUST GIVE THE FOLLOWING INFORMATION TO THE USER
• Verify the integrity of the appliance and the presence of all the product documen-
tation.
• Verify that the appliance has all the expected accessories.
• Verify the correct utilization of the appliance (use of the oven, thermostat and igni-
tion of the burners).
• Suggest to note the serial number and warranty information
• Request that a periodic maintenance service has to be carried out at least every
two years to maintain a fully functioning appliance.
In the case of leaking gas, close the main gas tap and disconnect the product
from the mains. Call the ILVE service team immediately.

5
ATTENTION
Measures to be
respected
Directives/regulations
Room ventilation
The appliance weighs more than 60 kg, therefore it must be moved using appropriate
lifting equipment
Do not drag the cooker as this will bend the supporting feet. Lift the appliance into posi-
tion with correct lifting equipment.
- This appliance is in compliance with the applicable CE standards.
- Installation must only be carried out by qualied persons in compliance with
the regulations and standards in force: UNI 7129-1, UNI 7129-2, UNI 7129-3, UNI
7129-4, UNI 7131.
This is a type “A” appliance which does not need to be joined to an exhaust system for
combustion waste however ILVE strongly recommend that it is installed under a range
hood or other smoke extraction system in compliance with the gas safe regulations. The
knowledge and consultation of the standards are a key factor for a qualied technician.
Indicatively the amount of air necessary for burner combustion is 2 m3/h for each KW of
nominal power installed (see plate).
Should the appliance be subjected to intensive and prolonged use, supplementary ven-
tilation may be necessary; in such cases open a window or increase the extractor fan’s
power.
INSTALLATION
Installation of the cooker
a
a (mm) models
600 P06... L06...
700 P07... M07...
800 P08...
900 P09... L09...
911 M09...
a (mm) models
1000 PD10... M10...
1200 P12...
1211 M12...
1500 P15...
1511 M15...

6
- The appliance can be installed singularly: class 1.
- The appliance can be installed between two pieces of furniture: class 2/1.
- The cooker is protected against excessive overheating, so it may be installed next to
furniture with a height no higher than that of the worktop. The wall in contact with the
back of the cooker must be made of re-resistant material. To install the cooker correct-
ly, take the following precautions.
A. Any furniture in the vicinity of the cooker with a height higher than that of the worktop
must be at least 50mm from the edge of the cook top;
B. The extractor hood must be installed in the way indicated in its instructions booklet,
and always at a minimum distance of 650 mm from the top of the hob;
C. If the cooker is installed under a wall unit, the minimum distance between this unit
and the worktop must be 700 mm.
INSTALLATION
Installation of the cooker
Positioning of the
appliance between
furniture
Min.
50 mm
Min.
650 mm
Min.
700 mm
G
E
AB
e
g
A B e g
M30 230 mm 90 mm 120 mm 80 mm
M09 230 mm 90 mm 190 mm 140 mm
MD10 230 mm 90 mm 140mm 95 mm
M12 230 mm 90 mm 150 mm 110 mm
M15 230 mm 90 mm 144 mm 150 mm
A B e g
P06 230 mm 90 mm 130 mm 80 mm
P09 230 mm 90 mm 240 mm 150 mm
PD09 230 mm 90 mm 140 mm 80 mm
PD10 230 mm 90 mm 140 mm 80 mm
P12 230 mm 90 mm 230 mm 110 mm
P15 230 mm 90 mm 200 mm 170 mm

7
Model: 60, 70, 80, 90 cm.
ATTENTION
- Unpack the cooker and mount the feet by adjusting the height.
- Measure the height from the oor to the top edge of the back-cross bar (picture 5) and
add 15mm.
- Fix the supporting bracket in the centre of the cooker aperture on the supporting wall.
- Check that the cooker is tight against the back wall to avoid tipping.
The anti-turnover system is assured only if the cooker is installed with the back
tight against the back wall.
INSTALLATION
How to install the xing bracket

8
ATTENTION
Rules for installation
ATTENTION
The instructions below are intended for the skilled technician who will install the cooker,
regulate it and perform technical maintenance and who will ensure that these operations
are carried out in the most correct way possible, in compliance with the regulations in
force.
Important: the cooker must be disconnected from the electric supply before per-
forming all regulating or maintenance operations.
• Installation must be carried out by a competent technician, fully complying with the legi-
slation in force regarding electrical installations. Otherwise, the manufacturer disclaims
any responsibility. You will nd your appliance’s wiring diagram in this booklet.
• The appliances are prepared for connection to the voltage shown on the data plate.
• Before connecting the appliance to the mains check that:
-the main cooker switch is able to support the appliance’s load(see dataplate);
-the power supply should be earthed as per the current regulations.
The appliance is supplied with a cable but without a plug: the connection must be made
taking into account that the green-yellow cable is the earth conductor and it must
never be interrupted.
The main cooker switch must be visible and easily reachable so that the appliance can
easily be disconnected.
It is necessary that:
- the installation can support the equipments load. (see data plate)
- the power supply system must have an efcient earth.
- the cooker switch must have a minimum 3 mm, double pole contact opening and must
be easily reachable once the appliance has been installed.
- means for disconnection must be incorporated in the xed wiring in accordance with
current regulations.
The yellow-green earth wire must never
be interrupted even by the switch.
The power cable should be positioned
so that it does not come into contact with
surfaces that have a temperature of 50 °C
higher than the environment. In case repla-
cement of the power cable is necessary,
contact the support service.
ELECTRICAL CONNECTIONS
Groups of cooking

9
The power supply cable should not reach a 50°C temperature above the ambient temperature.
Due to conned space available at the rear of the cooker, the cooker cannot currently be
installed to GB Gas Safe regulations without leaving a gap in between the cooker and
the rear wall. The cooker cannot be tted ush.
Gas safe regulations stipulate:
• Height of bayonet on the wall needs to be 750mm from the oor.
• The hose cannot touch the oor
• Cannot have any strain or tension on the hose
• PIC (Plug In Connector) needs to point down.
Gas safe regulations can be overridden by manufacturer instructions, as long as safe to do so.
After speaking to Gas Safe on 22.07.19 we have learned that as long as the manufactu-
rer states that it is possible to do so, the bayonet can be tted closer to the oor.
For a low level, ush installation, the bayonet can be tted between 180mm – 250mm
from the oor, as long as the pipe is under no strain or tension. This will allow the co-
okers to be tted with the gas hose running along the base of the cooker. This will also
mean that the PIC can be connected and disconnected by removing the storage drawer
and accessing from the front of cooker. This will make installation easier in general.
ATTENTION
Data concerning the
power cable
Gas cooker installation
1st Installation Option
To Manufacturers
regulations
ELECTRICAL CONNECTIONS
Induction cookers
GAS INSTALLATION
POWER SUPPLY CONNECTION CABLE SECTION CABLE TYPE
Mod. P..I06 230V a.c. 1P+N
50/60 Hz 1 phase + N 3x4 H05RR
Mod. P..I09..
M..I09..
230V a.c. 1P+N
50/60 Hz 1 phase + N 3x6 H07RN
Mod. PDI09.. 230V a.c. 1P+N
50/60 Hz 1 phase + N 3x6 H07RN
Mod. MDI10.. 230V a.c. 1P+N
50/60 Hz 1 phase + N 3x10 H07RN
Mod. PDI10.. 230V a.c. 1P+N
50/60 Hz 1 phase + N 3x10 H07RN
ILVE Gas Cooker installation
Due to confined space available at the rear of the cooker, the cooker cannot currently be
installed to GB Gas Safe regulations without leaving a gap in between the cooker and the
rear wall. The cooker cannot be fitted flush.
Gas safe regulations stipulate:
Height of bayonet on the wall needs to be 750mm from the floor.
The hose cannot touch the floor
Cannot have any strain or tension on the hose
PIC (Plug In Connector) needs to point down.
Gas safe regulations can be overridden by manufacturer instructions, as long as safe to do
so.
1st Installation Option – To Manufacturers regulations
After speaking to Gas Safe on 22.07.19 we have learned that as long as the manufacturer
states that it is possible to do so, the bayonet can be fitted closer to the floor.
For a low level, flush installation, the bayonet can be fitted between 180mm –250mm from
the floor, as long as the pipe is under no strain or tension.
This will allow the cookers to be fitted with the gas hose running along the base of the
cooker. This will also mean that the PIC can be connected and disconnected by removing the
storage drawer and accessing from the front of cooker. This will make installation easier in
general.
180mm –
250mm A.F.F.L
UNIT
UNIT
170mm
We recommend no
pipes to be fitted
here if flush.

10
a) CLASS (Subclass 2/1 cooker recessed between furniture)
The apparatus must be connected to the gas mains by means of PIC exible metal
hose (maximum length 2 metres) suitable for gas appliances.
The connection pipes and their maximum lengths must conform to the applicable stan-
dards (UNI CIG 9891), which are replaced before expiry (if indicated on the tube) and
connected to the device by means of the ISO R228 threaded tting (Fig. A) with the
interposition of the sealing gasket, or ISO R7 (Fig. A) with metallic seal on the thread
(sealing materials may be used as long as they are suitable for gas connections)
b) CLASS (for LPG installation)
The cooker must be installed according to LPG gas safe regulations. The LPG conver-
sion must be carried out by a competent technician as per the instructions manual.
The appliance is delivered to operate as indicated on the label on the appliance: CAT.
II2H3 + = GAS G20 mbar; GAS G30/31 = 30/37 mbar.
For LPG conversion, see page 11
Any maintenance operation, etc. It must be carried out by an authorized technician after
disconnecting the appliance from the mains and closing the gas supply.
GAS CONNECTIONS
By the qualied installer
Thread: ISOR7
Thread: ISOR228
Seal
Fig. A
Instructions
(UNI 7129/7131)
LPG conversion
ATTENTION

11
Procedure:
SR - R - P
Procedure:
DCC
Burners SR – R – P:
• unscrew injectors “U” using a 7mm spanner (g. 1) and replace them with those for
the new gas according to table number 2 on page 20.
DCC – Dual burners
• unscrew the 2 screws “P” and remove cover “C” g.2.
• unscrew injectors “U” using a 7 mm spanner (g.3, g.4) and replace them with
those for the new gas according to table number 1 below 13.
LPG CONVERSION
Replacement of the injectors for all models
2
1
3
4
U
UU

12
Adjustments
Burners on the hob
Burners in the gas oven
When installing the cooker, you must check that the minimum gas ow of the burners on
the hob and in the oven is correctly regulated.
If the type of gas is changed it is indispensable to adjust the minimum ow. The regula-
ting procedure is as follows.
1. Light one burner at a time and turn the ame
up to maximum.
2. Remove the knob of the corresponding gas
tap and insert a screwdriver in the end part of
the tap or in the screw (g. A1,A2).
3. Turn the tap to minimum position.
4. Unscrew, turning to the left, to increase the
ame, or screw to the right to decrease it.
5. If a liquid gas is used (Butane - Propane), the
regulating screw must be fully screwed in.
1. Remove the bottom shelf of the oven.
2. Light the burner and leave it at maximum for
about 10minutes with the oven door closed.
3. Turn the knob to minimum and, still with the-
door closed, check whether the ames have
lowered but are still burning steadily (about 3-4
mm).
4. Remove the knob of the thermostat. Insert
a screwdriver on the proper screw (g. B):
turn anti-clockwise to increase the minimum,
clockwise to decrease it. The ame must be
steady and homogeneous.
5. If the ames are not well adjusted at minimum
level,repeat the procedure described above.
6. If a liquid gas is used (Butane - Propane), the
regulating screw must be fully screwed in.
ADJUSTMENTS
Adjustments minimun GAS ow
Fig. C2

13
P09
P07
P08
P09
PD09
PD10
P12
P15
M07
M09
MD10
M12
M19
N. 1
TABELLA CUCINE PROFESSIONAL
SR R P DCC 06 H3/G3 08/09 H3/G3
Qmax kW 1,80 3,00
3,10 / 3,00
(6)
4,30 / 4,20
(3)(4) 2,70 3,70
Qmax g/h 131 218 225
313
196 269
Qmin kW
0,40 / 0,53(1) / 0,45(2) 0,60 / 0,75(1) / 0,65(2) 1,10 / 1,20(1) / 1,10(2)
1,80 / 2,32
(1)
/ 2,00
(2)
Qmin g/h 29 / 39
(1)
/ 33
(2)
44 / 55(1) / 47(2) 80 / 87(1) / 80(2)
131 / 169
(1)
/ 145
(2)
G30/G31 28..30/37 mbar 0,68/0222 0,85/0222 0,87/0222
1,05/0222
0,44/0222 1,04/0222 0,80/0222 0,92/0222
G30/G31 50 mbar 0,58/0264 0,75/0265 0,75/0222
0,80/0315
0,43/0102 0,83/0315 0,68/0222 0,80/0222
G30 37 mbar 0,62/0222 0,82/0222 0,82/0222 0,95/0222 0,41/0222 1,00/0222 0,74/0222 0,86/0222
G20 20 mbar 0,97/0211 1,30/0103 1,30/0222 1,50/1048 0,70/0101 1,52/1048 1,17/0222 1,32/0332
G20 25 mbar 0,91/0211 1,10/0210 1,23/0222 1,50/0103 0,65/0101 1,50/0103 1,10/0222 1,24/0332
G25 20 mbar 1,05/0210 1,37/0332 1,42/0222 1,57/0332 0,72/0306 1,64/0332 1,30/0222 1,48/0332
G25 25 mbar 0,98/0210 1,26/0332 1,35/0222 1,50/0332 0,75/0306 1,50/0332 1,25/0222 1,40/0332
G2.350 13 mbar 1,26/0210 1,64/0332 1,64/0332 2,10/1048 0,91/210 2,10/1048 1,70/0222 1,90/0332
G25.1 25 mbar 0,98/0210 1,25/0309 1,28/0332 1,52/0332 0,71/0306 1,52/0332 1,25/0222 1,43/0332
G25.3 25 mbar 0,94/0210 1,26/0332 1,28/0332 1,48/0332 0,75/0306 1,48/0332 1,20/0222 1,37/0332
G110 8 mbar 1,90/0224-2
2,60/0224-3
2,70/0224-6 3,50/00003 1,45/00004 3,50/00003 2,80/0222
2,80
(5)
/0222
G150.1 8 mbar 1,80/0224-2
2,60/0224-3
3,20
(5)
/0222
G30/G31 0,32 0,40 0,52 0,75 0,27 0,60
G20 REG REG REG REG REG REG
G25 REG REG REG REG REG REG
G2.350 13 mbar REG REG REG REG REG REG
G110/G120 REG REG REG REG REG REG
(1)=G30/G31 50 mbar
(6)=G2.350 13 mbar
(2)=G30 37 mbar (3)=G110/G120 8 mbar
(4)=G150.1 8 mbar
(5)= valve "A"
by-pass Ø mm
DUAL
5,00 / 4,20
(3)(4)
364
0,30 / 0,36
(1)
/ 0,31
(2)
22 / 26
(1)
/ 23
(2)
Ø mm
ADJUSTMENT
Kitchen table
ROMA - MILANO - MAJESTIC ROMA - MAJESTIC MILANO

14
WIRING DIAGRAM
Key
00 Black
11 Brown
22 Red
33 White
44 Yellow
45 Yellow-green
55 Grey
66 Blue
AA Electrical ignition transformer
C Switch
CP Probe connection
DU Dumper
EF Encoder functions
ET Encoder temperature
F Phase
K1 Earth wire for terminal board
K2 ” ” lower resistance
K3 ” ” for oven fan
K4 ” ” circular resistance
K5 ” ” upper resistance
K6 ” ” oven lamp 1
K7 ” ” oven lamp 2
K8 ” ” rotisserie
K9 ” ” cooling fan
K10 ” ” selector
K11 ” ” oven thermostat
K12 ” ” programmer/timer
K13 ” ” grill
K14 ” ” el. hotplate
K15 ” ” frame
K16 ” ” barbecue
K17 ” ” fryer
L1 oven lamp
L2 oven lamp
MTerminal board
MA Electrical ignition microswitch
MD Grill microswitch
MG Rotisserie
MP Door microswitch
N Neutral
NTC
Temperature probe
PTimer/Programmer
P
Timer/Clock
P1...6 Induction hotplate
PE Electric hotplate
PT1000
Temperature probe
R1 Upper heating element
R2 Lower heating element
R3 Grill heating element
R4 Circular heating element
R5 Barbecue heating element
R6 Fryer heating element
RE Energy regulator
S1 Oven warning light
S2 Mains power warning light
S3 Grill warning light
S4 Cooling fun warning
S5 Barbecue warning light
S6 El. hotplate warning light
S7 Turnsplit warning light
S8 Residual heat warning light
S9 Fryer warning light
SD
Display card
SI
Interface card
SPL Sparking plug
SP
Power board
SS
Probe card
T Grill thermostat
TF Oven thermostat
TR Fryer thermostat
TS Safety thermostat
TT Cooling fan thermostat
V Oven fan
VT Cooling fan
e-


  
 

 
  
     
  
 I  J
 K
E M
H p
 2 O
QUICK START

15
HOB GAS
BASIC INDUCTION HOB
AREA 5
WIRING DIAGRAM
MA MA MA MA MA MA MA

AA
SPL
66

11 66
o
o o o
F N 

16
WIRING DIAGRAM
P09I...E3
INDUCTION HOB AREA 4

17
INDUCTION HOB AREA 5
INDUCTION HOB AREA 6
WIRING DIAGRAM

18
WIRING DIAGRAM
P (06-07-30”-08-09)...E3
M(07-30”-09)...E3

19
WIRING DIAGRAM
M09I..E3
M12...E3

20
WIRING DIAGRAM
M12I...E3
M15...E3