imagistics im3510 User manual

im3510/im4510
Printing Operation Manual
©Imagistics International Inc. 2002
Printed in China
Printing Operation Manual
ZB3500260
07.04.02
www.imagistics.com
Imagistics International Inc.
100 Oakview Drive
Trumbull, CT 06611
TMTM
www.imagistics.com
2002G KS1
TINSE2314FCZZ Downloaded from www.Manualslib.com manuals search engine

Warranty
While every effort has been made to make this document as accurate and helpful as possible, Imagistics International
Inc. makes no warranty of any kind with regard to its content. All information included herein is subject to change
without notice. Imagistics International Inc. is not responsible for any loss or damages, direct or indirect, arising from
or related to the use of this operation manual.
© Copyright Imagistics International Inc. 2002. All rights reserved. Reproduction, adaptation or translation without
prior written permission is prohibited, except as allowed under copyright laws.
Trademark Acknowledgments
Microsoft Windows, MS-DOS, and Windows NT are trademarks of Microsoft Corporation in the U.S.A. and other
countries.
Macintosh, Power Macintosh, Mac OS, LaserWriter, and AppleTalk are registered trademarks of Apple Computer,
Inc.
IBM, PC/AT, and PowerPC are trademarks of International Business Machines Corporation.
Pentium is a registered trademark of Intel Corporation.
PCL is a trademark of the Hewlett-Packard Company.
PostScript® is a registered trademark of Adobe Systems Incorporated.
NetWare is a registered trademark of Novell, Inc.
All other trademarks and copyrights are the property of their respective owners.

0-1
1. The machine should be installed near an accessible
power outlet for easy connection.
2. Be sure to connect the power cord only to a power
outlet that meets the specified voltage and current
requirements. Also make certain the outlet is
properly grounded.
●For the power supply requirements, see the name
plate of the main unit.
3. Do not install your machine in areas that are:
●damp, humid, or very dusty
●exposed to direct sunlight
●poorly ventilated
●subject to extreme temperature or humidity
changes, e.g., near an air conditioner or heater.
4. Be sure to allow the required space around the
machine for servicing and proper ventilation.
INSTALLATION REQUIREMENTS
Improper installation may damage this product. Please note the following during initial installation and whenever the
machine is moved.
31-1/2"
(80cm)
23-5/8"
(60cm)
23-5/8" (60cm)
11-13/16" (30cm)
A small amount of ozone is produced within the printer during operation. The emission
level is insufficient to cause any health hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3)
calculated as an 8 hr. time-weighted average concentration.
However, since the small amount that is emitted may have an objectionable odor, it is
advisable to place the copier in a ventilated area.

0-2
Moving this machine
Lift this machine at the positions shown in the illustration below and carry it horizontally.
CAUTION
Two people are required to lift and carry this machine.
The center of gravity of the machine is slightly to the left of the center of the machine when viewed from the front. If a
duplex module is installed the center of gravity will be even further shifted to the left. When lifting the machine be
careful to steady it to prevent it from toppling. Also be sure that all covers and the duplex module are securely closed
and latched before lifting.
If a duplex module is installed, do not lift the machine by the module as it may come off causing it and the machine to
drop.
Remove the multi purpose drawer and lift at the positions shown in the illustration.
For removal and installation of the multi purpose drawer, see page 4-4. To avoid injury be sure to completely remove
the multi purpose drawer.
Front side Rear side
If the machine has been placed on a stand/paper drawer:
The stand/paper drawer is equipped with casters for moving. Unlock the adjusters of the stand/paper drawer and
gently move the machine taking care to steady it to prevent it from toppling.
For locking and unlocking the adjusters, see page 0-3.
CAUTIONS
●The center of gravity of this machine is a little deviated to the left from the center. If the machine is not equipped
with a multi purpose drawer or a stand/paper drawer, take care in opening the left side cover (or the duplex module)
not to cause toppling of the machine.
●Do not cover the ventilating holes of this machine. Do not install this machine in a location where these holes are
covered. If these holes are covered, heat will not be dissipated and a fire may be caused.
Remove the multi
purpose drawer
in advance.
Ventilating holes
INSTALLATION REQUIREMENTS

0-3
Fusing unit
Adjuster
Lock Release
CAUTIONS
1. Do not touch the photoconductive drum. Scratches
or smudges on the drum will cause dirty prints.
2. The fusing unit is extremely hot. Exercise care in
this area.
3. Do not look directly at the light source of the scanner
module. Doing so may damage your eyes.
4. Five adjusters are provided on all optional stand/
paper drawer units. These adjusters should be
lowered until they contact the floor.
5. Do not make any modifications to this machine.
Doing so may result in personal injury or damage to
the machine.
6. Since this machine is heavy, it is recommended that
it be moved by more than one person to prevent
injury.
7. When connecting this machine to a computer, be
sure to first turn both the computer and the machine
off.
8. Do not print anything which is prohibited from printing
by law. The following items are normally prohibited
from printing by national law. Other items may be
prohibited by local law.
●Money ●Stamps ● Bonds ● Stocks
●Bank drafts ●Checks ●Passports
●Driver's licenses
9. Do not throw toner or a toner cartridge into fire.Toner
may be spattered, causing a burn.
“BATTERY DISPOSAL”
THIS MACHINE CONTAINS A LITHIUM BATTERY WHICH MUST BE DISPOSED OF PROPERLY. CONTACT
YOUR IMAGISTICS DEALER OR SERVICER FOR INSTRUCTIONS.
This product utilizes tin-lead solder, and a fluorescent lamp containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance:
www.eia.org